SERVICE MANUAL COLOUR TELEVISION YA416 2006 AV-2106BE, AV-21B16 AV-21BMG6B , AV-21BMG6 BASIC CHASSIS TABLE OF CONTENTS PRECAUTION............... . . 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
SPECIFICATION Items Contents AV-2106BE AV-21B16/L AV-21BMG6B/G AV-21BMG6/G Dimensions (W × H × D) 59.8 cm × 47.6 cm × 47.7 cm Mass 22 kg TV RF System B/G, I, D/K B/G, I, D/K, M Colour System SECAM SECAM NTSC3.58/NTSC4.43 Receiving VHF Low 46.25 MHz to 140.25 MHz Frequency...
SECTION 1 PRECAUTION SAFETY PRECAUTIONS (1) The design of this product contains special hardware, (8) When service is required, observe the original lead dress. many circuits and components specially for safety Extra precaution should be given to assure correct lead purposes.
SECTION 2 SPECIFIC SERVICE INSTRUCTIONS FEATURES PICTURE MODE CHILD LOCK This function can adjust the picture settings automatically. Use this function to prevent children from operating the TV There are BRIGHT, STANDARD and SOFT in the PICTURE without parental consent. MODE.
SECTION 3 DISASSEMBLY DISASSEMBLY PROCEDURE 3.1.1 REMOVING THE REAR COVER • Unplug the power cord. (1) Remove the 6 screws [A], 1 screw [B] and 1 screw [C] as shown in Fig.1. (2) Withdraw the REAR COVER toward you. CAUTION: When reinstalling the rear cover, carefully push it inward after inserting the MAIN PWB into the REAR COVER groove.
Page 6
FRONT CABINET SPEAKER CRT SOCKET PWB (Within MAIN PWB) FRONT LED PWB (Within MAIN PWB) POWER CORD SPEAKER MAIN PWB REAR COVER Fig.1 1-6 (No.YA416)
Page 7
MEMORY IC REPLACEMENT • This model uses the memory IC. • This memory IC stores data for proper operation of the video and drive circuits. • When replacing, be sure to use an IC containing this (initial value) data. 3.2.1 MEMORY IC REPLACEMENT PROCEDURE 1.
Page 8
3.2.2 SETTINGS OF FACTORY SHIPMENT 3.2.2.1 BUTTON OPERATION 3.2.3 SYSTEM CONSTANT SETTING Setting item Setting position Setting value Setting item POWER AV-2106BE AV-21B16/L AV-21BMG6B/G AV-21BMG6/G ← ← CHANNEL COLOUR TRIPLE MULTI ← ← ← VOLUME BILINGUAL ← ← ← TUNER 3.2.2.2 REMOTE CONTROL DIRECT OPERATION ←...
Page 9
3.2.4 SERVICE MENU SETTING ITEMS Setting item Setting value Setting item Setting value 2. V/C 1.CUT OFF 5. PRESET Colour System 1. C-TRAP FIX 2.DRIVE [Do not adjust] 2. SHARP PEAK 3.BRIGHT 3. ABL 4.CONT. 4. GAMMA 5.COLOUR 5. Y. DELAY TIME 6.TINT 6.
Page 10
REPLACEMENT OF CHIP COMPONENT 3.3.1 CAUTIONS (1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it. 3.3.2 SOLDERING IRON (1) Use a high insulation soldering iron with a thin pointed end of it.
SECTION 4 ADJUSTMENT ADJUSTMENT PREPARATION MEASURING INSTRUMENT AND FIXTURES (1) There are 2 ways of adjusting this TV : One is with the (1) DC voltmeter (or digital voltmeter) REMOTE CONTROL UNIT and the other is the (2) Oscilloscope conventional method using adjustment parts and (3) Signal generator components.
Page 13
BASIC OPERATION OF SERVICE MENU 4.6.1 TOOL OF SERVICE MENU OPERATION Operate the SERVICE MENU with the REMOTE CONTROL UNIT. 4.6.2 SERVICE MENU ITEMS With the SERVICE MENU, various adjustments can be made, and they are broadly classified in the following items of settings. 1.IF Adjustment of the IF circuits.
Page 14
(1) By pressing the [6] key, you can change the ON or OFF [should be OFF]. Should be OFF: If it is ON, when you turn off the power and turn on a power again, the JVC’s logo will be shown about 15 seconds automatically, and the SETUP TOUR starts.
