Subscribe to Our Youtube Channel
Related Manuals for Walkdesk WTB500
Summary of Contents for Walkdesk WTB500
- Page 1 WALKDESK TREADMILL WTB500 OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW TREADMILL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions Important Electrical Instructions Grounding Instructions Important Operation Instructions Assembly Instructions Console Operation General Maintenance Service Checklist – Diagnosis guide Treadmill Exploded View Diagram/Parts List ATTENTION This treadmill is intended for residential use only and is warranted for this application. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING : Read all instructions before using this appliance. DANGER : To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to cleaning and/or service work. WARNING : To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 230~volt, 10-amp grounded outlet with only the treadmill plugged into the circuit. -
Page 4: Important Electrical Instructions
IMPORTANT ELECTRICAL INSTRUCTIONS WARNING! NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any appliance with a large motor, the GFCI will trip often. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. -
Page 5: Important Operation Instructions
IMPORTANT OPERATION INSTRUCTIONS • NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. • Understand that changes in speed and incline do not occur immediately. Set your desired work level on the computer console and release the adjustment key. -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTIONS !!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. - Page 7 1. Through the Computer Cable (62) to the Console Bracket Assembly (82). 2. Slide Computer Cable (62), use Phillips Head Screw Driver (89) to tighten 4pcs of M5 × 12L Phillips Head Screws (88) to secure Console Assembly (53) on Console Bracket Assembly (82). HARDWARE #88.
-
Page 8: Console Operation
OPERATION OF YOUR CONSOLE GETTING FAMILIAR WITH THE CONTROL PANEL INITIAL DISPLAY When the power is turned on, main window will bright and show all parameter, then show the current software version, how many hours the treadmill has been in use and how many Kilometers (or Miles if the treadmill is set to imperial readings), above each data will be shown for 2 seconds in order, the treadmill has gone. - Page 9 FUNCTION BUTTON ENTER: Press ENTER button to set the parameter of count down. When the belt stop running which press an hold this button for 3 seconds to reset all data which is the parameter value of accumulating. To confirmer stride length setting. START: Press START button to begin training.
-
Page 10: General Maintenance
GENERAL MAINTENANCE BELT/DECK Your treadmill uses a very high-efficient low-friction deck. Performance is maximized when the deck is kept as clean as possible. Use a soft, damp cloth, or paper towel, wipe the edge of the belt and the area between the belt edge and the frame. - Page 11 TREADBELT TRACKING ADJUSTMENT The treadmill is designed so that the tread-belt remains reasonably centered while in use. It is normal for some belts to drift near one side while in use, depending on a user’s gait and if they favor one leg. But if during use the belt continues to move toward one side, adjustments are necessary.
- Page 12 BELT/DECK LUBRICATION PROCEDURE not lubricate with other than approved lubricant. Your treadmill comes with one tube of lubricant and extra tubes can be ordered directly from your authorized dealer. There are commercially available lube kits. The proper kit should be silicon based, NOT paraffin wax. Keeping the deck lubricated at the recommended intervals ensures the longest lifepossible for your treadmill.
-
Page 13: Service Checklist - Diagnosis Guide
SERVICE CHECKLIST - DIAGNOSIS GUIDE Before contacting your dealer for aid, please review the following information. It may save you both time and expense. This list includes common problems that may not be covered under the treadmill’s warranty. PROBLÈME SOLUTION/CAUSE 1. -
Page 14: Treadmill Exploded View Diagram/Parts List
TREADMILL EXPLODED VIEW DIAGRAM... - Page 15 TREADMILL PARTS LIST Dwg # Part description Main Frame 3/8" × 7T_Nut Ø35 × 10m/m_Rubber Foot Transportation Wheel, Ø54 5/16" × UNC18 × 42L_Button Head Socket Bolt 5/16 × 6T_Nyloc Nut Cushion Running Belt Drive Belt Front Roller W/Pulley Rear Roller Running Deck M8 ×...
- Page 16 Dwg # Part description 5 × 16m/m_Tapping Screw Ø3/8" × Ø19 × 1.5T_Flat Washer 3/8" × 2"_Flat Head Socket Bolt 5 × 19m/m_Tapping Screw 3 × 8m/m_Sheet Metal Screw Controller Back Plate Generator/Brake Controller Console Assembly Bottom Connecting Filter Generator/Brake Controller Safety Key T31 ×...
- Page 17 Stadsheide 3 - 3500 Hasselt - Belgium +32 11 76 12 70 - info@evowalkdesk.com www.evowalkdesk.com...
Need help?
Do you have a question about the WTB500 and is the answer not in the manual?
Questions and answers