Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LG HT906SC
Summary of Contents for LG HT906SC
- Page 1 OWNER’S MANUAL DVD Home Cinema System Please read this manual carefully before operating your set and retain it for future reference. HT906SC (HT906SC, SH96SB-S/ C, SH95TA-W) P/NO : MFL67164740 HT906SC-R0_BDEULL_ENG_4740.indd 1 2011-02-19 1:58:06...
- Page 2 Any of these conditions could result in electric accompanying the product. shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK or deterioration, unplug it, discontinue use of the HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN appliance, and have the cord replaced with an OR MOISTURE. exact replacement part by an authorized service WARNING: Do not install this equipment in a center. Protect the power cord from physical or confined space such as a book case or similar unit. mechanical abuse, such as being twisted, kinked, CAUTION: Do not block any ventilation openings. pinched, closed in a door, or walked upon. Pay Install in accordance with the manufacturer’s particular attention to plugs, wall outlets, and instructions. the point where the cord exits the appliance. To Slots and openings in the cabinet are provided for disconnect power from the mains, pull out the ventilation and to ensure reliable operation of the mains cord plug. When installing the product, product and to protect it from over heating. The ensure that the plug is easily accessible. openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built- in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. HT906SC-R0_BDEULL_ENG_4740.indd 2 2011-02-19 1:58:07...
- Page 3 LG Electronics hereby declares that this/ of this copyright protection technology must be these product(s) is/are in compliance authorized by Macrovision, and is intended for with the essential requirements and home and other limited viewing uses only unless other relevant provisions of Directive otherwise authorized by Macrovision. Reverse 2004/108/EC, 2006/95/EC, and engineering or disassembly is prohibited. 2009/125/EC. CONSUMERS SHOULD NOTE THAT NOT ALL European representative : HIGH DEFINITION TELEVISION SETS ARE FULLY LG Electronics Service Europe B.V. COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE Veluwezoom 15, 1327 AE Almere, The ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN Netherlands (Tel : +31–(0)36–547–8888) CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. HT906SC-R0_BDEULL_ENG_4740.indd 3 2011-02-19 1:58:07...
-
Page 4: Table Of Contents
Sound adjustment – USB Connection – Setting the surround mode – OPTICAL In connection Advanced Operations – Home theater speaker ez setup – Recording to USB Antenna Connection Playing the iPod – Preparation HT906SC-R0_BDEULL_ENG_4740.indd 4 2011-02-19 1:58:07... - Page 5 Table of Contents – Enjoying iPod on the screen – Enjoying the iPod IN mode Troubleshooting Troubleshooting Appendix Maintenance – Handling the Unit – Notes on Discs Area Code List Language code List Trademarks and Licenses Specifications HT906SC-R0_BDEULL_ENG_4740.indd 5 2011-02-19 1:58:07...
-
Page 6: Getting Started
Getting Started Unique Features Accessories Please check and identify the supplied accessories. Portable In Listen to music from your portable device. (MP3, Notebook, etc) USB Direct Recording Remote control (1) Battery (1) Records music from CD to your USB device. Full HD up-scaling Views Full HD picture quality with simple setup. Home Theater Speaker ez Setup FM antenna (1) Speaker cables (6) Listen to sounds from TV, DVD and Digital device with vivid 5.1 (2.1 or 2.0) ch mode. Made for iPod Enjoys music from IPod with simple connection. RCA to SCART cable (1) HT906SC-R0_BDEULL_ENG_4740.indd 6 2011-02-19 1:58:07... -
Page 7: Introduction
DVD-RW (8 cm / 12 cm disc) > Caution Video mode and finalized only. DVD+R: Video mode only Indicates cautions for preventing possible damages from abuse. Supports the double layer disc also. DVD+RW (8 cm / 12 cm disc) Regional Codes Video mode and finalized only. This unit has a regional code printed on the rear of Audio CD: Music CDs or CD-R/CD- the unit. This unit can play only DVD discs labeled RW in music CD format that can be same as the rear of the unit or “ALL”. purchased. y Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or About the “&” Symbol the disc cannot play. Display y If you try to play a DVD with a different regional code from your unit, the message “Check “&” may appear on your TV display during Regional Code” appears on the TV screen. operation and indicates that the function explained in this owner’s manual is not available on that specific media. HT906SC-R0_BDEULL_ENG_4740.indd 7 2011-02-19 1:58:08... -
