Table of Contents
Advertisement
OWNER'S MANUAL
DVD Home Theater
System
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE WARRANTY TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
HT806PH (HT806PH, SH86TH-S/ C, SH86SH-S, SH95TA-W)
P/NO : MFL67084756
HT806PH-D0_BGBRLL_ENG_4756.indd 1
2011-02-15
10:10:49
Advertisement
Table of Contents
Related Manuals for LG HT806PH
Summary of Contents for LG HT806PH
- Page 1 Please read this manual carefully before operating your set and retain it for future reference. FOR THE WARRANTY TERMS & CONDITIONS, PLEASE REFER TO BACK COVER OF THIS MANUAL. HT806PH (HT806PH, SH86TH-S/ C, SH86SH-S, SH95TA-W) P/NO : MFL67084756 HT806PH-D0_BGBRLL_ENG_4756.indd 1 2011-02-15...
- Page 2 WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future HT806PH-D0_BGBRLL_ENG_4756.indd 2 reference. Shall the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
- Page 3 2. A ll electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. T he correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. HT806PH-D0_BGBRLL_ENG_4756.indd 3 Getting Started 4. F or more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/EC. European representative : LG Electronics Service Europe B.V.
-
Page 4: Table Of Contents
– USB Connection – OPTICAL In connection – Home theater speaker ez setup Antenna Connection HT806PH-D0_BGBRLL_ENG_4756.indd 4 System Setting Adjust the setup settings – OSD Initial language settings - Optional – To display and exit the Setup menu –... - Page 5 Troubleshooting Troubleshooting Appendix Maintenance – Handling the Unit – Notes on Discs Area Code List Language code List Trademarks and Licenses Specifications Warranty Warranty HT806PH-D0_BGBRLL_ENG_4756.indd 5 Table of Contents 2011-02-15 10:10:49...
-
Page 6: Getting Started
Getting Started Unique Features Portable In Listen to music from your portable device. (MP3, Notebook, etc) USB Direct Recording Records music from CD to your USB device. Full HD up-scaling Views Full HD picture quality with simple setup. Home Theater Speaker ez Setup Listen to sounds from TV, DVD and Digital device with vivid 5.1 (2.1 or 2.0) ch mode. HT806PH-D0_BGBRLL_ENG_4756.indd 6 Accessories Please check and identify the supplied accessories. Remote control (1) Battery (1) FM antenna (1) Speaker cables (4) 2011-02-15 10:10:50... -
Page 7: Introduction
DVD-RW (8 cm / 12 cm disc) Video mode and finalized only. DVD+R: Video mode only Supports the double layer disc also. DVD+RW (8 cm / 12 cm disc) Video mode and finalized only. Audio CD: Music CDs or CD-R/CD- RW in music CD format that can be purchased. About the “&” Symbol Display “&” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media. HT806PH-D0_BGBRLL_ENG_4756.indd 7 Getting Started Symbols Used in this Manual DVD-Video, DVD±R/RW in Video mode or VR mode and finalized Audio CDs Video files contained in the USB/Disc Audio files contained in the USB/Disc Photo files Note Indicates special notes and operating features. Indicates tip and hints for making the task easier. > Caution Indicates cautions for preventing possible damages from abuse. -
Page 8: Playable File Requirement
CD-ROM file format : ISO9660/ JOLIET y We recommend that you use Easy-CD Creator, which creates an ISO9660 file system. Photo file requirement Photo file compatibility with this unit is limited as follows : y Max pixel in width : 2 760 x 2 048 pixel y Maximum files : Under 999 y Some discs may not operate due to a different recording format or the condition of disc. y File extensions: “.jpg” y CD-ROM file format : ISO9660/ JOLIET HT806PH-D0_BGBRLL_ENG_4756.indd 8 DivX file requirement DivX file compatibility with this unit is limited as follows: y Available resolution: within 720 x 576 (W x H) pixels. y The file name of the DivX subtitle should be entered within 45 characters. y If there is impossible code to express in the DivX file, it may be displayed as “ _ “ mark on the display. y Frame rate : less than 30 fps. -
Page 9: Remote Control
