Table of Contents
Advertisement
Quick Links
PS130
SANITARY PRESSURE
SUSTAINING VALVE
INSTALLATION AND MAINTENANCE INSTRUCTIONS
VALSTEAM ADCA
We reserve the right to change the design and material of this product without notice.
IMI PS130.08 E 00.22
Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive.
Advertisement
Table of Contents
Related Manuals for VALSTEAM ADCA PS130
Summary of Contents for VALSTEAM ADCA PS130
- Page 1 INSTALLATION AND MAINTENANCE INSTRUCTIONS VALSTEAM ADCA We reserve the right to change the design and material of this product without notice. IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive.
- Page 2 GENERAL INFORMATION • These instructions must be carefully read before performing any work involving VALSTEAM ADCA products. Failure to observe these instructions may result in hazardous situations. • These instructions describe the entire life cycle of the product. Keep them in a location that is accessible to every user and make these instructions available to every new owner of the product.
-
Page 3: Table Of Contents
9.1. Maintenance procedure 9.2. Replacing the diaphragms and plug assembly 9.3. Tightening torques 10. TROUBLESHOOTING 11. DISPOSAL 12. RETURNING PRODUCTS VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 4: Safety Information
This includes checking application, material suitability, process medium, pressure and temperature as well as their respective limiting values. VALSTEAM ADCA does not assume any responsibility for damage resulting from inappropriate use of the product, damage caused by external stresses or any other external factors. -
Page 5: Qualification Of Personnel
Unauthorized modifications to the product. If the product is to be used for an application or with a fluid other than the one it was designed for, contact VALSTEAM ADCA. 1.3. Qualification of personnel Handling, installation, operation and maintenance work must be carried out by fully trained and qualified personnel, capable of judging the work which they are assigned to perform and recognizing potentially hazardous situations. -
Page 6: Atex
Do not use the product with mediums other than the ones it was designed for. Check section 1.2 - Intended Use. • Prevent medium contamination. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. - Page 7 Drain the process medium from the product and all the relevant plant sections. • Wear protective clothing, safety gloves, mask, and eye protection. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive.
-
Page 8: Product Information
ADCA. 2. PRODUCT INFORMATION The ADCAPure PS130 is a direct acting, diaphragm sensing pressure sustaining valve. This spring-loaded regulator is designed for use with clean air, nitrogen, carbon dioxide, oxygen, argon and other gases or liquids compatible with the construction materials and valve design. -
Page 9: Certification
This product has been specifically designed for use with liquids and gases which are in Group 2 of the European PED – 2014/68/EU Pressure Equipment Directive and it complies with its requirements. PS130 – CE MARKING – GROUP 2 (PED – European Directive) PN 16 Category... -
Page 10: Product Identification
The following items are indicated on the product nameplate or directly on its body: • Manufacturer • Product model (e.g. PS130) • Pressure rating (e.g. PN 16) or maximum allowable pressure (e.g. Pmax = 16 bar) • Nominal size (e.g. TC 1/2" BPE) •... -
Page 11: Transport, Storage And Packaging
The product is stored in a cardboard box as it leaves VALSTEAM ADCA. Avoid removing packaging, covers and sealings until immediately before installing the product at the site. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 12: Installation
Make sure that the connected pipe does not subject the body to any stress (forces or torques) during installation and operation. • Do not use the product as an elevation point. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 13: Preparation For Installation
A pressure gauge is installed both upstream and downstream of the regulator for monitorization, set point adjustment and troubleshooting. • In steam applications (not recommended for the PS130), it should be dry and free of impurities. A humidity separator with an appropriate trapping set trap is strongly recommended. -
Page 14: Installation Procedure
• The adjustment spring is completely relaxed. If not, release tension by turning the adjustment knob (26) counterclockwise. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 15: Start-Up Procedure
24 hours after system start-up, it is recommended to check pipe connection for leaks and retighten when necessary. Clean strainers/filters to avoid blocking. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 16: Operation
7. If the pressure regulator is to be removed from the pipeline – see section 3 - Transport, storage and packaging. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 17: Parts List
8. PARTS LIST Fig. 2 VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. - Page 18 Serrated washer * O-ring Adjustment spring * Compression fitting Spring guide * Only for versions with leakage line option. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive.
-
Page 19: Maintenance
9. Apply a suitable lubricant on the cover (2) thread and screw it into the valve body (1) tightening with the recommended torque – see section 9.3 – Tightening torques. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 20: Tightening Torques
(no a larger regulator or a second regulator in consumption). parallel. • Contact VALSTEAM ADCA. VALSTEAM ADCA IMI PS130.08 E 00.22 Produced in accordance with Sound Engineering Practices of the European PED - Pressure Equipment Directive. -
Page 21: Disposal
VALSTEAM ADCA personnel. • Information regarding any hazards or precautionary measures to be considered must be provided in writing when returning products to VALSTEAM ADCA. • Health and Safety information sheets relating to any substances identified as hazardous or potentially hazardous must be provided outside the packaging.
Need help?
Do you have a question about the PS130 and is the answer not in the manual?
Questions and answers