Subscribe to Our Youtube Channel
Related Manuals for Moxa Technologies WAPN005L
Summary of Contents for Moxa Technologies WAPN005L
- Page 1 Moxa IEEE 802.11a/b/g/n Wireless Module WAPN005 User’s Manual First Edition, April 2014 www.moxa.com/product ...
- Page 2 Moxa IEEE 802.11a/b/g/n Wireless Module WAPN005 User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice © 2014 Moxa Inc. All rights reserved. Trademarks The MOXA logo is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited ...
-
Page 3: Table Of Contents
Table of Contents Introduction............................ Overview ............................ Features ............................ Specifications ............................. Getting Started.......................... Module Layout............................ Hardware Block Diagram ........................ Connector Location .......................... Board-to-board Bus Connector PIN Assignments.................. Hardware Installation .......................... Software Installation ........................... -
Page 4: Introduction
Introduction This chapter briefly introduces the overview, features and the specifications of the WAPN005 wireless module. The following topics are covered in this chapter: Overview Features Specifications... -
Page 5: Overview
WAPN005 User's Manual Introduction Overview Moxa WAPN005 module is designed to provide wireless communication for all wireless device based systems. It communicates via the standard 802.11a/b/g/n protocols, and uses the AR9344 wireless chipset from Atheros. Features Dynamic frequency selection (DFS) in required 5-GHz bands All-CMOS MIMO solution interoperable with IEEE 802.11a/b/g/n WLANs No external VCOs or SAW filters needed 2.4/5 GHz WLAN MAC/BB processing BPSK, QPSK, 16 QAM, 64 QAM, DBPSK,DQPSK, and CCK modulation schemes ... - Page 6 WAPN005 User's Manual Introduction ...
-
Page 7: Getting Started
Getting Started This chapter describes the hardware introduction, installation, and software installation. The following topics are covered in this chapter: Module Layout Hardware Block Diagram Connector Location Board-to-board Bus Connector PIN Assignments Hardware Installation Software Installation... -
Page 8: Module Layout
WAPN005 User's Manual Getting Started Module Layout Refer to the following figure for the module layout of the WAPN005. ... -
Page 9: Hardware Block Diagram
WAPN005 User's Manual Getting Started Hardware Block Diagram Refer to the following figure the hardware block diagram of the WAPN005. Connector Location Refer to the following figures for the connector location of the WAPN005 module. Front Rear ... -
Page 10: Board-To-Board Bus Connector Pin Assignments
WAPN005 User's Manual Getting Started Board-to-board Bus Connector PIN Assignments Refer to the following figures and table for the PIN assignment of the WAPN005 module connector. Function Connect to Function Connect to ... -
Page 11: Hardware Installation
WAPN005 User's Manual Getting Started GPIO 2 UR_DTR EMDC GIGA PHY EMDIO GIGA PHY GPIO 11 Reset ... -
Page 12: Regulatory Statement Approval
Regulatory Statement Approval Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - Page 13 WAPN005 User's Manual Regulatory Statement Approval RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN005 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. ...
Need help?
Do you have a question about the WAPN005L and is the answer not in the manual?
Questions and answers