• • • • • • a • • • • • P RADIO&INPUT: Changes input sources. MARKER: Marks play list. 1 POWER: Switches the unit ON or OFF. B OPEN/CLOSE: Opens and closes the disc Drawer. HT806PH-D0_BGBRLL_ENG_4756.indd 9 SLEEP: Sets the System to turn off • • • • • • d • • • • • automatically at a specified time. SPEAKER LEVEL: Sets the sound (Dimmer : The display window will level of desired speaker. be darken by half.) -
Page 10: Front Panel
T (PLAY/PAUSE) Starts playback. Pauses playback temporarily, press again to exit pause mode. d I STOP Stops playback. e Y/U (SKIP) Goes to next or previous file/track/chapter. Searches backward or forward (Press and hold) Tunes in the desired radio station. f FUNC. (FUNCTION) Changes the input source or function. HT806PH-D0_BGBRLL_ENG_4756.indd 10 b c d e f g VOLUME Adjusts speaker volume. h Display window Shows the current status of the unit. i Disc Tray j USB Port Connects a USB device. k PORT. IN Connects to a portable player with audio outputs. -
Page 11: Rear Panel
Rear panel a Power cord b Speakers connectors Connects the speaker cables. c Cooling Fan d Antenna Connector FM- Connects the FM wired antenna e SCART connetcor f VIDEO OUT Connects to a TV with video inputs. HT806PH-D0_BGBRLL_ENG_4756.indd 11 g HDMI OUT Connects to TV with HDMI inputs. (Interface for digital audio and video) h OPTICAL IN Connects to optical audio equipment. i COMPONENT VIDEO (Y P (PROGRESSIVE SCAN) Connects to a TV with Y P j AUX (L/R) INPUT Connects to an external source with 2 channel audio outputs. Getting Started j i h )OUTPUT inputs. -
Page 12: Connecting
Connecting Assembling the speaker stand to the speaker Before connecting the speakers, assemble the speakers. Please check the items for assembling the speakers. Preparation Speaker Stand HT806PH-D0_BGBRLL_ENG_4756.indd 12 Attach the speakers to the speaker stands by rotating the screws. 2011-02-15 10:10:51... -
Page 13: Attaching The Speakers To The Unit
Attaching the speakers to the unit 1. Connect the wires to the unit. Match each wire’s colored band to the same colored connection terminal on the rear of the unit. To connect the cable to the unit, press each plastic finger pad to open the connection terminal. Insert the wire and release the finger pad. Connect the black stripe of each wire to the terminals marked -(minus) and the other end to the terminals marked + (plus). 2. Connect the wires to the speakers. Connect the other end of each wire to the correct speaker according to the color coding: HT806PH-D0_BGBRLL_ENG_4756.indd 13 Connecting Color Speaker Position Grey Rear Rear right Blue Rear Rear left Green Center Center Orange Sub woofer Any front position Front... -
Page 14: Positioning The System
Connecting Positioning the system The following illustration shows an example of positioning the system. Note that the illustrations in these instructions differ from the actual unit for explanation purposes. For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position ( ). HT806PH-D0_BGBRLL_ENG_4756.indd 14 F ront left speaker (L)/ Front right speaker (R): Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible. C enter speaker: Place the center speaker above or below the monitor or screen. S urround left speaker (L)/ Surround right speaker (R): Place these speakers behind your listening position, facing slightly inwards. S ubwoofer: The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections. Unit 2011-02-15 10:10:52... -
Page 15: Connections To Your Tv
Make one of the following connections, depending on the capabilities of your existing equipment. Note y Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described in this manual. y Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. > Caution y Make sure the unit is connected directly to the TV. Tune the TV to the correct video input channel. y Do not connect your player via your VCR. The image could be distorted by the copy protection system. HT806PH-D0_BGBRLL_ENG_4756.indd 15 Connecting Component Video Connection Connect the COMPONENT VIDEO OUTPUT (PROGRESSIVE SCAN) jacks on the unit to the corresponding input jacks on the TV using component cables. You can hear the sound through the system’s speakers. Green Blue Unit 2011-02-15 10:10:52... -