Page 15
4.6.8 SERVICE MENU FLOW CHART SERVICE MENU 1. IF VCO (CW) ***.** TOO HIGH SERVICE MENU ABOVE REFERENCE 1.IF 2.V/C JUST REFERENCE 3.DEF 4.VSM PRESET BELOW REFERENCE 1. VCO 5.PRESET TOO LOW 6.SETUP TOUR OFF AFT ADJUST 2. DELAY POINT VCO ADJUST 1-6 : SELECT DISP : EXIT...
Page 16
INITIAL SETTING VALUE OF SERVICE MENU • Adjustment of the SERVICE MENU is made on the basis of the initial setting values ; however, the new setting values which set the screen in its optimum condition may differ from the initial setting. •...
Page 18
[5. PRESET] The items in the following table, it is no requirement for adjustment.If values had changed by the miss operation, set the initial setting values in the following table. COLOUR SYSTEM (Do not adjust) [AV-2106BE, AV-21B16/L] Initial setting value (Fixed value) Setting item Variable range SECAM...
Page 19
[AV-21BMG6B/G, AV-21BMG6/G] Initial setting value (Fixed value) Setting item Variable range SECAM NTSC 3.58 NTSC 4.43 1. C TRAP FIX 0 - 1 2. SHARP PEAK 0 - 1 3. ABL 0 - 1 4. GAMMA 0 - 1 5. Y. DELAY TIME 0 - 3 VIDEO 0 - 3...
Page 20
ADJUSTMENT PROCEDURE 4.8.1 CHECK ITEM Measuring Item Test point Adjustment part Description instrument B1 VOLTAGE Signal TP-B1 : 1-pin (1) Receive a whole black signal. generator TP-E : 5-pin (2) Connect a DC voltmeter to 1-pin and 5-pin of S1 (S1 connector) connector.
Page 21
Measuring Item Test point Adjustment part Description instrument DELAY POINT Signal [1. IF] (1) Receive a black and white signal (colour off). (AGC) generator 2. DELAY POINT (2) Select 1. IF. (AGC TAKE-OVER) (3) Select < 2. DELAY POINT >. Remote (4) Set the setting values of the setting items as shown control unit...
Page 22
4.8.4 DEFLECTION CIRCUIT • There are 2 modes of adjustment (setting value) 50Hz mode and 60Hz mode, depending upon the kind of signals (vertical frequency 50Hz / 60Hz). • When adjusted in 50Hz mode and 60Hz mode will be automatically set. The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
Page 23
4.8.5 VIDEO CIRCUIT The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values. Do not change the initial setting values of the setting items not listed in "ADJUSTMENT PROCEDURE".
Page 24
Measuring Item Test point Adjustment part Description instrument SUB COLOUR Remote [2. V/C] [Method of adjustment without measuring instrument] control unit 5. COLOUR PAL COLOUR (PAL / SECAM / NTSC) (1) Receive a PAL broadcast. (2) Select 2. V/C from the SERVICE MENU. (3) Select <...
Page 25
Measuring Item Test point Adjustment part Description instrument SUB TINT Signal [2. V/C] [Method of adjustment without measuring instrument] generator 6. TINT NTSC 3.58 TINT (1) Receive a NTSC 3.58 full field colour bar signal Remote (75% white). control unit (2) Select 2.
Page 26
Measuring Item Test point Adjustment part Description instrument SECAM BLACK Signal [2. V/C] (1) Input a SECAM full field colour bar signal. OFFSET generator 7. SECAM BL ADJUST (2) Select 2. V/C from the SERVICE MENU. (3) Select < 7. SECAM BL ADJUST >. Remote (4) Set the initial setting value of <...
Page 27
4.8.7 PURITY AND CONVERGENCE PURITY ADJUSTMENT Note: The final adjustment of CONVERGENCE must be done after WEDGE DEFLECTION the FOCUS adjustment. (CONVERGENCE is changed by YOKE FOCUS adjustment.) When makes difference by FOCUS adjustment, should be reconfirming PURITY adjustment. (1) Demagnetize CRT with the demagnetizer. P / C (2) Loosen the retainer screw of the deflection yoke.
