Troubleshooting Guide - PROFIX TRYTON TUV12BK2 Operating Instructions Manual

To remove a drill (or a working bit) from the chuck hold the lower ring of
the grip (the one close to the tool body) with one hand and rotate, with
the other hand, the upper ring anticlockwise to enlarge the chuck
opening.
Drilling boreholes
n
1. To drill deep boreholes carry out your job gradually, drill to lower
depths and remove the drill from the borehole from time to time to
remove borings from the borehole.
2. To drill large diameter boreholes it is recommended to start with
drilling a low-diameter borehole and then expand it to the desired
diameter. It prevents the tool from overloads.
3. When the drilling bit is seized during working switch immediately
tool off to prevent it from being damaged. Switch the rotations
direction to the anticlockwise rotations and then remove the drilling
bit from the borehole.
4. Keep the drill aligned with the axis of the borehole. The drilling bit
must be positioned perpendicularly to the surface of the machined
material. When the perpendicularity fails to be maintained the
drilling bit may be seized or broken or, under extreme circumstances,
the operator may be injured.
Rotation speed of the drill spindle is controlled by the force the power
switch is depressed with.
Driving screws
n
It is recommended to drill the pilot borehole first. The pilot borehole must
be a little deeper and with a less diameter than the outer diameter of the
screw thread. When the screw is to be driven within the vicinity of the
material edge the pilot borehole prevents from undesired chipping of the
material.
If the screw is driven with abnormal difficulty the screw must be
retracted and the pilot borehole diameter should be enlarged.
Anyway, when problem to drive the screw in persists (e.g. in case of hard
wood grades) try to use a lubricating agent (e.g. liquid soap). Press the
tool to the screw with sufficient force to avoid spontaneous rotation of
the driving bit in the screw head. Use only those bits that accurately
match the bit head. When the screw head is damaged further driving the
screw in or out may prove infeasible.
STORAGE AND MAINTENANCE:
The tool in principle does not require any special maintenance or service.
The tool must be stored in a place that is not accessible to children and
must be kept clean and protected from moisture and dust. The storage
conditions should prevent potential mechanical damage and impact of
the weather conditions.
Clean the tool pursuant to maintenance schedule. Remember to always
disconnect the battery from the tool prior to starting the cleaning
operations and unplug the charger from the outlet.
The charger may be cleaned exclusively with use of a dry cloth. Use also a

TROUBLESHOOTING GUIDE:

PROBLEM
The tool (drill/screwdriver)
fails to operate.
Irregularities of the motor
operation.
POSSIBLE CAUSE
No power voltage, damaged
motor or the power trigger.
Battery low.
Worn carbon brushes of the motor. Have the brushes replaced at a service workshop.
clean cloth to clean regularly the ventilation openings of the tool to keep
them patent. From time to time disassemble the grip and remove dust
and other rubbish from the interior.
The tool housing must be cleaned with use of a moistened cloth
quantity of soap and then wiped dry. Do not use any detergents or
solvents as they can damage parts made from plastics.
the tool dry completely before it is used again.
TRANSPORTATION:
Store and transport the tool in its transport box to protect it against
humidity, dust penetration and small objects; remember to protect its
ventilation openings. Small objects after getting into the casing can
result in damage to the motor.
MANUFACTURER:
Sp. z o.o.
PROFIX ,
ul. Marywilska 34, 03-228 Warszawa, POLAND.
This appliance is in conformity with national and European standards as
well as with general safety guidelines.
Any repairs are allowed to be carried out exclusively by qualified staff
with use of original spare parts.
PICTOGRAMS:
Explanation of the icons located on the nominal plate and the
information tags:
«Read this instruction before switching on the
power supply and starting the work»
« Always wear appropriate eye protection
« Use appropriate hearing protection
PROTECTION OF THE ENVIRONMENT:
NOTE: The symbol nearby denotes that old equipment must
never be thrown away together with other waste (with the
penalty of a fine). Hazardous components of electronic
equipment may adversely affect the natural environment and
human health.
Each household may contribute to the recovery and reuse (recycling) of
old machinery and equipment. Both in Poland and Europe a system for
recovery of used equipment either exists or is being created. The system
obliges all organizations that sell such equipment to collect the used
machinery and appliances. Moreover, general purpose collecting points
for suh equipment are available.
Check the battery status, recharge or replace with a new one when necessary.
When the problem persists hand over the tool for repair at a service workshop.
Please refer to the warranty sheet for addresses of authorized workshops.
Recharge the battery.
7
After cleaning let
»
REMEDY
small
»