Identification Of Parts; Assembly; Operation - Texas A/S WR1800 User Manual

Identification of parts

Figure 1
1. Safety lock-off
2. On/Off switch
3. Adjustment lock for turning the handle
4. Additional handle
5. Height adjustment
6. Guard hood
7. Guide wheel
Figure 2
8. Nylon brush
9. Wire brush
10. Pin
11. Open-ended wrench
12. Nut
13. Battery pack
14. Charger
15. Screws for the guard hood

Assembly

Figure 3
Connect the upper part of the housing and the bottom
part of the housing together
Figure 4
Mounting the wheel.
Insert the axle of the wheel into the mounting hole
Push the wheel to the suitable location.
Figure 5
Mounting the guard.
Fit the guard hood as shown and secure with 2 screws
Figure 6
Fit the brush (Fig. 6a/Item A) onto the drive axle (Fig.
6a/Item B). Make sure that the brush fits accurately into
the mount (Fig. 6a/Item C). The shaft must be fixed in
order to fasten the brush. To do so, insert the pin (Fig.
2/Item 10) into the recess on the shaft (Fig. 6b) and
hold with one hand. Using the open-ended wrench (Fig.
2/Item 11), tighten the nut (Fig. 6b/Item 12).
Warning!
Always take away the battery before inserting or
removing a brush
Figure 7
Height adjustment.
Undo the union nut (Fig. 7/Item 5) until the paving
scraper's handle can be moved in and out freely. Now
set the required working height and secure the handle
in this position by tightening the union nut again.
Figure 8
Adjusting the additional handle.
Undo the adjustment lock (Fig. 8/Item 3) for the
additional handle until it can be moved forwards and
backwards without any great resistance. Set the
required position and tighten the securing screw again.
Figure 9
Installing the battery.
Press the side push lock buttons of the battery pack as
shown in Fig. 9 and push the battery pack into the
mount provided. Make sure that the push lock buttons
latch in place! To remove the battery pack, proceed in
reverse order.
Figure 10a
Charging the battery.
1. Take the battery pack out of the equipment. Do this
by pressing the side push lock buttons.
2. Check that your mains voltage is the same as that
marked on the rating plate of the battery charger. Insert
the power plug of the charger (14) into the socket outlet.
The green LED will then begin to flash.
3. Insert the battery pack (13) into the battery charger
(14).
Figure 10b
Battery capacity indicator.
Press the switch for the battery capacity indicator (Fig.
10b/Item A). The battery capacity indicator (Fig.
10b/Item B) shows the charge status of the battery
using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED flashes:
The battery is empty, recharge the battery.
All LEDs flash:
The battery pack has undergone exhaustive discharge
and is defective. Do not use or charge a
defective battery pack!
Warning!
When the appliance is stopped, don't start the
appliance again.
The battery is not full charged when delivered, please
ensure it is fully charged before you use it the first time.
Charge it 5 hours the very first time.
If the machine cannot work when turn on the switch, it
means the battery is out of power, Recharge it.
Always disconnect power before changing brush!
Remember!
You can buy additional brushes:
Nylon brush:
Steel brush

Operation

Use the electric weed cleaner to remove weeds
between flagstones and pavers.
Adjust the support handle, so you have the best
possible control of the machine
Activate brush by activating handle with fingers, while
locking mechanism on the side of the handle is
activated. Release both to stop.
Do not press the brush down onto the surface. This will
increase the pressure on the brush and decrease its
Art. no. 90063100
Art. no. 90063090
10