Do you have a question about the 44677 and is the answer not in the manual?
Questions and answers
Lisa Mitchell
March 25, 2025
What would cause paint not to come out of the sprayer
1 comments:
Mr. Anderson
March 25, 2025
Paint may not come out of the Chicago Electric 44677 sprayer due to several reasons: 1. Clogged Spray Gun – If the spray gun is not cleaned immediately after use, dried paint can clog it. 2. Thick Paint Mixture – If the paint is too thick, the gun may not be able to atomize it properly. 3. Improper Gun Setup – Incorrect setup, including tip size, air pressure, or distance from the surface, can affect paint flow. 4. Inadequate Solvent – If the paint is not properly mixed with the correct solvent, it may not flow through the sprayer. 5. Drying Too Quickly – If the paint dries too fast before exiting the sprayer, it may block the nozzle.
Proper cleaning, correct paint viscosity, and proper setup can help resolve these issues.
This answer is automatically generated
JOHN F VAN HAL
May 30, 2025
missing the spray gun for a 44677 unit is it worth to buy if available or scrap the whole unit
Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock. SKU 44677 For technical questions, please call 1-800-444-3353. Specifications "...
23. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SKU 44677 For technical questions, please call 1-800-444-3353. Personal Safety...
12. WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. SKU 44677 For technical questions, please call 1-800-444-3353. Service...
Page 5
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 44677 For technical questions, please call 1-800-444-3353. Page 5...
(See Figure A.) DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS Figure B SKU 44677 For technical questions, please call 1-800-444-3353. GROUNDING Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc.,...
Thin your paint slightly and test on a piece of scrap material. If the paint goes on very thin and threatens to run, stop spraying immediately. Add more paint to your mixture to thicken the paint. Test on a piece of scrap material before resuming work. SKU 44677 For technical questions, please call 1-800-444-3353. Preparing to Paint...
Loosen and remove the Lock Ring (9), Air Cap (8), and Fluid Tip (7). Be careful not to allow any parts to fall out of the gun. SKU 44677 For technical questions, please call 1-800-444-3353. Unpacking Electric Compressor with Spray Gun.
Using a clean rag wetted with solvent, wipe off the Spray Gun to remove paint from the exterior. Store your paint sprayer in a clean dry place out of the reach of children. All servicing of the Electric Spray Gun Kit must be performed by a qualified service technician.
Page 11
Diagram and Parts List of Spray Gun l i r & & & SKU 44677 For technical questions, please call 1-800-444-3353. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replace- ment parts.
Page 12
Note: When ordering parts for the Compressor, be sure to include the suffix “a” after the part number. c t i SKU 44677 For technical questions, please call 1-800-444-3353. t l i t l i c i t y t i...
Need help?
Do you have a question about the 44677 and is the answer not in the manual?
Questions and answers
What would cause paint not to come out of the sprayer
Paint may not come out of the Chicago Electric 44677 sprayer due to several reasons:
1. Clogged Spray Gun – If the spray gun is not cleaned immediately after use, dried paint can clog it.
2. Thick Paint Mixture – If the paint is too thick, the gun may not be able to atomize it properly.
3. Improper Gun Setup – Incorrect setup, including tip size, air pressure, or distance from the surface, can affect paint flow.
4. Inadequate Solvent – If the paint is not properly mixed with the correct solvent, it may not flow through the sprayer.
5. Drying Too Quickly – If the paint dries too fast before exiting the sprayer, it may block the nozzle.
Proper cleaning, correct paint viscosity, and proper setup can help resolve these issues.
This answer is automatically generated
missing the spray gun for a 44677 unit is it worth to buy if available or scrap the whole unit