Table of Contents
Related Manuals for Soneco SCS3
Summary of Contents for Soneco SCS3
- Page 1 ™ 1(20) Soneco CC3 / SCS3 USER MANUAL SONECO Oy Tuotekuja 5 FIN-90410 Oulu Finland Tel. +358 41 431 9221 e-mail: info@soneco.fi www.soneco.fi © Soneco Oy March, 2022 © Soneco Oy. V 28.3.2022 Staus: Contents checked Author: JR...
-
Page 2: Warranty
In consumer trade Soneco is liable for the warranty defined by EU regulations. The authorized seller of Soneco products will either repair or replace the defective device that falls under warranty. The warranty does not apply to wear due to use or accessories. The warranty does not apply if the device has been in wrong or inappropriate use, opened, altered, connected to other equipment, used with other charger than Soneco P4300 or P3500. -
Page 3: Table Of Contents
12. Shutting the device off..................14 13. Request for battery charge status ..............14 14. Voice call features in alarm state of CC3 and SCS3........14 15. Emergency call 112..................14 16. Remote controlled voice call "CALL" and termination of a call "END CALL" and queuing of a call ....................15... -
Page 4: Purpose Of Cc3
4(20) Purpose of CC3 Soneco CC3 is a small radio device for voice calls and text messages (SMS). With a single press of its only button, CC3 makes a voice call to one of telephone numbers and can send a SMS to one or several numbers simultaneously. -
Page 5: Quick Procedure For Using The Device For The First Time
Chapter 12. 8. Please remember to charge the battery as instructed. Programming commands can be created according to this manual or generated with using Soneco's site www.soneco.fi/settingsaid. © Soneco Oy. V 28.3.2022 Staus: Contents checked... -
Page 6: Charging Of The Battery
6(20) 1. Charging of the battery Insert the DC cable's plug (3,5 mm) of either SONECO P4300 or P3500 charger to the connector on the side of the device. The progress of charging is displayed by the brightness of the YELLOW light. If the battery is depleted, pre-charging takes place. -
Page 7: The Programming Mode
4C DEVICE WITH INHIBITED MANUAL ENTRY TO PROGRAMMING MODE Programming mode is possible only if the device receives a <<<PRG>>> command as SMS from a number that is stored in the device or from Soneco Oy. EXECUTION OF A PROGRAMMING COMMAND... -
Page 8: Setting The Alarm Message
The message is set in programming mode with a message to the device. The message has to contain between command brackets “<<<” and “>>>” a command "sms:" and the message with a maximum length of 150 characters as below <<<sms:Own_message>>> E.g.<<<sms:Contact reception>>> © Soneco Oy. V 28.3.2022 Staus: Contents checked Author: JR... -
Page 9: Basic Settings
The basic settings define how the device makes the calls and sends the messages when the button is pushed. The basic settings have been set according to customers’ wishes by Soneco during the manufacturing. These basic settings can be altered with the programming command <<<CCxabc>>>... -
Page 10: Options For Voice Calls
This tone is generated by SONECO device itself and comes from the earpiece. x3 is the stepping tone of calling machine. It is buzzer beep which is heard each time the calling machine starts to call the next number. -
Page 11: Security And General Settings
M3 the messages will be sent before starting the calling procedure (recommended). SPIN:Ab1& Security code for management commands in standby mode. If the code is set, access from the SONECO's service number requires a correct SPIN. SPIN is four (4) upper or lower case characters, numbers or other characters of basic ASCII. -
Page 12: Standby Mode
™ 12(20) Soneco's own nonpublic telephone number. The management commands and the use require additionally, the telephone number of the device to be known. The options can be programmed one by one (e.g. <<<P1>>>) or combined in to a single command e.g., to the following example command <<<S1F1P1W01100>>>... -
Page 13: Receiving And Terminating Of The Calls
During this mode the call can be directed to the stored number that sends a message to the device. This mode can be terminated with a press of the button after which the device returns to the standby mode. © Soneco Oy. V 28.3.2022 Staus: Contents checked... -
Page 14: Shutting The Device Off
14. Voice call features in alarm state of CC3 and SCS3 CC3, SCS3 or MC3 can be programmed to other device type If CC3 is reprogrammed to MC3, please refer to User's Guide for MC3. -
Page 15: Remote Controlled Voice Call "Call" And Termination Of A Call "End Call" And Queuing Of A Call
(e.g. by the hand) or with rising to a higher elevation within the building or in the landscape. Charging the battery is possible only at temperatures between 0 and 45 °C. © Soneco Oy. V 28.3.2022 Staus: Contents checked... -
Page 16: Data Security, Privacy, Reliability And Prevention Of Abuse
If an entry to the programming mode by the user has been prevented and the users have lost the information for sending and acceptable PRG-command, the GSM phone number of Soneco's service can command the device in to programming mode and read the technical information. This number can not control the calls or the messages nor can it be used as a calling number. -
Page 17: Annex A: Tone And Light Indications Of Cc3
GREEN, YELLOW and RED blink alternating with a melodic ringing tone. Incoming call. Note that the call may be set as silent. Tones and YELLOW blinks in ca. one minute interval: Battery charge low. © Soneco Oy. V 28.3.2022 Staus: Contents checked... - Page 18 The RED blinks continuously in 0,5 second interval. The device in LIMITED mode for following reasons: No SIM, SIM error, PIN-error, no network coverage. The only possible actions are the shut-off and an emergency call. © Soneco Oy. V 28.3.2022 Staus: Contents checked...
- Page 19 The vibrations and tones are slightly longer than when using tones only. The sound frequency is ca. 600 Hz in order to be in the human ear's stereo hearing range which helps in locating the device according to the sound. See D-settings. © Soneco Oy. V 28.3.2022 Staus: Contents checked...
-
Page 20: Important To Observe
Operating temperature: -10 ... + 55 C (when charging, 0 ... + 45 C) SIM card: 3,0 V SAR: < 0,5 W/Kg Operating voltage: 3.7 V 0523 Declaration of conformity: The product complies with the requirements of the European Council directive 1999/5/EY. © Soneco Oy. V 28.3.2022 Staus: Contents checked Author: JR...
Need help?
Do you have a question about the SCS3 and is the answer not in the manual?
Questions and answers