Related Manuals for BBT PHD-71CC
Summary of Contents for BBT PHD-71CC
- Page 1 All manuals and user guides at all-guides.com OWNER’S MANUAL Assembly & Operating Instructions BBT 71CC Post Hole Digger MODEL NO. BBT-PHD-71CC...
-
Page 2: To The Owner
Please do NOT return the Post Hole Digger without first contacting the Customer Support Department at bbt@bbta.com.au. If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this Post Hole Digger, please contact our Customer Support Department. SAVE THESE INSTRUCTIONS WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 3: Table Of Contents
Auger Maintenance ......................12 Transporting Your Earth Auger ..................12 Long Term Storage ......................13 SERVICE, TROUBLESHOOTING AND REPAIR ............14 Service ..........................14 Troubleshooting .........................14 WARRANTY & SERVICE ..................15 EXPLODED DIAGRAM & PARTS LIST................16-17 YOU MAY ALSO LIKE .................... 18 BBT-PHD-71CC WWW.BBTA.COM.AU... -
Page 4: Important Safety Information
We reserve the right to discontinue, change, and improve our products at any time without notice or obligation to the purchaser. The descriptions and sections contained in this manual were in effect at the time of printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your machine. WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 5: Key To Symbols
Protect the equipment from rain and damp. Take care of mechanical hazards. WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. SAVE THESE INSTRUCTIONS! BBT-PHD-71CC WWW.BBTA.COM.AU... - Page 6 If the auger will not turn in the hole, turn engine off and allow to cool before attempting to remove it manually. • Do not let persons who do not fully understand the manual thoroughly to operate the auger. • When operating the auger make sure to keep bystanders a minimum of 15 metres away. WWW.BBTA.COM.AU BBT-PHD-71CC...
-
Page 7: Engine Safety Precautions
Clean up spilled fuel immediately. • Allow spilled fuel to dry, after wiping and before starting. • Allow fuel fumes/vapours to escape from the area before starting engine. • Test the fuel cap for proper installation before starting and using engine. BBT-PHD-71CC WWW.BBTA.COM.AU... -
Page 8: Parts Location
Choke lever Handle Air filter Transmission complete Pin shaft Auger 10. Fuel tank cap 11. Assembly Trigger 12. Cotter pin ASSEMBLING Set the auger on the output shaft, then insert the pin shaft, then lock it with cotter pin. WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 9: Operation
Immediately replace fuel cap and tighten. Wipe off Clean debris from area around the fuel cap. spilled fuel and allow to dry before starting engine. Loosen fuel cap slowly. Place the cap on a clean, dry surface. BBT-PHD-71CC WWW.BBTA.COM.AU... -
Page 10: Normal Operation
Remove engine from throttle to desired speed. area to avoid sparks. NOTE: Run at full throttle when possible. Do not let unit idle for extended periods of time. To stop engine, push rocker switch to OFF position. WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 11: Specifications
C.D.I. Starting System Recoil Gear Ratio 30:1 Max. Engine Speed 8500 r/min Clutch Engine Speed 3700 r/min Idle Engine Speed 2900 r/min Auger Speed 0-280 r/min Spark plug type /model L7RTC/TORCH Specifications subject to change without prior notice. BBT-PHD-71CC WWW.BBTA.COM.AU... -
Page 12: Maintenance
Run engine to use up the fuel in the carburettor and operation. Clean filter daily in extremely dusty conditions. fuel tank. Always run engine in a well ventilated area. Wipe away any spilled fuel from engine and auger. Allow to dry. WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 13: Long Term Storage
Avoid injury! Engine must be turned off and cooled, spark plug wire must be removed from spark plug before checking and adjusting engine or before any repair or maintenance can be done. Avoid injury! An adult must always do maintenance and repair on engine and auger. BBT-PHD-71CC WWW.BBTA.COM.AU... -
Page 14: Service, Troubleshooting And Repair
Replace clutch shoes and spring Worn engine lower seat Call factory Auger jumps Blade damaged Replace with new blade Auger cuts slowly Dull blade Buy new blade, or have blade sharpened at factory Damaged fishtail point Replace fishtail point WWW.BBTA.COM.AU BBT-PHD-71CC... -
Page 15: Warranty & Service
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Spare Parts Spare parts are available. Please see our website (www.bbta.com.au) or contact us at bbt@bbta.com.au for more details. BBT-PHD-71CC... -
Page 16: Exploded Diagram & Parts List
All manuals and user guides at all-guides.com EXPLODED DIAGRAM & PARTS LIST WWW.BBTA.COM.AU BBT-PHD-71CC... - Page 17 All manuals and user guides at all-guides.com EXPLODED DIAGRAM & PARTS LIST DESCRIPTION DESCRIPTION SP-PHD-71CC-001 GAS ENGINE, 71CC SP-PHD-71CC-016 BALL BEARING R10 SP-PHD-71CC-002 HANDLEBAR ASSEMBLY SP-PHD-71CC-017.2 GEAR 48T SP-PHD-71CC-003 TRANSMISSION COMPLETE SP-PHD-71CC-017.3 GEAR 10T SP-PHD-71CC-004 TRIGGER ASSEMBLY SP-PHD-71CC-018 GEAR CASE BOTTOM SP-PHD-71CC-005 BOLT PPH 10-24×16...
-
Page 18: You May Also Like
All manuals and user guides at all-guides.com YOU MAY ALSO LIKE Chainsaws Blowers Lawn Mowers Chainsaw Sharpeners COPYRIGHT © BIGGER BOYZ TOYZ AUSTRALIA PTY Unit 2/3 Delta Place Albion Park Rail NSW 2527 BBT-PHD-71CC-MNL1802...