Advertisement
Quick Links
INTRODUCTION
The Shed Alarm Kit is an intruder alarm and chime integrated system, designed to protect
your shed. It is a simple to use, easy to install unit.
Whats included in the pack :
1 x Shed Alarm
1 x Door/Window Contact Detector fitted with 5m cable
Fixing Kit (cable clips, screws and wall plugs)
IMPORTANT - Please read this manual carefully, in full, before commencing installation. You
will find installation easier if you follow these steps in the sequence shown.
SAFETY
Before proceeding with the installation, please note the following safety warnings:
DO NOT connect the mains supply directly to the products, this will cause permanent damage
to the products.
Control panel and Door/Window contact are for indoor use only. Avoid mounting location which can
expose the product to splashing or dripping liquid.
Always follow the manufacturer's advice when using power tools and wear suitable protective
equipment (e.g. safety goggles) when drilling holes, etc. Before drilling holes in walls, check for
hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.
Batteries should not be exposed to excessive heat such as sunshine, fire or the like; danger of
damage if battery is incorrectly replaced. Replace only with the same or equivalent type. (Do not
mix batteries type).
1.
-------------P. 2-3
2.
Working modes --------- P. 4-5
3.
Panic alarm -------------P.6
4.
Change password -------P.6
5.
Alarm Hold -------------P.6
6.
-------------P.7
Shed Alarm Kit
User Manual
What you need to purchase :
1 x 9V PP3 Alkaline Battery
1
Advertisement
Related Manuals for Jaycar LA5214
Summary of Contents for Jaycar LA5214
-
Page 1: Table Of Contents
Shed Alarm Kit User Manual INTRODUCTION The Shed Alarm Kit is an intruder alarm and chime integrated system, designed to protect your shed. It is a simple to use, easy to install unit. Whats included in the pack : What you need to purchase : 1 x Shed Alarm 1 x 9V PP3 Alkaline Battery 1 x Door/Window Contact Detector fitted with 5m cable... -
Page 2: Installation
Installation 1.1) Mounting of back-plate a. Mark holes on the wall near the door with the back-plate. b. Then use the screws provided to hang on the back-plate. Mounting Holes 1.2) Installation of Main Unit a. Make sure the Slide Switch is on OFF position. b. - Page 3 1.3) Fix the Main Unit top case / PCB with the two screws at the base. 1.4) Installation of Door Contact Magnetic Switch. Fix the magnet on the door, align it with. the contact switch so that they are no more than 8 mm apart.
-
Page 4: Working Modes
Working Modes DOOR CHIME O U T O U T O U T O U T H O M E H O M E H O M E H O M E O F F O F F O F F O F F INSTANT ALARM H O M E... - Page 5 How to operat Use the slide switch to select HOME, OFF, and OUT mode. At HOME mode, the alarm will sound immediately when the door is opened. At OUT mode, when the door is opened, there is a 20 seconds delay before the alarm sounds. The user may enter the PIN within the delay time to avoid the alarm being activated.
-
Page 6: Panic Alarm
Panic Alarm Press Buttons “7” and “9” together, alarm will sound immediately. (In case of emergency) + + + + 7 7 7 7 9 9 9 9 Change PIN Number User is highly recommended to change the PIN number when using it for the first time. Push the slide switch to “OFF”... -
Page 7: Indications
Indications: ·Alarm hold indication – Red led blinks once every second. ·Low battery indication – Red led blinks once every 4 seconds. ·Mode change – Red led blinks once ·Normal condition – No led on ·Negative response – One long beep Note: 1.