Page 16: Hdmi Out Connection
HDMI Out Connection If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable (Type A, High Speed HDMI™ Cable). Connect the HDMI OUT jack on the unit to the HDMI IN jack on a HDMI compatible TV or monitor. Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Unit y You can fully enjoy digital audio and video signals together with this HDMI connection. y When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 18.) HT806PH-D0_BGBRLL_ENG_4756.indd 16 Note y If a connected HDMI device does not accept the audio output of the unit, the HDMI device’s audio sound may be distorted or may not output. y When you connect a HDMI or DVI compatible device make sure of the following: - T ry switching off the HDMI/DVI device and this unit. Next, switch on the HDMI/ DVI device and leave it for around 30 seconds, then switch on this unit. - T he connected device’s video input is set correctly for this unit. -
Page 17: Video Connection
Video Connection Connect the VIDEO OUT jack on the unit to the video in jack on the TV using a video cable. You can hear the sound through the system’s speakers. HT806PH-D0_BGBRLL_ENG_4756.indd 17 SCART Connection Connect the SCART jack on the unit to the SCART in jack on the TV using a SCART cable. You can hear the sound through the system’s speakers. Unit Yellow Connecting Unit 2011-02-15 10:10:54... -
Page 18: Resolution Setting
Connecting Resolution Setting The unit provides several output resolutions for HDMI OUT and COMPONENT VIDEO OUT jacks. You can change the resolution using [Setup] menu. 1. Press n HOME. 2. Use A/D to select the [Setup] and press b ENTER. The [Setup] menu appears. 3. Use W/S to select [Display] option then press D to move to the second level. 4. Use W/S to select the [Resolution] option then press D to move to the third level. 5. Use W/S to select the desired resolution then press b ENTER to confirm your selection. Note If your TV does not accept the resolution you have set on the player, you can set resolution to 480p (or 576p) as follows: Press Z STOP for more than 5 seconds. HT806PH-D0_BGBRLL_ENG_4756.indd 18 Video Output Resolution Displayed resolution in display window and outputted resolution may different according to connection type. [HDMI OUT]: 1 080p, 1 080i, 720p and 480p (or 576p) and 480i (or 576i) [COMPONENT VIDEO OUT]: 480p (or 576p) and 480i (or 576i) [VIDEO OUT]: 480i (or 576i) 2011-02-15 10:10:54... -
Page 19: Optional Equipment Connection
AUX In Connection Connect an Output of auxiliary device to the AUX (L/R) INPUT Connector. To the audio output jacks of your component (TV, VCR, etc.) Note If your TV has only one output for audio (mono), connect it to the left (white) audio jack on the unit. HT806PH-D0_BGBRLL_ENG_4756.indd 19 AUDIO (PORT. IN) In Connection Connect an output of portable device (MP3 or PMP etc) to the AUDIO (PORT. IN) input connector. Unit Listening to music from your portable player or external device The unit can be used to play the music from many types of portable player or external devices. -
Page 20: Usb Connection
Connecting USB Connection Connect the USB port of USB Memory (or MP3 player, etc.) to the USB port on the front of the unit. Removing the USB Device from the unit 1. Choose a different function mode or press Z STOP twice in a row. 2. Remove the USB device from the unit. HT806PH-D0_BGBRLL_ENG_4756.indd 20 Compatible USB Devices y MP3 Player : Flash type MP3 player. y USB Flash Drive : D evices that support USB2.0 or USB1.1. y The USB function of this unit does not support some USB devices. USB device requirement y Devices which require additional program installation connected to a computer, are not supported. y Do not extract the USB device while in operation. y For a large capacity USB, it may take longer than a few minute to be searched. y To prevent data loss, back up all data. -
Page 21: Optical In Connection