STATIC CONVERGENCE ADJUSTMENT (1) Input a crosshatch signal. (2) Using 4-pole convergence magnets, overlap the red and (FRONT VIEW) blue lines in the centre of the screen (Fig.1) and turn them to magenta (red/blue). (3) Using 6-pole convergence magnets, overlap the magenta (red/blue) and green lines in the centre of the screen and turn them to white.
Page 29
Victor Company of Japan, Limited Display Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan (No.YA416) Printed in Japan...
Page 30
1 Confirm which remote control you have ..3 INSTRUCTIONS 2 Inserting the batteries ........3 3 Connecting the aerial and external devices ... 4 Thank you for buying this JVC 4 Connecting the power cord ......6 colour television. 5 SETUP TOUR ..........6...
Safety precautions WARNING • To prevent fire or shock hazard, do not expose the TV to rain or moisture. CAUTION • Operate only from the power source indicated on the rear of the TV. • Avoid damaging the power cord and mains plug. When you unplug the TV, pull it out by the mains plug.
Preparation 1 Confirm which remote control you have RM-C360GY POWER SYSTEM PICTURE COLOUR SOUND MODE TV/VIDEO TIMER CHANNEL RETURN - / -- SCAN DISPLAY MUTING MENU CHANNEL VOLUME REMOTE CONTROL UNIT RM-C360GY 2 Inserting the batteries Correctly insert two batteries, observing the , and .
Preparation 3 Connecting the aerial and external devices • For further details, refer to the manuals provided with the devices you are connecting. • Connecting cables are not supplied. • The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either jack is output through both.
Page 34
Preparation ■ Connecting other external devices To audio To video output output VCR (for playing) VIDEO AUDIO (VIDEO - 1) VCR (for recording) To audio To video input input • Illustration of AV-14A16. Camcorder TV game To video To audio output output VIDEO...
Operate only from the power source indicated on the rear of the TV. 5 SETUP TOUR When the TV is first turned on it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR.
Basic operation 1 Press the POWER button to turn your TV on. • If your TV does not turn on, press the POWER Main power button on the TV then press SYSTEM PICTURE the POWER button again. COLOUR SOUND MODE •...
Remote control buttons and functions In VIDEO mode: PICTURE MODE button AUTO SECAM You can select one of three picture adjustment settings as you like. NTSC3.58 NTSC4.43 Press this button to select a mode. AUTO: Automatic colour system selection. BRIGHT: Heightens contrast and sharpness.
Remote control buttons and functions DISPLAY button CHANNEL SCAN button You can continuously display the current You can quickly view all TV channels channel number or VIDEO mode on the programmes that you can view on your screen. TV, and search for the programme you want to view.
Using the TV’s menus This TV has a number of functions you can operate using the menus. To use all your TV’s functions fully, you need to understand how to use the menus. 2 Repeatedly press the MENU T buttons to display a desired menu.
Using the TV’s menus When the time set for the ON TIMER ON TIMER function is reached: Your TV will automatically turn on and The TV automatically turns on and the tune into the channel you set after the channel set for the ON TIMER function is period of time you set.
Using the TV’s menus CHILD LOCK (Video Noise Reduction) You can reduce the picture noise. You can disable the front control buttons of the TV. 1 Press MENU T to display the When this function is set to “ON”, the TV “MENU 1”...
EXIT BY 2 Press MENU M. OPERATE BY -+ D I SPLA Y JVC logo is appear and the SETUP 2 Press MENU M to start the AUTO TOUR function will start. CH PRESET function. For details, see page 6.
Using the TV’s menus If the picture is not clear: MANUAL CH PRESET Fine-tune the TV channel. You can manually preset desired TV channels to desired channels. 1 Press MENU t to select “FINE”. 1 Press MENU T to display the MANUAL FINE “MENU 3”...
Using the TV’s menus SKIP Picture Adjustments You can set undesired channels to be You can adjust the picture as you like. skipped. Channels set to be skipped 1 Press MENU T to display the cannot be selected by the CHANNEL m “MENU 4”...
Using the buttons on the TV <AV-14F16> 1 MENU button • MENU button 2 CHANNEL m buttons MENU CHANNEL VOLUME ON TIMER POWER • MENU m buttons EXIT 3 VOLUME m buttons • EXIT from MENU buttons 4 Remote control sensor <AV-14A16>...
