Ryobi RBC36B26E Original Instructions Manual page 3

Safety, performance, and dependability have been given
top priority in the design of your cordless brushcutter and
line trimmer.
INTENDED USE
The line trimmer / brushcutter is intended to be used only by
adults who have read and understood the instructions and
warnings in this manual and can be considered responsible
for their actions. The product is only intended for use
outdoors in a well ventilated area. For safety reasons,
the product must be adequately controlled by using two-
handed operation.
The product fi tted with the line trimmer head (and
appropriate guard) is intended for cutting long grass, pulpy
weed, and similar vegetation at or about ground level.
When fi tted with the Tri-Arc™ blade (and appropriate
guard), it can also cut bushes.
The cutting plane should be approximately parallel to the
ground surface. The product should not be used to cut or
trim hedges, bushes, or other vegetation where the cutting
plane is not parallel to the ground surface.
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
WARNING
The product is not intended to be used by children or
persons with reduced physical, mental or sensory
capabilities. Children should be supervised to ensure
that they do not play with the appliance.
TRAINING
Never allow children or people unfamiliar with the
■
instructions to use the product.
Read the instructions carefully. Be familiar with all
■
controls and the proper use of the product.
Keep the area clear of all bystanders, children and pets
■
while trimming. Stop the product if anyone enters the
area.
Never operate the product when you are tired, ill or
■
under the influence of alcohol, drugs, or medicine.
Use the product for cutting grass and light weeds only.
■
Do not use for any other purpose.
Keep in mind that the operator or user is responsible
■
for accidents or hazards occurring to other people or
their property.
PREPARATION
Wear full eye and hearing protection while operating the
■
product. If working in an area where there is a risk of
falling objects, head protection must be worn.
Hearing protection may restrict the operator's ability to
■
hear warning sounds
Pay particular attention to potential hazards around and
■
inside the work area.
Wear heavy long trousers, boots, and gloves. Do not
■
wear loose fitting clothing, short trousers, jewellery of
any kind, or use with bare feet.
Secure long hair so it is above shoulder level to prevent
■
entanglement in moving parts.
Before use and after any impact, check that there are
■
no damaged parts. A defective switch or any part that
is damaged or worn should be properly repaired or
replaced by an authorised service facility.
Make sure the cutting attachment is properly installed
■
and securely fastened.
Never operate the product unless all guards, deflectors
■
and handles are properly and securely attached.
Consider the environment in which you are working.
■
Keep the working area free from wires, sticks, stones
and debris, which if struck by the cutter, can become
thrown objects.
GENERAL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
■
areas invite accidents.
■ Do not operate power
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
■ Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
■ Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
■ Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
tools in explosive
1