Home theater speaker ez setup Listen to sound from TV, DVD and Digital Device with 5.1(2.1 or 2)ch mode. Even in power off mode, if you press OPTICAL, then power is on and automatically changed to AUX OPT mode. 1. Connect the unit’s OPTICAL IN jack to jack on optical out of your TV (or Digital Device etc.). 2. Select the AUX OPT by using the OPTICAL. To select the AUX OPT directly. 3. Listen sound with 5.1(2.1 or 2)ch speaker. 4. To escape from AUX OPT by using the OPTICAL. Function is retuned to previous one. HT806PH-D0_BGBRLL_ENG_4756.indd 21 Connecting Antenna Connection Connect the supplied FM antenna for listening to the radio. Connect the FM Wire antenna to the FM antenna connector. Note Be sure to fully extend the FM wire antenna. After connecting the FM wire antenna, keep it as horizontal as possible. 2011-02-15 10:10:55... -
Page 22: System Setting
1. Press 1 (POWER) to turn the unit on. The language setup menu will appear on the screen. 2. Use WSAD to select a language then press b ENTER. The confirm menu will appear. 3. Use AD to select the [Enter] then press b ENTER to finish the language setup. HT806PH-D0_BGBRLL_ENG_4756.indd 22 To display and exit the Setup menu 1. Press n HOME. Displays the [Home Menu]. 2. Select an [Setup] by using AD. 3. Press b ENTER. Displays the [Setup]. 4. Press n HOME or x RETURN to exit in the [Setup] Menu. About help menu for Setup Menu... -
Page 23: Language
[Off (for Disc Subtitle)] Turn off Subtitle. Display TV Aspect Select which screen aspect to use based on the shape of your TV screen. [4:3] Select when a standard 4:3 TV is connected. [16:9] Select when a 16:9 wide TV is connected. Display Mode The Display Mode setting works only when the TV Aspect mode is set to 4:3. [Letterbox] Displays a wide picture with bands on the upper and lower portions of the screen. HT806PH-D0_BGBRLL_ENG_4756.indd 23 System Setting [Panscan] Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (If the disc/file is not compatible with Pan Scan, the picture is displayed at Letterbox ratio.) TV Output Select Select an option according to the TV connection type. [RGB] When your TV is connected with the SCART jack. When your TV is connected with the COMPONENT/ PROGRESSIVE SCAN jacks on the unit. -
Page 24: Audio
System Setting Audio 5.1 Speaker Setup Make the following settings for the built-in 5.1 channel surround decoder. 1. Select [5.1 Speaker Setup] on the [Audio] menu. 2. Press b ENTER. The [5.1 SPEAKER] appears. 3. Use AD to select the desired speaker. 4. Adjust options using WSAD buttons. 5. Returns to the previous menu by pressing x RETURN. HT806PH-D0_BGBRLL_ENG_4756.indd 24 [Speaker] Select a speaker that you want to adjust. Note Certain speaker settings are prohibited by the Dolby Digital licensing agreement. [Size] Since the speaker settings are fixed, you cannot change the settings. [Volume] Press AD to adjust the output level of the selected speaker. Front L/R : 0 ~ -5 SubWoofer, Rear L/R, Center : 5 ~ -5 [Distance] After you connected speakers to your unit, set the Distance between the speakers and your listening point if the distance of Center or Rear speakers is bigger than the distance of Front speakers. This allows the sound from... -
Page 25: Lock (Parental Control)
Select [On] to mix karaoke channels into normal stereo. This function is effective for multi-channel karaoke DVDs only. HD AV Sync Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use WS (on the remote control) to scroll up and down through the delay amount, which you can set at anything between 0 and 300m sec. HT806PH-D0_BGBRLL_ENG_4756.indd 25 System Setting Lock (Parental Control) Initial Setting the Area Code: When you use this unit for the first time, you have to set the Area Code. 1. Select the [Lock] menu and then press D. 2. Press D. To access the [Lock] options, you must input the password you have created. Input a password and press b ENTER. Enter it again and press b ENTER to verify. If you make a mistake before pressing b ENTER, press CLEAR. -
Page 26: Others
