Item Power Consumption Canister Capacity Battery Capacity Battery Type Battery Charger Delivery Viscosity Stainless Steel Nozzles Spray Functions Dimensions Weight Accessories You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual.
Page 3
Use eye, nose and mouth protection. Always wear ANSI approved impact safety goggles. Wear an ANSI approved dust mask or respirator when working chemical and paint dusts and mists. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines.
Read all instructions and warnings on the battery before charging the battery. To avoid accidents, charge the supplied battery only. Do not use a different charger with this battery. Do not expose the battery to rain or wet conditions. To avoid damage of cable and plug, never pull the cable to disconnect the charger. Do not use the charger if the cable or plug are damaged.
Page 5
Do not operate the Spray Gun without the nozzle Locknut (3) in place. Never use gasoline or other flammable liquids to clean the Spray Gun. Fire or explosion could occur. Damage to Spray Gun components could occur. 10. Always read the paint manufacturer’s thinning recommendations or instructions before using paint or other materials.
CHARGING BATTERY The Battery (26) does not come charged from the factory. Charge the Battery before using. AC Adapter (32) Insert the Battery (26) into the Charger Base (31). The Battery can only insert one way. Insert the AC Adapter (32) cord plug into the Charger Base as shown above. Plug the AC Adapter module into an electrical outlet.
The surface to be sprayed should be free of dust, dirt, and grease. In some instances, a primer coat should be applied before spraying the final coat. PREPARATION OF PAINT TO BE SPRAYED Most paints and stains are supplied ready for brush applications. They may need to be thinned before using in the Spray Gun.
Page 8
Lock Nut (3) Nozzle (1) Canister Lid (11) Suction Tube (23) Push the Suction Tube (23) back into the Canister Lid. Fill the Canister (25) with paint of the correct viscosity, then carefully screw the Canister back into the Canister Lid. Securely tighten. The easiest way to do this without spilling paint is to leave the full Canister on a flat surface.
MOUNTING THE SIDE HANDLE For ease of use and more spraying control, it may be desirable to mount the Side Handle (28) to the Housing (27). It can be mounted to either the left or right side of the Housing (27).
CHANGING THE NOZZLE Push the Switch Lock (21) to the Off position, and remove the battery. Unscrew the Nozzle (1) by turning it counterclockwise. Make sure that the Valve (2) remains in the Cylinder (4). Insert the new Nozzle (1) into the Cylinder (4) and securely tighten it clockwise.
Caution: Before performing any repair or maintenance procedure, remove the Battery from the Spray Gun Handle. Never immerse the Spray Gun in water to clean. Clean the Spray Gun components immediately after each use as described below. Unscrew the Canister (25) and pour the remaining paint back into the paint can. Thoroughly clean the Canister with the appropriate thinner/cleaner (water or paint thinner).
Symptom Motor hums but no spraying occurs; Or, irregular spraying Spray atomization is not good Over painting and dripping Motor is louder than normal Operating sound not normal Orange peel effect when spraying; Excessive fogging Spray Gun operates only for a short time SKU 90880 Troubleshooting Probable Cause...
Item NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU- TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.