Advertisement
IDC-200 |
USER ManUal
SpECIfICatIonS
MoDEl
InpUt VoltaGE
no.
RanGE (VDC)
IDC-200A-12
9 - 18
IDC-200B-12
20 - 35
IDC-200C-12
30 - 60
IDC-200D-12
60 - 120
IDC-200A-24
9 - 18
IDC-200B-24
20 - 35
IDC-200C-24
30 - 60
IDC-200D-24
60 - 120
IDC-200B-48
20 - 35
IDC-200C-48
30 - 60
no loaD CURREnt DRaW
InpUt to oUtpUt ISolatIon
oUtpUt RIpplE & noISE
pEaK EffICIEnCY
CoolInG
opERatInG tEMpERatURE
anD DE-RatInG
HUMIDItY, non-ConDEnSInG
pRotECtIonS
SafEtY anD EMC StanDaRDS
eMissiONs
iMMuNiTy
AuTOMOTiVe DireCTiVe
InpUt / oUtpUt ConnECtIonS
DIMEnSIonS (W x D x H)
WEIGHt
NOTe: specifications are subject to change without notice
taBlE 1.
exTerNAL iNPuT siDe Fuse & WiriNg
MoDEl
fUSE SpECS
naME
IDC-200A-12, 24
32V, 30A
IDC-200B-12, 24, 48
58V, 15A
IDC-200C-12, 24, 48
80V, 10A
IDC-200D-12, 24
125V, 5A
taBlE 2.
exTerNAL OuTPuT siDe Fuse & WiriNg
MoDEl
fUSE SpECS
naME
IDC-200A-12
32V, 20A
IDC-200B-12
32V, 20A
IDC-200C-12
32V, 20A
IDC-200D-12
32V, 20A
IDC-200A-24
32V, 10A
IDC-200B-24
32V, 10A
IDC-200C-24
32V, 10A
IDC-200D-24
32V, 10A
IDC-200B-48
58V, 4A
IDC-200C-48
58V, 4A
notES foR taBlE 1 anD 2:
a) Wire sizes shown are based on 90oC / 194oF wire temperature rating and 2% voltage
drop over distance of up to 6' from battery or load for current = Amp rating of the fuse.
b) For distances > 6', use thicker wires to limit voltage drop to <2% for current =
Amp rating of the fuse.
tERMInatIon of ConnECtInG WIRES:
c) Use 6.3mm / 1/4" "Quick Connect", Female mating terminal on the connecting
wiring. This type of terminal is available for maximum wire size of AWG #10.
MaX InpUt
oUtpUt
CURREnt (a)
VoltaGE (VDC)
CURREnt (a)
<30
12.5
<15
12.5
<10
12.5
<5
12.5
<30
24.5
<15
24.5
<10
24.5
<5
24.5
<15
48.0
<10
48.0
< 25 mA
Yes. > 400V RMS
< 50 mV RMS
85%
By temperature controlled fan
-20 to +30oC / -4oF to 86oF
(De-rate linearly to zero at 70oC / 158oF)
Max 95%
Overload / short circuit on the output side;
Over voltage on the output side; Over voltage /
transients on the input side; Reverse polarity on
the input side; Over heating
EN55014-1
EN55014-2
UN Regulation ECE R10-4
Quick Connect ; Male, 6.3 mm /
1/4" flat blade
88.0 x 175.4 x 50 mm / 3.5 x 6.9 x 1.9 in
0.6 Kg / 1.4 lb
WIRE SIZE (Up to 6 ft from Battery)
(SEE notE 1 BEloW)
AWG#8
AWG#14
AWG#19
AWG#24
WIRE SIZE (Up to 6 ft from Battery)
(SEE notE 1 BEloW)
AWG#10
AWG#10
AWG#10
AWG#10
AWG#16
AWG#16
AWG#16
AWG#16
AWG#22
AWG#22
DIMEnSIonS & laYoUt
oUtpUt
20
5
20
20
20
10
10
10
10
4
4
5
lEGEnD [for figs. 2(a) and 2(b)]
1. Input + Terminal
2. Input – Terminal
3. Output – Terminal
4. Output + Terminal
5. Chassis Ground
6. Ventilation slots
7. Cooling fan (Exhausts outwards)
When using wires thicker than AWG #10, you may terminate the wire as
follows:
• U se 6.3mm / 1/4" "Quick Connect" Female matting connector (AWG #10 size)
• U se around 2" piece of AWG #10 wire and crimp the connector to one
end Solder / splice the other end of AWG #10 wire to wire the thicker wire
Use of short length of 2" of smaller AWG #10 wire will not increase voltage
drop appreciably.
175.4
168.0
• Height: 50 mm
• Use 4 mm bolt for mounting
NOTE: All measurements are in mm
Not to scale
Fig 1. Dimensions (Bottom View)
1
2
3
4
Fig 2(a). Layout (Front View)
6
7
Fig 2(b). Layout (Back View)
• Quick Connect Male Terminals
• 6.3 mm / 0.25" flat blade
DC-DC Converter Manual
58
88
6
| 3
Advertisement