Menu]. 2. Input the 6-digit number “210499” and press b ENTER. The password is cleared. Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 38. 1. Select [Area Code] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select the first character using WS buttons. 4. Press b ENTER and select the second character using WS buttons. 5. Press b ENTER to confirm your Area code selection. HT806PH-D0_BGBRLL_ENG_4756.indd 26 Others DivX VOD We provide you with the DivX® VOD (Video On Demand) registration code that allows you to rent and purchase videos using the DivX® VOD service. For more information, visit www.divx.com/vod. [Register] Displays the registration code of your player. [Deregister] Deactivate your player and display the deactivation code. Note All the downloaded videos from DivX VOD can only be played back on this unit. 2011-02-15... -
Page 27: Operating
Using the Home Menu 1. Press n HOME. Displays the [Home Menu]. 2. Select an option by using AD. 3. Press b ENTER then selected option menu. [Music] – Displays [MUSIC] menu. [Movie] – S tart video media’s playback or displays the [MOVIE] menu. [Photo] – Displays [PHOTO] menu. [Setup] – Displays the [Setup] menu. Note You can not select the [Music], [Movie] or [Photo] option when the USB device is not connected or a disc is not inserted. HT806PH-D0_BGBRLL_ENG_4756.indd 27 Operating Basic Operations 1. Insert the disc by using the B OPEN/CLOSE or Connect the USB device to the USB port. 2. Press n HOME. Displays the [Home Menu]. 3. Select an option by using AD. If you select the [Movie], [Photo] or [Music] option when you connect up to two devices, it appears as belows. Select a media then press b ENTER. 4. Press b ENTER then selected option menu. Note y For the most Audio CD and DVD-ROM discs, playback starts automatically. -
Page 28: Other Operations
- DVD : Chapter/ Title/ Off randomly - DivX : Title/ All/ Off - A udio CD/ MP3/ WMA : Track/ All/ Random/ Off In the pause mode, press Slowing down SLOW (c or v) to select the playing the required speed. (DVD, DivX speed only) The DivX file cannot be slow down reverse playback. HT806PH-D0_BGBRLL_ENG_4756.indd 28 Other Operations Do this Displaying Disc Information on-screen You can display various information about the disc loaded on-screen. 1. Press m INFO/DISPLAY to show various playback information. The displayed items differ depending on the disc type or playing status. 2. You can select an item by pressing WS,and change or select the setting by pressing AD. Title – C urrent title number/ total number of titles. Chapter – C urrent chapter number/ total number of chapters. -
Page 29: To Display The Dvd Menu
3. Press d PLAY, MONO/STEREO to confirm. 1.5 times speed playback The 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed. 1. During playback, press d PLAY, MONO/ STEREO to play at 1.5 times speed. “dX1.5” appears on the screen. 2. Press d PLAY, MONO/STEREO again to exit. Screen Saver The screen saver appears when you leave the unit in Stop mode for about five minutes. HT806PH-D0_BGBRLL_ENG_4756.indd 29 Operating Starting play from selected time To start playing at any chosen time on the file or title. 1. Press m INFO/DISPLAY during playback. 2. Press WS to select the time clock icon and “--:--:--” appears. 3. Input the required start time in hours, minutes, and seconds from left to right. If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then input the correct... -
Page 30: Marked Playback
PLAY, MONO/STEREO. 3. Press ENTER or Displays the play mode. 4. Select the play mode by using the ENTER. [Mark Play] Marked playback. [Current Play] Normal playback. Note If you want to select all files on the list, select [Select All] and press b ENTER. HT806PH-D0_BGBRLL_ENG_4756.indd 30 To delete a Marker 1. Use to select the track that you wish to erase from the marked file. 2. Press MARKER. To delete all Markers Use WSAD to select [Deselect All] then press b ENTER in program edit mode. Note The markers are also cleared when the disc or USB device is removed, the unit is switched to power off or the function is switched to others. -
Page 31: Viewing A Photo File