Page 46
Using the buttons on the TV Basic operation Operating menus • Check to make sure the CHILD LOCK You can operate functions in menus using function is set to “OFF”. When the CHILD the front control buttons on the TV. LOCK function is set to “ON”, the TV cannot 1 Press MENU y to display a menu.
Troubleshooting If there is no picture or the TV does not operate normally, make sure the problem isn’t due to the reasons indicated below. If the problem persists even after taking the measures indicated, please contact a service technician. Poor picture Cannot turn the TV on •...
Specifications TV RF systems B, G, I, D, K, K1 Colour systems PAL, SECAM, NTSC 3.58 MHz/NTSC 4.43 MHz (in VIDEO mode only) Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band. External input / output INPUT: VIDEO input (RCA), AUDIO input (RCA)
Page 50
1 Confirm which remote control you have ..3 INSTRUCTIONS 2 Inserting the batteries ........3 3 Connecting the aerial and external devices ... 4 Thank you for buying this JVC 4 Connecting the power cord ......6 colour television. 5 SETUP TOUR ..........6...
Safety precautions WARNING • To prevent fire or shock hazard, do not expose the TV to rain or moisture. CAUTION • Operate only from the power source indicated on the rear of the TV. • Avoid damaging the power cord and mains plug. When you unplug the TV, pull it out by the mains plug.
Preparation 1 Confirm which remote control you have RM-C360GY POWER SYSTEM PICTURE COLOUR SOUND MODE TV/VIDEO TIMER CHANNEL RETURN - / -- SCAN DISPLAY MUTING MENU CHANNEL VOLUME REMOTE CONTROL UNIT RM-C360GY 2 Inserting the batteries Correctly insert two batteries, observing the , and .
Preparation 3 Connecting the aerial and external devices • For further details, refer to the manuals provided with the devices you are connecting. • Connecting cables are not supplied. • The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either jack is output through both.
Page 54
Preparation ■ Connecting other external devices To audio To video output output VIDEO AUDIO VCR (for playing) VCR (for recording) To audio To video input input • Illustration of AV-14FMG6B. Camcorder TV game To video To audio To video To audio output output output...
Operate only from the power source indicated on the rear of the TV. 5 SETUP TOUR When the TV is first turned on it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR.
Basic operation 1 Press the POWER button to turn your TV on. • If your TV does not turn on, press the POWER Main power button on the TV then press SYSTEM PICTURE the POWER button again. COLOUR SOUND MODE •...
Remote control buttons and functions In VIDEO mode: PICTURE MODE button AUTO SECAM You can select one of three picture adjustment settings as you like. NTSC3.58 NTSC4.43 Press this button to select a mode. AUTO: Automatic colour system selection. BRIGHT: Heightens contrast and sharpness.
Remote control buttons and functions DISPLAY button CHANNEL SCAN button You can continuously display the current You can quickly view all TV channels channel number or VIDEO mode on the programmes that you can view on your screen. TV, and search for the programme you want to view.
Using the TV’s menus This TV has a number of functions you can operate using the menus. To use all your TV’s functions fully, you need to understand how to use the menus. 2 Repeatedly press the MENU T buttons to display a desired menu.
Using the TV’s menus When the time set for the ON TIMER ON TIMER function is reached: Your TV will automatically turn on and The TV automatically turns on and the tune into the channel you set after the channel set for the ON TIMER function is period of time you set.
Using the TV’s menus CHILD LOCK (Video Noise Reduction) You can reduce the picture noise. You can disable the front control buttons of the TV. 1 Press MENU T to display the When this function is set to “ON”, the TV “MENU 1”...
EXIT BY 2 Press MENU M. OPERATE BY -+ D I SPLA Y JVC logo is appear and the SETUP 2 Press MENU M to start the AUTO TOUR function will start. CH PRESET function. For details, see page 6.
Using the TV’s menus If the picture is not clear: MANUAL CH PRESET Fine-tune the TV channel. You can manually preset desired TV channels to desired channels. 1 Press MENU t to select “FINE”. 1 Press MENU T to display the MANUAL FINE “MENU 3”...
Using the TV’s menus SKIP Picture Adjustments You can set undesired channels to be You can adjust the picture as you like. skipped. Channels set to be skipped 1 Press MENU T to display the cannot be selected by the CHANNEL m “MENU 4”...
