Related Manuals for Golden MAXICOMFORT PR512MLA
Summary of Contents for Golden MAXICOMFORT PR512MLA
- Page 1 Power Lift & Recline Chair OWNER’S MANUAL MAXICOMFORT MODELS ™ PR632 PR512MLA 401 Bridge Street Old Forge, PA 18518 www.goldentech.com...
- Page 2 We hope that your Golden chair provides years of comfort and enjoyment, while assisting you in both sitting down and standing up.
-
Page 3: Safety Guidelines
Safety Guidelines The symbols below are used in the owner’s manual and/or on the product to identify warnings and notify you of important safety information. Make sure you read and understand them completely. WARNING! Indicate(s) a hazardous situation which, if not avoided, could result in death or serious injury. - Page 4 continued from previous page Safety Guidelines Class II Device! Indoor use only! Do Not Smoke! Electrical hazard! Do not dispose in trash! Batteries required!
- Page 5 Your power lift and recline chair has been engineered from the leg levelers up to provide the ultimate in strength and reliability. Great care has been taken to provide you with total comfort and safety. Golden Technologies thoroughly inspects and tests each unit prior to shipment.
- Page 6 Do not smoke while operating, sitting or resting in the chair. To reduce risk of electrical shock, do not immerse any of the electrical components into a liquid, or spill any liquids onto electrical components. Do not open any of the electrical components. There are no serviceable parts.
- Page 7 Consult the owner’s manual of the chair and a physician to determine if you are capable of moving or lifting the chair, as this will cause serious injury if not done properly. Verify that all objects including hands and fingers are not between the arm of the chair and the open compartment before closing the compartment as this will result in property damage or serious injury.
- Page 8 INSTALLATION MAXICOMFORT MODELS There are three external power source scenarios depending on the model of your chair. 1. Transformer without battery back up. (Note: An uninterruptible power supply or UPS, may be purchased from an outside source as a battery backup). 2.
- Page 9 Installation - continued 4. Adjust the leg levelers on the bottom of the chair if necessary to level the chair. Some high pile carpets can obstruct the footrest operation by rubbing against it. Raise the levelers to a height above the pile. 5.
- Page 10 3. Lift the seat back up and off the seat of the chair. Battery Backup Systems Your Golden power lift chair may come with a battery back up system depending on the model, so the chair can return to the seated position in the event of a household power failure.
- Page 11 rive ontrol perAtion 1. Getting into your lift chair. While standing next to your chair, press button (S7) and raise the chair to a height you can sit against. This height will vary from person to person depending on the individual’s needs. Raise the chair high enough so you do not have to flop down into the chair.
-
Page 12: Factory Reset
1. Press and hold program button (SP). The back light goes off while pressed. 2. In about 3 seconds the backlight will start flashing (one flash) 3. Within 5 seconds, press one of the memory buttons (S5, S6, S8, S10) to save the position to the button pressed. - Page 13 Chair Operation Model PR535-M26 1. To recline the back of the chair, press button (S1) and hold until the back reaches the desired position. Then release the button. 2. To bring the back of the chair to an upright position, press button (S2) and hold until the back reaches the desired position.
- Page 14 and could cause personal injury. Press button (S3 or S5). As the chair continues downward, adjust yourself into a position that is comfortable to you. Continue holding button until chair is in the seated position (chair firmly on the floor), then release the button. Continue operating the chair with buttons S1 thru S6 until you reach your desired position.
- Page 15 rive ontrol perAtion Model PR512 1. Getting into your lift chair. While standing next to your chair, press button (S7) and raise the chair to a height you can sit against. This height will vary from person to person depending on the individual’s needs. Raise the chair high enough so you do not have to flop down into the chair.
- Page 16 Programming the Memory Buttons S8 and S10 Press one of the preprogrammed buttons (S8, S10) and hold until the chair stops. Press buttons (S1 thru S4) to micro adjust those positions to suit your needs. Use the following procedure to reprogram (S8, S10) buttons after you have the chair in your desired position.
- Page 17 & l rive umbAr ontrol perAtion 1. Getting into your lift chair. While standing next to your chair, press button (S7) and raise the chair to a height you can sit against. This height will vary from person to person depending on the individual’s needs. Raise the chair high enough so you do not have to flop down into the chair.
-
Page 18: Troubleshooting
Initial Hand Control Setup This setup is required to ensure proper operation of your lift chair’s control system. ZK3200-HC Setup/Reset Procedure: Press and hold both buttons (S1) Backrest down and (S3) Footrest up simultaneously (see photo) until the chair stops moving. - Page 19 Programming the Memory Buttons S5, S6, S8 and S10 Press one of the preprogrammed buttons (S5, S6, S8, S10) and hold until the chair stops. Press buttons (S1 thru S4) to micro adjust those positions to suit your needs. Use the following procedure to reprogram (S5, S6, S8, S10) buttons after you have the chair in your desired position.
- Page 20 Lights Out Feature: This feature will automatically shut off the backlight on the hand control after a specified period of inactivity (approximately 15 seconds). To activate the “Lights Out Feature”, follow the procedure below. 1. Press and hold the (SP) button “M”, until the backlight starts flashing. 2.
- Page 21 Shown below are some of the Maxi Comfort positions. There are many to choose from. You may stop your Golden power lift chair at one of the positions shown or anywhere in between just by releasing the buttons on the hand control when the chair reaches the position you desire.
-
Page 22: Care And Maintenance
CARE AND MAINTENANCE our lift chair will require routine maintenance checks. You can perform some of these checks, while others may require assistance from a provider. By following these maintenance checks, you can make sure your lift chair gives you years of trouble-free operation. If you have any questions or concerns regarding your lift chair’s care and maintenance, contact your provider. - Page 23 LIFETIME WARRANTY GOLDEN, warrants for the lifetime of the chair by the original consumer to repair or replace at their option the Lift Mechanism, Chair Frame and Recline Mechanism. Labor to replace these parts is subsidized on all models for three years.
- Page 24 ULTRAFABRICS GOLDEN WARRANTY Q&A Here are a few answers to Frequently Asked Questions: What is Delamination? Delamination is failure in a laminated material, often a composite, which leads to separation of the layers of reinforcement or plies. Delamination failure can...
- Page 27 Buzzaround XL! Featuring a 300 lb. weight capacity, the Buzzaround XL disassembles quickly and easily. othing beats the luxury of the Golden Companion scooter line! The Companions feature our patented adjustable tiller, bright head and tail lights and a plush seat. Weight capacities of 350 and 400 lbs.
-
Page 28: For Your Records
For Your reCorDs Please fill in your Power Lift & Recline Chair information below. This information will be useful in the event that you should ever need to contact Golden Technologies, Inc. concerning your lift chair. Date of Purchase _____________________________________________ Model ______________________________________________________ Serial Number _______________________________________________ Your Golden Technologies, Inc.