Moving to another WSAD Move file or content. Viewing a particular b ENTER Select file. Returning to the x RETURN Close [Home Menu]. HT806PH-D0_BGBRLL_ENG_4756.indd 31 About help menu in the full screen Menu Buttons Menu DISPLAY Prev./ Next next file list. RETURN Close Options while viewing a photo You can use various options during viewing a photo in full screen. 1. While viewing a photo in full screen, press m INFO/DISPLAY to display the option menu. -
Page 32: Sleep Timer Setting
Last Scene Memory This unit memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. System Select - Optional You must select the appropriate system mode for your TV system. Press and hold M PAUSE/STEP for more than five seconds to be able to select a system in the [Home Menu]. Note If the USB device is connected or a disc is inserted, this function is not operated. HT806PH-D0_BGBRLL_ENG_4756.indd 32 Adjust the speaker level settings You can adjust the sound level of each speaker. 1. Press SPEAKER LEVEL repeatedly to select a desired speaker to set. 2. Press VOL -/+ to adjust the sound level of the selected speaker while the level setting memu is displayed on the display window. 3. Repeat and adjust the sound level of the other speakers. 2011-02-15 10:10:56... -
Page 33: Radio Operations
5. Press b ENTER. The station is stored. 6. Repeat the steps 2 to 5 to store other stations. Deleting all the saved stations 1. Press and hold CLEAR for two seconds. “ERASE ALL” will flash up on the unit display. 2. Press CLEAR to erase all saved of the radio stations. HT806PH-D0_BGBRLL_ENG_4756.indd 33 Operating Deleting a saved station 1. Press PRESET - / + to Select a preset number you want to delete. 2. Press CLEAR, the preset number will blink in the display window. 3. Press CLEAR again, to delete the selectd preset number. Improving poor FM reception Press d PLAY, MONO/STEREO on the remote control. This will change the tuner from stereo to... -
Page 34: Sound Adjustment
JAZZ rock pop, jazz or classic ROCK concert. This function is optimized for MP3 OPT compressible MP3, WMA file. It improves the treble sound. The BASS is Bass Blast. During playback, reinforce the treble, BASS bass and surround sound effect. Improves the bass and treble LOUDNESS sound. HT806PH-D0_BGBRLL_ENG_4756.indd 34 On Display VIRTUAL BYPASS Note y In some of surround modes, some speakers, there’s no sound or low sound. It depends on the mode of surround and the source of audio, it is not defective. y You may need to reset the surround mode, Description after switching the input, sometimes even after the sound track changed. Description The VIRTUAL is VSM Plus. You can enjoy more virtual surround sound. You can enjoy the sound without equalizer effect. -
Page 35: Advanced Operations
[All tracks/ files recording] Record to USB in stop or play mode. [Program list recording] After marking desired file(s) and you can record it to USB (Refer to the page 30). It’ll be stored as follows. Audio CD MP3/ WMA The other sources (Tuner, AUX, Portable) HT806PH-D0_BGBRLL_ENG_4756.indd 35 Operating Note y You can check the recording percentage rate for the USB record on the screen during the recording. (Audio CD or MP3/ WMA CD only) y During recording MP3/WMA, there is no sound. y When you stop recording during playback, the file that has been recorded at that time will be stored. (Audio CD only) -
Page 36: Troubleshooting
Troubleshooting Troubleshooting PROBLEM No power No picture There is little or no sound The DVD picture quality is poor A DVD/CD will not play Humming noise heard while a DVD or CD is playing Radio stations can’t be tuned in properly The remote control doesn’t work well / at all HT806PH-D0_BGBRLL_ENG_4756.indd 36 CORRECTION Plug the power cord into the wall outlet securely. Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen. Connect the video cables securely to both the TV and unit. Select the correct input mode of the unit so you can hear the sound from the unit. Connect the audio cables into the connection terminals correctly. Replace with a new audio cable. Clean the disc using a soft cloth with outward strokes. Insert a disc. Insert a playable disc (check the disc type, colour system and regional code). Place the disc with the label or printed side facing upwards. Enter your password or change the rating level. Clean the disc using a soft cloth with outward strokes. Move unit and audio components further away from your TV. Check the antenna connection and adjust its position. Attach an external aerial if necessary. Tune to the station manually. Preset some radio stations, see page 33 for details. The remote is not pointed directly at the unit. Point the remote directly at the unit. The remote is too far from the unit. -