Using the buttons on the TV The following illustrations are of only some models are shown for explanation purpose only. Your TV may not be exactly the same as illustrated. <AV-14AG16> 1 MENU button MENU CHANNEL VOLUME POWER / • MENU button ON TIMER 2 CHANNEL m buttons...
Page 66
Using the buttons on the TV Basic operation Operating menus • Check to make sure the CHILD LOCK You can operate functions in menus using function is set to “OFF”. When the CHILD the front control buttons on the TV. LOCK function is set to “ON”, the TV cannot 1 Press MENU y to display a menu.
Troubleshooting If there is no picture or the TV does not operate normally, make sure the problem isn’t due to the reasons indicated below. If the problem persists even after taking the measures indicated, please contact a service technician. Poor picture Cannot turn the TV on •...
Specifications TV RF systems B, G, I, D, K, K1, M Colour systems PAL, SECAM, NTSC 3.58 MHz/NTSC 4.43 MHz Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band. External input / output INPUT: VIDEO input (RCA), AUDIO input (RCA)
Page 70
О К ........ 6 5 О Д С Дякуємо Вам за придбання цього Основне керування кольорового телевізора JVC. Кнопки пульту дистанційного керування Щоб переконатися в тому, що Ви вмієте та їх функції користуватися Вашим новим телевізором, будь ласка, спочатку Кнопка PICTURE MODE ......... 8 К...
до / від розетки змінного струму. Встановлюючи телевізор, залишіть навколо нього достатній простір для приєднання/від’єднання штепсельної вилки до / від розетки змінного струму за допомогою руки. Компанія JVC встановлює термін служби виробів JVC, що дорівнює 7 рокам, за умови дотримання правил експлуатації. Eксплуатацїю даного виробу може бути продовжено після...
Підготовка 1 Перевірте, яку модель пульту дистанційного керування Ви маєте RM-C360GY REMOTE CONRTOL UNIT RM-C360GY 2 Вставлення батарей Правильно вставте дві батареї, звертаючи увагу на розташування полюсів , та . і вставляючи спочатку кінець з позначкою .. ОБЕРЕЖНО: Дотримуйтесь правил користування, вказаних на батарейках.
Підготока 3 Приєднання антени та зовнішніх пристроїв • За більш детальною інформацією звертайтеся до інструкцій користувача, що поставляються з пристроями, які Ви приєднуєте. • Кабелі для приєднання не включені до комплекту. • Передні та задні вхідні гнізда AUDIO/VIDEO з’єднані напряму таким чином, що вхідний сигнал для будь- якого...
Page 74
Підготовка ■ Приєднання інших зовнішніх пристроїв До До аудіовиходу відеовиходу VIDEO AUDIO Відеомагнітофон (для програвання) Відеомагнітофон (для запису) До До аудіовходу відеовходу • Зображення моделі AV-2106TE До Відеокамера відеовиходу або До аудіовиходу телевізійна ігрова приставка MENU VIDEO AUDIO Навушники • Зображення моделі AV-2106TE. •...
С О К Під час першого ввімкнення телевізору, він перейде в режим О Д С О К і на екрані з’явиться логотип компанії JVC. Щоб виконати розділ О Д С О К , дотримуйтесь інструкцій на екрані. • У випадку зміни установок, наприклад з причини видалення, Ви можете...
Основне керування 1 Натисніть кнопку POWER, щоб ввімкнути Ваш телевізор. • Якщо Ваш телевізор не ввімкнеться, натисніть головну кнопку живлення на телевізорі, потім ще раз натисніть кнопку POWER. • Ви також можете ввімкнути Ваш телевізор, натиснувши будь-яку з зазначених нижче кнопок; - кнопку...
Кнопки пульту дистанційного керування та їх функції Кнопка PICTURE MODE В режимі VIDEO: Ви можете вибрати одну з трьох установок режиму зображення за Вашим бажанням. О: Натисніть цю кнопку для вибору Автоматичний вибір системи кольору. режиму. СК • Що стосується систем кольору у кожній країні...
Кнопки пульту дистанційного керування та їх функції Кнопка DISPLAY Кнопка CHANNEL SCAN Ви можете швидко переглянути Ви можете ввімкнути постійне програми всіх телеканалів, які може відображення номеру поточного каналу, приймати Ваш телевізор, а також Д О. або режиму знайти програму, яку хочете Натисніть...
