Table of Contents
Advertisement
Quick Links
CVT 1stereo 1ub/2ub/3ub/uhf - II
Installation Instructions
The Channel Vision Multi-Room Video Modulator
makes it easy to map any three audio/video sources
to any unused channels on your television set(s).
Watching your security cameras, laser disk, video
tape, or any other video signal becomes as easy as
switching channels with your remote.
Because the CVT Modulator merges these
additional inputs into your existing TV signal
"ahead of" your television sets the new channels will
be available at every TV hooked up to your coax
cable.
© 2001, Channel Vision
234 F
A
ISCHER
VENUE
(714) 424-6500
(800) 840-0288
l
http://www.channelvision.com
You can even map your stereo system to an unused
TV channel to pipe music to any room on your TV
"network"!
Please note: Some TV tuners need a video input to
achieve audio output.
C
M
, CA 92626
OSTA
ESA
l
(714) 424-6510
l
E-Mail: sales@channelvision.com
l
FAX
Advertisement
Table of Contents
Summary of Contents for Channel Vision Stereo Receiver
-
Page 1: Installation Instructions
CVT 1stereo 1ub/2ub/3ub/uhf - II Installation Instructions The Channel Vision Multi-Room Video Modulator makes it easy to map any three audio/video sources to any unused channels on your television set(s). Watching your security cameras, laser disk, video tape, or any other video signal becomes as easy as switching channels with your remote. -
Page 2: Basic Installation Instructions
Consult the dealer or an experienced radio/TV technician for help. Basic Installation Instructions The Channel Vision Multi-Room Video CVT Modulator is easy to hook-up. Just connect your video sources to the CVT Modulator as you would connect them directly to your TV's "video in."... -
Page 3: System Design Considerations
CVT 3ub/uhf Basic Setup Source A/V Inputs Cable or Antenna CVT 3UB/UHF Channel Vision MULTI ROOM VIDEO TECHNOLOGY CVT - 15PIA HS-2 HS-3 Setting Up TV Channel Range Example of Dip Switch Settings Switch Band/Channels Cable (59-86 see note Cable (65-135) Antenna (14-78) Antenna (14-39) &... -
Page 4: System Installation Checklist
Adjustments Attenuator: Decrease signal strength (output dBmV) of modulator. Stereo Loop: Used to pass stereo to TV on non-stereo modulator. position is normal, 1K position if using stereo loop. Video Level Adjustment: Adjust the incoming video source base band level. Use only to increase brightness and balance the channels for consistent contrast. - Page 5 TV Won't Tune High Enough to get Modulated Channel Use an external tuner i.e. VCR or a Cable Box converter tuner (Channel Vision Model #1172) to allow the TV to view a modulated channel on channel through the external tuner.
- Page 6 9dB, 12dB, to close TVs. 16dB, 20dB). 150' 12dB Hookup with stereo receiver, Stereo VCR and Cable Box Converter and use your stereo receiver for A/V Out A/V In Five channels total, four for individual camera channel and one Cable or...
- Page 7 70 and 80 and above, allowing two channels to modulate. Channel Vision also has low/high pass in a single filter part # 3205-60/69. This filter has a 4 channel slope on both sides allowing 2 channels to modulate 64-66. The 3205-70/79 filter also allows two channels 74-76.
- Page 8 DIAGRAM#A/OPTION 2 2-RG-6 COAX TO EACH LOCATION-DEDICATING THE DIGITAL CONVERTER BOXES. DEDICATING CATV MODULATION/ RECOMBINING AT TV HS-2 DIGITAL Cable Box HS-8 DIGITAL Cable Box A/V SOURCES CVT 1UB/UHF-II CH 85 COMBINER KIT CAN BE USED IF NO VIDEO A/V-OUT TO TV 3102-118 LOW PASS DIAGRAM#C FILTER USED WITH...
- Page 9 Channel Vision Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occur during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase.
Need help?
Do you have a question about the Stereo Receiver and is the answer not in the manual?
Questions and answers