Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ecotech Marine Vortech MP10
Summary of Contents for Ecotech Marine Vortech MP10
- Page 1 MP10 MP10w *ESL integration requires ReefLink Setup Guide ® 060117...
-
Page 2: Table Of Contents
EcoTech Marine website at purchase of a VorTech MP10 ™ The EcoTech Marine Community is another tool for users to troubleshoot and learn about our products. For additional information about your VorTech Propeller Pump! community.ecotechmarine.com. Propeller Pump, please visit us at UNITED STATES &... -
Page 3: Inside The Box
Inside the Box Maintenance Your VorTech Propeller Pump is designed to operate optimally with little attention after initial setup; however, due to the harsh conditions of a saltwater aquarium and resulting buildup of algae POWER SUPPLY POWER CORD FOAM GUARD and other organic matter, it is advisable to clean your wet side to ensure the longevity of your purchase. -
Page 4: Installing The Vortech
Installing the VorTech ™ STEP 1: Choose Pump Location STEP 4: Place Dry Side on Aquarium • • Where the pump output is unobstructed Place the rubber spacer directly on the wall of the • High enough above the sand bed so sand is not disturbed aquarium at the desired location (Figure B). - Page 5 Installing the VorTech ™ Continued STEP 6: Attach Wet Side STEP 7: Align Pump • Place the wet side into the aquarium and allow ALL air • Plug the power supply into the driver. If the pump is not to escape from the propeller housing. already in Constant Speed Mode, press the MODE button until the control dial is green.
-
Page 6: Mounting The Driver
The EcoSmar t Driver Mounting the Driver 1. Mount the driver where it will not get wet using the included velcro strips (Figure A). Wireless Indicator The driver is NOT water proof, and water damage will NOT be covered under warranty. SET Button LED Strip Figure A... -
Page 7: Operational Modes
EcoSmar t Driver Operational Modes Constant EcoSMART* Random* Short Pulse Gyre Speed Reef Crest Speed Set Speed Set EcoSMART* Random* Short Pulse Gyre Lagoon Freq. Set Freq. Set (Hold) – Feed Mode (Hold) – Power Off Saved Saved Wave Wave LED bar will indicate change between modes. -
Page 8: Tidal Swell Mode
Tidal Swell Mode Nutrient Transport Mode Tidal Swell Mode (TSM) creates a harmonic Nutrient Transport Mode (NTM) creates circulation balance reminiscent of the changing flow in a two-phase program. The first phase uses wave conditions found in nature. Over the course of motion to stir up detritus. -
Page 9: Short Pulse Mode
Short Pulse Mode Gyre Mode When first entering Gyre Mode, set the maximum pump When first entering Short Pulse Mode, set the speed with the control dial and press the SET button maximum pump speed with the control dial and to lock it. -
Page 10: Reef Crest Random Mode
Reef Crest Random Mode Lagoonal Random Mode Reef Crest Random Mode simulates a high-energy reef Lagoonal Random Mode simulates a low-energy environment. It is indicated by both a yellow control lagoon environment. It is indicated by a yellow control dial and the first two blue LEDs illuminated. The control dial and the third and fourth LEDs illuminated. -
Page 11: Troubleshooting
Propeller Pump consists of a wet side operating unit that will be fully submerged in the aquarium and a motor and driver that must not be exposed to water at any time. EcoTech Marine’s warranty shall not apply: (i) to any damaged VorTech... -
Page 12: Regulatory Information
RF Module. Use of this module in products not consented by EcoTech Marine is prohibited. This product is for • DO NOT attempt repairs yourself; return the appliance to the manufacturer for service or discard.
Need help?
Do you have a question about the Vortech MP10 and is the answer not in the manual?
Questions and answers