Користування меню телевізора Цей телевізор має декілька функцій, якими Ви можете керувати за допомогою меню. Для повного використання всіх функцій телевізора Вам необхідно зрозуміти, як користуватися меню. 2 Натисніть кілька разів кнопки MENU T, щоб вивести потрібне меню . • Якщо Ви будете утримувати кнопку y, буде...
Page 80
Користування меню телевізора КЛ Якщо був досягнутий час, встановлений для функції Ваш телевізор автоматично КЛ: ввімкнеться і налаштується на Телевізор автоматично ввімкнеться і встановлений канал після закінчення на екран буде виведений канал, встановленого періоду часу. встановлений для функції КЛ. 1 Скористайтесь кнопками MENU T, щоб...
Користування меню телевізора БЛОКУ VNR (Система зниження відеошуму) Ви можете зменшити шум зображення. Ви можете заблокувати кнопки керування на передній панелі 1 Скористайтесь кнопками MENU телевізора. T, щоб вивести на екран меню Коли ця функція встановлена в 1” , а потім виберіть опцію положення...
Користування меню телевізора БЛ К К Якщо телевізійний сигнал не приймається або є нестабільним, телевізор може вимкнути звук і змінити зображення на синій екран. 1 Скористайтесь кнопками MENU T , щоб вивести на екран меню 2” , а потім виберіть опцію “...
3” , а потім виберіть опцію “ О С О К ” . “ 2 Натисніть кнопки MENU -/+. На екрані з’явиться логотип компанії JVC і запуститься функція О Д С О К . 2 Скористайтесь кнопками MENU -/+ О для запуску функції “...
Користування меню телевізора У С О К Якщо зображення є нечітким: Проведіть точне налаштування Ви можете вручну призначити потрібні телеканалу. телеканали на бажані канали. 1 Скористайтесь кнопками MENU t, щоб вибрати опцію “ О ” 1 Скористайтесь кнопками MENU T, щоб вивести на екран меню 3”...
Користування меню телевізора О УСК Регулювання зображення Ви можете встановити функцію Ви можете відрегулювати зображення пропуску для каналів, які не бажаєте за власним бажанням. переглядати. Канали, для яких була 1 Скористайтесь кнопками MENU встановлена функція пропуску, не T, щоб вивести на екран меню можуть...
Користування кнопками на телевізорі На наступному малюнку зображені окремі моделі лише з метою роз’яснення. Ваш телевізор може відрізнятися від зображених. 1 Кнопка MENU <AV-2106YE> • Кнопка MENU 2 Кнопки CHANNEL –/+ • Кнопки MENU –/+ 3 Кнопки VOLUME –/+ ON TIMER POWER •...
Page 87
Користування кнопками на телевізорі Основне керування Керування меню Ви можете керувати функціями меню • Переконайтеся в тому, що функція БЛОКУ за допомогою кнопок керування на встановлена у положення КЛ” . “ передній панелі телевізора . Коли функція БЛОКУ встановлена 1 Натисніть кнопку MENU y, щоб в...
Пошук несправностей Якщо на екрані немає зображення або телевізор не працює належним чином перевірте, чи не виникла проблема через перелічені нижче причини. Якщо проблема залишиться навіть після запровадження вказаних заходів, будь ласка, зверніться до спеціаліста з технічного обслуговування. Телевізор неможливо ввімкнути Нечітке...
Технічні характеристики Високочастотні системи звуку B, G, I, D, K, K1 Системи кольору PAL, SECAM, NTSC 3.58/4.43 МГц (лише в режимі VIDEO) Канали, що можуть прийматися Канали нижнього діапазону коротких хвиль VHF (VL), канали верхнього діапазону коротких хвиль VHF (VH), канали ультракоротких...
Page 90
PARTS LIST CAUTION The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the safety. The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied. P.W.
Page 91
A51MBA11X05AN05 PICTURE TUBE(ITC) Inc.DEF YOKE, PC MAGNET AV-21B16L,AV-21BMG6G,AV-21BMG6BG L01 QQW0125-001 DEG COIL T522 QQH0170-001 FB TRANSF GG30152-001A-H JVC MARK GG30150-002A-H OPERATION SHEET GG30149-001A-H LED LENS QYSBSFG4016ZA TAP SCREW M4 x 16mm(x6) QYSBSF3010ZA TAP SCREW M3 x 10mm QYSBSFG4016ZA...
