Subscribe to Our Youtube Channel
Related Manuals for Foxtech EH30-TIR
Summary of Contents for Foxtech EH30-TIR
- Page 1 EH30-TIR Dual Sensor 30X Optical Zoom Camera with 3-axis Gimbal User Manual 2021.08 V1.0...
-
Page 2: Note
Please read the instruction manual carefully and strictly follow the requirements of this manual to install and use this product. Foxtech will not bear any legal responsibility for any results or losses caused by improper use, installation, final assembly and modification by users. -
Page 3: Table Of Contents
Video Transmission System Ground Station Software Extension Module Installation (with notes) Hardware Installation Software Installation and Configuration Installation and setup methods of third-party videolink GCS Software Usage Instructions Connection Operating Pods Operating Pods Frequently Asked Questions 2020 FOXTECH All Rights Reserved ©... -
Page 4: System Composition
System Composition Product System Atlas Product Wiring Diagram Connection method, interface type of professional load and the lightweight load are consistent, only interface position is different. The following is illustrated with a professional load. 2020 FOXTECH All Rights Reserved ©... -
Page 5: Pod
Foxtech EH30-TIR Dual Sensor 30X Optical Zoom Camera User Manual SBUS, professional pod wiring diagram The receiver needs separate power supply, and adapt module need to be powered through the receiver. please connect the serial port in the process of parameter adjustment, needn’t connect series port during normal operation. -
Page 6: Idu/Idus
100ms. You can use the traditional microwave point-to-point video transmission while using the IRIS 4G video transmission function, double guarantee to ensure the link security. 2020 FOXTECH All Rights Reserved ©... -
Page 7: Installation (With Notes)
After setting up, open the GCS software to click on the connection select the corresponding pod. When the image appears, the full display control settings of the pod can be realized B. PC software installation and setup Refer to corresponding GCS usage instructions 2020 FOXTECH All Rights Reserved ©... -
Page 8: Installation And Setup Methods Of Third-Party Videolink
192 168 42 255 255 255 0 192 108 42 3. Use GCS ground station for gateway setting Click to search device, then double-click the pop-up IP bar, save it after modification, and restart the gimbal. 2020 FOXTECH All Rights Reserved ©... - Page 9 4. Camera IP modification Open any browser, enter 192.168.42.108 After entering the following interface, username, password are admin Confirmation 2020 FOXTECH All Rights Reserved ©...
- Page 10 Do not modify the password, otherwise the software will not working properly. After entering the setup interface, click Settings Network Settings General Settings Change the IP address and default gateway “42” to “1”, then click Save. 2020 FOXTECH All Rights Reserved ©...
- Page 11 Secondary stream 1 rtsp ://admin: admin @< ip >:554/cam/realmonito? Channel =1& subtype =1 Secondary stream 2 rtsp ://admin: admin @< ip >:554/cam/realmonito? Channel=1& subtype=2 usually uses secondary stream 2 for preview RTSP ://admin: admin @192.168.1.108:554/cam/realmonito? Channel=1& subtype=2 rtsp://101.132.41.33:554/0xea9d0567110909d4/subtype= 2020 FOXTECH All Rights Reserved ©...
-
Page 12: Gcs Software Usage Instructions
When the image appears, the full display control settings of the pod can be realized. Operating Pods GCS pod software through the mouse, virtual keys, USB joystick to achieve the full operation of the pod. 2020 FOXTECH All Rights Reserved ©... - Page 13 5.View size shifting Manual focus- 6.Dual sensor mode shifting 7.Dual sensor window shifting 8.Window shifting Camera zooming pod up, down, left and right control Down press return to 1X Down press then Yaw following 2020 FOXTECH All Rights Reserved ©...
-
Page 14: Operating Pods
1. Operational steps view → download interface (as shown below) can download video (MP4 style), photo (jpg) offline. And the photos support real-time preview. Download type switch Photo preview window 2020 FOXTECH All Rights Reserved ©... -
Page 15: Frequently Asked Questions
IP) Open GCS software → network settings Modify the IP address. This content is subject to change. Download the latest version from https://www.foxtechfpv.com/eh30-tir-30x-optical-zoom-camera-3-axis-gimbal.html For everyday updates, please follow Foxtech facebook page"Foxtechhobby". YouTube Channel: Foxtech 2020 FOXTECH All Rights Reserved ©...
Need help?
Do you have a question about the EH30-TIR and is the answer not in the manual?
Questions and answers