Freezer Shelf (Number Varies By Model); Vacation And Moving Care - Whirlpool WRS555SIHZ06 Owner's Manual

Light Shield Reinstallation:
Place the left end of the light shield into the wall slots; then snap
the right end into its wall slots.
Freezer Shelf (number varies by
model)
To Remove and Replace the Bottom Shelf:
1. Lift up the front and back of the shelf, and remove from the
cabinet. Be sure not to remove the retaining rods.
2. Replace the shelf, aligning the rods with the cabinet ribs.
Apply a little pressure on the shelf to attach the rods to the ribs
of the cabinet.
To Remove and Replace the Mid and Top Shelf:
1. With your hand, push the shelf from bottom to top until it is
released from the holding rod. Pull the shelf until it is released
from the rear rod. Remove from the cabinet.
2. To replace the shelf:
� Replace rods into the support holes. Push the rods down
so they click into the holes.
� Identify the front and rear trim of the shelf.
� Place the rear trim on the rear rod and push the shelf so it
clicks the rod into the rear trim. (Keep the front raised while
pushing.)
� Lower the front of the shelf until the front trim is on the rod
and push the shelf down so it clicks the rod into the front
trim.
NOTE: Be sure that both sides of the shelf are positioned evenly
in the shelf support holes and the shelf is secure.

Vacation and Moving Care

Vacations
If You Choose to Leave Refrigerator On While You Are Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker and is
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Depending on your model, raise the wire shutoff arm
to Off (up) position or press the switch to Off.
4. Empty the ice bin.
If You Choose to Turn Refrigerator Off Before You Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
� Turn off the water supply to the ice maker at least one day
ahead of time.
� When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position or move the switch to the Off
setting.
3. Depending on the model, turn the refrigerator control to Off or
turn cooling off. See "Control Descriptions" in the Quick Start
Guide.
4. Unplug refrigerator or disconnect power.
5. Clean, wipe, and dry thoroughly.
6. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
� Turn off the water supply to the ice maker at least one day
ahead of time.
� Disconnect the water line from the back of the refrigerator.
� When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position or move the switch to the Off
setting.
2. Remove all food from the refrigerator and pack all frozen food
in dry ice.
3. Empty the ice bin.
4. Depending on the model, turn the refrigerator control to Off or
turn cooling off. See "Control Descriptions" in the Quick Start
Guide.
5. Unplug refrigerator or disconnect power.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
together so they don't shift and rattle during the move.
8. Depending on the model, raise the front of the refrigerator so it
rolls more easily, or screw in the leveling legs so they don't
scrape the floor. See "Adjust the Doors" or "Door Removal,
Leveling and Alignment" in the online Feature Guide.
9. Tape the doors closed and tape the power cord to the back of
the refrigerator.
When you get to your new home, put everything back and refer to
the Installation Instructions for preparation instructions. Also, if
your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
5