Contents Foreword Caution ............................3 Important Safety Information ....................5 Overviewing your the Monitor Viewing the Control Panel ...................... 9 Viewing the Connecting Panel ......................10 Viewing the Remote Control - Key Description ..........................12 - PIP(Picture In Picture) Keys ......................13 - Loading the Batteries ........................
Important Safety Information Use only the accessory cord designed for this product Provide ventilation for the Monitor. The unit is designed to prevent shock. The power supply voltage rating of with slots in the cabinet for ventilation to protect it from this product is AC100-240V, the power cord attached overheating.
Viewing the Remote Control Choose the MTS (Stereo) mode. Each time it is pressed, different mode is selected. Mono ➔ Stereo ➔ SAP • You can select only available modes depending on the source. CH INFO Display the current information about time, screen form, source and MTS mode.
Page 5
Viewing the Remote Control Move key : Move the position of PIP window. Right Up (Start) Left Up Right Down Left Down Swap key : Swap the sources of the main screen and PIP window. MODE KEY : Change the PIP window mode. OFF ➔...
Viewing the Remote Control Loading the Batteries Load two AAA batteries, taking Close the cover until it clicks. Press on the cover and slide care that the + and - ends face in the direction of the arrow. the correct direction. Reception Range of Remote Control OWNER'S MANUAL...
Installation Table Stand Installation (Optional) < The Monitor can be installed on the desk as shown above. > • Table Stand mount minimum allowable clearances for adequate ventilation. 1.18 inch (3Cm) 4 inch(10.16Cm) 4 inch 4 inch (10.16Cm) (10.16Cm) 2.36 inch (5.99Cm) Installation OWNER'S MANUAL...
Installation Speaker Installation (Optional) • Be sure monitor power is turned off before making any connections. Place the speakers in the position you want. Install the speaker wires on the monitor and speaker. Be sure to connect the positive "+" wire to the "+" input and the negative "-" wire to the "-" input. Connect left monitor input to left speaker and right monitor input to right speaker.
Connecting the TV Cable Connecting the TV Cable Connect the TV antenna cable to the TV input jack. Press INPUT button on the remote control and select TV on OSD. Use CH+, CH- button or numeric button to change TV channel for your channel selection. Press Pre.CH button on the remote control to tune the previous channel.
Connecting the VCR Connecting the VCR With S-Video Connect a S-Video cable to the S-Video jacks of the VCR and the Monitor. Connect L (White), R (Red) sound cable (composite) to the sound jacks of the VCR and the Monitor. With AV input Connect a composite cable to the AV video jacks of the VCR and the Monitor.
Connecting the DVD Connecting the DVD • Connect the three separate component video cables to the DVD player's Y, Pb and Pr jacks and to the Component jacks on the Monitor. • Connect the audio cable to the DVD player's audio L (White) and R (Red) jacks and to the L and R audio jacks beside the Component jacks on the Monitor.
Connecting the Set Top Box How to connect Connect Set Top Box video inputs to AV, COMPONENT, PC or DVI jacks on the Monitor. Audio inputs to Audio sockets beside the L (White) and R (Red) audio jacks which you connect video inputs. How to use Supported Signals Component1...
Connecting the PC (D-Sub & DVI) Connecting a PC to the Monitor • There are two connectors to connect the Monitor and PC: D-Sub and DVI. • D-Sub Connect a PC (15pin) video cable between the Video Output port on the PC and the PC port on the Monitor. •...
Basic Operation Turning the Monitor On / Off Press the Power button on the remote control. The Monitor will turn on and you will be ready to use its features. You can also use the Power button on the front panel. Select Source Press INPUT button on the remote control.
OSD Menu Structure • OSD (On Screen Display) allows users to control or adjust various features and settings in accordance with his/her preferences. • Press the Menu/Set button on the remote control to see the main OSD menu. EXAMPLE of OSD Menu Picture Mode Standard...
Setting the Channel Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna, a standard cable system, an HRC, or an IRC). Press Menu/set button to display the main Channel Type CATV...
Setting the Channel Fine Tune The Fine Tuning function lets you manually adjust the Monitor's tuner if you have difficulty tuning analog Channels. Press Menu/set button to display the main OSD menu. Press Menu/set button to display the main OSD menu. Channel Type CATV Select the TV main menu item.
Important Safety Information Do not overload the wall outlet or Do not insert anything through the Bend antenna cable between inside extension cords. Overloading can openings in the unit, where they and outside building to prevent rain result in fire or electric shock. can touch dangerous voltage points from flowing in.
Page 20
Important Safety Information When replacement parts are Upon completion of any service or If you make adjustments yourself, required, be sure the service repairs to this the Monitor, ask the adjust only those controls that are technician uses replacement parts service technician to perform safety covered by the operating instructions.
Page 21
Viewing the Control Panel OSD Key Position Front Panel OSD key & Function Input Source Select DOWN (See the box below.) Power (Stand By) Remote Sensor Status / Power Indicator LED OSD Key Function INPUT SELECT Select the signal source from multiple input sources such as TV, AV 1, AV 2, S-Video / AV, Component1, Component2, PC and DVI.
Page 22
Viewing the Connecting Panel Back Panel and Jacks < Back panel of the monitor > RS-232C To control from PC. For PC, Set top box. PC Sound PC/DVI Audio Input. D-Sub (PC) For PC, Set top box. Component 1, 2 For DVD, Set top box.
Page 23
Viewing the Connecting Panel RS-232C Jack Connects a control signal from a PC. DVI Input Jack Connects a digital video signal from a DVI output jack of PC or Set Top box. PC Sound Connects a sound signal from PC or DVI. RGB PC Input Jack ( D-Sub ) Connects a video signal from a video output jack of PC.
Page 24
Viewing the Remote Control Key Description Power Turn the Monitor on and off. Mute Temporarily cut the sound and restore it. Pre.CH Turn to the previous channel or exit OSD. V.Size Choose the Screen Form. Wide ➔ Panorama ➔ Zoom1 ➔ Zoom2 ➔ 4:3 FAVORITE (FAVOURITE) Tune to your next favorite channel.
Page 25
Contents Setting the Picture Changing the Picture Mode ....................29 Adjusting the User Mode......................30 Changing the Color Temperature .................... 32 Video NR (Noise Reduction) ....................33 Changing the Screen Format ....................33 Adjusting the PC Screen (Geometry) ..................35 Setting the Sound Adjusting the Sound Balance ....................
Page 26
Caution CAUTION CAUTION RISK OF ELECTRIC SHOCK - TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD. DO NOT OPEN - DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. - SHOCK HAZARD DO NOT OPEN. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), CAUTION...
Page 27
Caution Always be careful when using your the Monitor. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine. 1. Read these instructions. 2. Keep these instructions. 3.
Page 28
Important Safety Information Follow all operating and use Unplug the Monitor from the Never add any attachments and/or instructions. wall outlet before cleaning. Use equipment without approval of the a damp cloth; do not use liquid manufacturer. Such additions can or aerosol cleaners.