Advertisement
MMI6056, MMI6070H, MMI8070H, MMI6100, MMI8100,
1.0 Installation and Startup Guide
Install Environment
Where Used
The MMI8000 Series is designed for industrial environments. The operating temperature range is 32 to 113 °F (0
to 45 °C). It may not be suitable for using in certain outdoor applications. Please consult the factory for advised
usage in outdoor applications.
NEMA Rating
The MMI8000 Series front bezel is NEMA 4 rated. When installed properly in a NEMA 4 panel, the NEMA 4 rating
of the panel is not compromised. This means that fluids do not enter the panel during wash downs.
Electrical Environment
The MMI8000 Series has been tested to conform to European CE requirements. This means that the circuitry is
designed to resist the effects of electrical noise. This does not guarantee noise immunity in severe cases. Proper
wire routing and grounding insures proper operation.
Mechanical Environment
Avoid installing units in environments where severe mechanical vibration or shocks are present.
2.0 Installation Instructions
2.1 Mounting Instructions
2.1.1 Location Considerations
Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC output
modules, contactors, starters and relays, and any other source of electrical interference are located away from the
back of the unit.
Take particular note as to the position of variable speed drives and switching power supplies. Their input and load
cables should be screened to a central star earth point.
MMI8000 Series
MMI8104H Installation Instructions
1
Advertisement
Table of Contents
Related Manuals for KEP MMI8000 Series
Summary of Contents for KEP MMI8000 Series
- Page 1 NEMA Rating The MMI8000 Series front bezel is NEMA 4 rated. When installed properly in a NEMA 4 panel, the NEMA 4 rating of the panel is not compromised. This means that fluids do not enter the panel during wash downs.
-
Page 2: Power Connections
Note: Specifications To seal to NEMA-4 specifications, all supplied mounting clamps must be used and panel cannot flex more than 0.010”. 2.1.3 Environmental Considerations The MMI8000 Series units are designed for indoors use as built in displays. Make sure that the displays are installed correctly and that the operating limits are followed (See Specifications). ... -
Page 3: Hardware Considerations
Caution Supply Voltage Note: The 24 VDC output from some controllers may not have enough current to power the MMI8000. Wire lengths should be minimized (Maximum 1600’ (500 m) shielded, 1000’ (300 m) unshielded). Caution Wire Wires should be run in pairs with a neutral or common paired with a hot or Routing signal line. - Page 4 built into the program, with an out-of-limit safe shut down procedure to ensure safety of personnel.
-
Page 5: Communications Connections
ICS 3-304.81 Safety Recommendations: Consideration should be given to the use of an emergency stop function, which is independent of the programmable controller. Where the operator is exposed to the machinery, such as in loading or unloading a machine tool, or where the machine cycles automatically, consideration should be given to the use of an electromechanical override or other redundant means, independent of the programmable controller, for starting and interrupting the cycle. - Page 6 2.3.2 Connector COM1[RS485] , COM3[RS485] and COM3[RS232] The 9 Pin, Female, SUB-D, COM1 [RS-485] , COM3 [RS-485] and COM3 [RS-232] Port on the back of the unit is the RS-232 and RS485/422 communications port for connecting to a controller. Pin assignment of the 9 Pin, Female, SUB-D COM1 [RS-485], COM3 [RS-485] and COM3 [RS- 232] Port Pin# Symbol...
-
Page 7: Adapter Cables
Adapter Cables MT8-COM1/RZC002320 Pin Out 2==> 3==> 4========> 5==> 5==> 5 6========> 7==> 8==> MT8-COM3/RZC004850 Pin Out 1==> 2==> 3==> 4==> 5==> 5==> 5==> 5 6========> 7==============> 8==============> 9========> 2.3. Dip Switch Settings Mode Application mode (On line operations, use ProjectManager or EasyBuilder8000 to change modes) Force to Touch Adjust mode (Used for touchscreen calibration) - Page 8 MMI8000 products are CE-marked to indicate compliance with the EMC Directive. The MMI8000 Series has been designed to operate satisfactorily in electromagnetic noise (immunity) and without emitting high levels of electrical noise into the environment (emission). The units are designed to meet European Community standards when installed per the wiring instructions in this manual.
-
Page 9: Specifications
(1.87 lbs) (1.87 lbs) We hope you will be pleased with our products. If you have any questions concerning our warranty, repair, modification or returned goods process, please contact your local KEP distributor or the KEP Customer Service Department. Warranty This product is warrantied against defects in materials and workmanship for a period of two (2) years from the date of shipment to buyer. - Page 10 Dimensions Drawings are not to scale and are for visual purposes only. Dimensions are in mm (inches) MMI8100/8104...
- Page 11 MMI6056/8056 & MMI6070H/8070H Kessler Ellis Products 10 Industrial Way East Eatontown, NJ 07724 Phone: 732-935-1320 Fax: 732-935-9344 www.kep.com 9900132REV15OCT13...
Need help?
Do you have a question about the MMI8000 Series and is the answer not in the manual?
Questions and answers