Page 37: Appendix
Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Maintaining the Unit The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center. HT806PH-D0_BGBRLL_ENG_4756.indd 37 Appendix Notes on Discs Handling Discs Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing,... -
Page 38: Area Code List
Congo Jamaica Costa Rica Japan Croatia Kenya Czech Republic Kuwait Denmark Libya Ecuador Luxembourg Egypt Malaysia El Salvador Maldives Ethiopia Mexico HT806PH-D0_BGBRLL_ENG_4756.indd 38 Code Area Code Area Monaco Singapore Mongolia Slovak Republic Morocco Slovenia Nepal South Africa Netherlands South Korea Antilles Spain New Zealand Sri Lanka Nigeria Sweden... -
Page 39: Language Code List
Kirghiz English 6978 Korean Esperanto 6979 Kurdish Estonian 6984 Laothian Faroese 7079 Latin Fiji 7074 Latvian, Lettish Finnish 7073 Lingala HT806PH-D0_BGBRLL_ENG_4756.indd 39 Code Language Code Language 7082 Lithuanian 7684 Sindhi 7089 Macedonian 7775 Singhalese 7176 Malagasy 7771 Slovak 7565 Malay 7783... -
Page 40: Trademarks And Licenses
“DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation. DivX®, DivX Certified® and associated logos are trademarks of DivX, Inc. and are used under license. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. HT806PH-D0_BGBRLL_ENG_4756.indd 40 What is SIMPLINK? Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc. y Refer to the TV owner’s manual for the details of SIMPLINK function. y LG TV with SIMPLINK function has the logo as shown above. y Use a higher version cable than High Speed HDMI™ Cable. 2011-02-15 10:10:57... -
Page 41: Specifications
Operating humidity Bus Power Supply (USB) Inputs/ Outputs VIDEO OUT COMPONENT VIDEO OUT HDMI OUT (video/audio): ANALOG AUDIO IN DIGITAL IN (OPTICAL): PORT. IN Amplifier Stereo mode 141 W + 141 W (3 Ω at 1kHz) Front Center Surround mode Surround Subwoofer Tuner FM Tuning Range HT806PH-D0_BGBRLL_ENG_4756.indd 41 200 - 240 V, 50/60 Hz 95 W 360 x 62.5 x 312.3 mm without foot 2.8 kg 41 °F to 95 °F (5 °C to 35 °C) 5 % to 90 % DC 5 V 0 500 mA 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 19 pin (Type A, HDMI™ Connector ) 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1 3 V (p-p), Optical jack x 1 0.5Vrms (3.5 mm stereo jack) 141 W + 141 W (3 Ω at 1 kHz) 141 W (3 Ω at 1 kHz) 141 W + 141 W (3 Ω at 1 kHz)) 145 W (3 Ω at 60 Hz) 87.5 to 108.0 MHz or 87.50 to 108.00 MHz... - Page 42 Net Dimensions (W x H x D) Net Weight Centre Speaker Type Impedance Rated Input Power Max. Input Power Net Dimensions (W x H x D) Net Weight Passive Subwoofer Type Impedance Rated Input Power Max. Input Power Net Dimensions (W x H x D) Net Weight Design and specifications are subject to change without notice. HT806PH-D0_BGBRLL_ENG_4756.indd 42 2 Way 2 speaker 3 Ω 141 W 282 W 260 x 1 102 x 200 mm 2.68 kg 1 Way 1 Speaker 3 Ω 141 W 282 W 102 x 193 x 81 mm 0.5 kg 2 Way 2 speaker 3 Ω 141 W 282 W 250 x 100 x 88 mm 0.6 kg 1 Way 1 Speaker 3 Ω...
-
Page 43: Warranty
AT THE TIME GUARANTEE SERVICE IS PROVED. • Product Registration Card : It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should modifications be necessary. • To obtain information or assistance: C all 0870 873 5454 Monday-Friday 9.00am-4.30pm MODEL NO.* In all cases of difficulty - consult your LG dealer from whom the product was purchased LGEUK Website : www.lge.co.uk ( service website : www.lgelectronics.co.uk ) HT806PH-D0_BGBRLL_ENG_4756.indd 43 Technology with the human touch GUARANTEE SERIAL NO.* Warranty DATE OF PURCHASE.*... - Page 44 HT806PH-D0_BGBRLL_ENG_4756.indd 44 2011-02-15 10:10:57...