PRINTED WIRING BOARD PARTS LIST [AV-2106BE] MAIN P.W. BOARD ASS'Y (SCG-1549A-H2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C005 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J C008 QETN1HM-475Z E CAPACITOR 4.7uF 50V M IC301 NN5198K C010...
Page 94
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C655 QETN1HM-106Z E CAPACITOR 10uF 50V M R314 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J C656 QENC1HM-105Z BP E CAPACITOR 1uF 50V M R321 NRSA63J-152X MG RESISTOR 1.5kΩ...
Page 95
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R709 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J K941 QQR1113-001Z FERRITE BEADS R710 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J K942 QQR1113-001Z FERRITE BEADS R711 NRSA63J-472X MG RESISTOR 4.7kΩ...
PRINTED WIRING BOARD PARTS LIST [AV-21B16/L] MAIN P.W. BOARD ASS'Y (SCG-1547A-H2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C005 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J C008 QETN1HM-475Z E CAPACITOR 4.7uF 50V M IC301 NN5198K C010...
Page 97
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C655 QETN1HM-106Z E CAPACITOR 10uF 50V M R314 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J C656 QENC1HM-105Z BP E CAPACITOR 1uF 50V M R321 NRSA63J-152X MG RESISTOR 1.5kΩ...
Page 98
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R709 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J K902 QQR1113-001Z FERRITE BEADS R710 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J K941 QQR1113-001Z FERRITE BEADS R711 NRSA63J-472X MG RESISTOR 4.7kΩ...
PRINTED WIRING BOARD PARTS LIST [AV-21BMG6/G, AV-21BMG6B/G] MAIN P.W. BOARD ASS'Y (SCG-1548A-H2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C001 QETN1HM-106Z E CAPACITOR 10uF 50V M C002 NCB31HK-103X C CAPACITOR 0.01uF 50V K IC301 NN5198K C004...
Page 100
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C571 QETN1AM-107Z E CAPACITOR 100uF 10V M R161 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J C572 QETN1EM-476Z E CAPACITOR 47uF 25V M R162 NRSA63J-122X MG RESISTOR 1.2kΩ...
Page 101
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R655 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J L942 QQL244J-4R7Z PEAKING COIL 4.7uH J R656 NRSA63J-822X MG RESISTOR 8.2kΩ 1/16W J L943 QQL244J-4R7Z PEAKING COIL 4.7uH J R657 NRSA63J-222X...
REMOTE CONTROL UNIT PARTS LIST (RM-C360GY-1H) Ref No. Part No. Part Name Description Local R25-8567 BATTERY COVER PACKING PACKING PARTS LIST Ref.No. Part No. Part Name Description Local GG10285-012A-H PACKING CASE AV-2106BE,AV-21B16L GG10282-044A-H PACKING CASE AV-21BMG6G,AV-21BMG6BG GG10422-001A-H CUSHION ASS'Y 5pcs in 1set GG30097-003B-H POLY BAG...
Page 104
AV-2106BE, AV-21B16 , AV-21BMG6B , AV-21BMG6 STANDARD CIRCUIT DIAGRAM NOTE ON USING CIRCUIT DIAGRAMS 1.SAFETY Type The components identified by the symbol and shading are No indication : Ceramic capacitor critical for safety. For continued safety replace safety ciritical : Metalized mylar capacitor : Polypropylene capacitor components only with manufactures recommended parts.
BLOCK DIAGRAM MAIN PWB(1/3, 2/3) POWER LED STB_PW IC703 5V REG.& RESET TIMER LED SF102 TU001 Q102 LED(TIM) IF AMP SAW FILTER TUNER REMOCON REMOCON RECEIVER SCL/SDA HEADPHONE IC651 SPEAKER L AUDIO AMP AUDIO OUT SCL/SDA SCL/SDA SPEAKER R IC701 IC702 MAIN PWB(3/3) MEMORY...
VOLTAGE CHARTS <MAIN PWB> <CRT SOCKET PWB> MODE MODE MODE MODE DC ( V ) DC ( V ) DC ( V ) DC ( V ) PIN NO. PIN NO. PIN NO. PIN NO. IC301 Q651 Q351 125.8 Q652 Q352 123.3 Q653...
Page 114
Victor Company of Japan, Limited Display Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan (No.YA416) Printed in Japan...