Page 8: Playable File Requirement
Photo file requirement “DIVX5.xx”, “MP4V3”, “3IVX”. Photo file compatibility with this unit is limited as y Playable Audio format : “AC3”, “DTS”, “PCM”, “MP3”, follows : “WMA”. y Max pixel in width : 2 760 x 2 048 pixel y Sampling frequency : within 32 to 48 kHz (MP3), within 32 to 48 kHz (WMA) y Maximum files : Under 999 y Bit rate : within 32 to 320 kbps (MP3), 40 to 192 y Some discs may not operate due to a different kbps (WMA) recording format or the condition of disc. y For Discs formatted in Live file system, you can y File extensions: “.jpg” not it on this unit. y CD-ROM file format : ISO9660/ JOLIET y If the name of movie file is different from that of the subtitle file, during playback of a DivX file, subtitle may not be display. y If you play a DivX file differ from DivXspec, it may not operate normally. HT906SC-R0_BDEULL_ENG_4740.indd 8 2011-02-19 1:58:08... -
Page 9: Remote Control
PLAY, MONO/STEREO: Starts the RDS. rear of the Remote Control, and playback. Selects Mono/ Stereo. insert one (size AAA) battery with M PAUSE/STEP: Pauses playback. 4 and 5 matched correctly. C/V SKIP: Goes to the next • • • • • • a • • • • • or previous chapter / track / file. c/v SCAN: Searches P RADIO&INPUT: Changes input sources. backward or forward. MARKER: Marks play list. 1 POWER: Switches the unit ON or OFF. B OPEN/CLOSE: Opens and closes the disc Drawer. HT906SC-R0_BDEULL_ENG_4740.indd 9 2011-02-19 1:58:08... -
Page 10: Front Panel
Z (STOP) Switches the unit ON or OFF. Stops playback. b Disc Tray i z/M (PLAY/PAUSE) Starts playback. iPod Dock Pauses playback temporarily, press again to exit d Display window pause mode. Shows the current status of the unit. j B (OPEN/CLOSE) e VOLUME Opens or closes the disc tray. Adjusts speaker volume. k USB Port f F (FUNCTION) Connects a USB device. Changes the input source or function. l PORT. IN g C/V,(SKIP) Connects to a portable player with audio Go to next or previous file/track/chapter. outputs. Searches backward or forward (Press and hold) Tunes in the desired radio station. HT906SC-R0_BDEULL_ENG_4740.indd 10 2011-02-19 1:58:08... -
Page 11: Rear Panel
Rear panel i h g a Power cord f HDMI OUT Connects to TV with HDMI inputs. b Speakers connectors (Interface for digital audio and video) Connects the speaker cables. g OPTICAL IN c Cooling Fan Connects to optical audio equipment. d Antenna Connector h COMPONENT VIDEO (Y P )OUTPUT FM- Connects the FM wired antenna (PROGRESSIVE SCAN) e VIDEO OUT Connects to a TV with Y P inputs. Connects to a TV with video inputs. i AUX (L/R) INPUT Connects to an external source with 2 channel audio outputs. HT906SC-R0_BDEULL_ENG_4740.indd 11 2011-02-19 1:58:09... -
Page 12: Connecting
Any front position colored connection terminal on the rear of the unit. To connect the cable to the unit, press Front Front right each plastic finger pad to open the connection terminal. Insert the wire and release the finger White Front Front left pad. To connect the cable to the speakers, press each plastic finger pad to open the connection terminals on the base of each speaker. Insert the wire and release the finger pad. > Caution y Be careful to make sure children do not put their hands or any objects into the *speaker Connect the black stripe of each wire to the duct. terminals marked -(minus) and the other end *Speaker duct : A hole for plentiful bass to the terminals marked + (plus). sound on speaker cabinet (enclosure). 2. Connect the wires to the speakers. y The speakers contain magnet parts, so color Connect the other end of each wire to the irregularity may occur on the TV screen or correct speaker according to the color coding: PC monitor screen. Please use the speakers far away from either TV screen or PC monitor. HT906SC-R0_BDEULL_ENG_4740.indd 12 2011-02-19 1:58:09... -
Page 13: Positioning The System
Connecting Positioning the system F ront left speaker (L)/ Front right speaker (R): Place the front speakers to the sides of the monitor or screen and as flush with the screen The following illustration shows an example of surface as possible. positioning the system. Note that the illustrations C enter speaker: Place the center speaker above in these instructions differ from the actual unit for or below the monitor or screen. explanation purposes. S urround left speaker (L)/ Surround right For the best possible surround sound, all the speaker (R): speakers other than the subwoofer should be Place these speakers behind your listening placed at the same distance from the listening position, facing slightly inwards. position ( ). S ubwoofer: The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections. Unit HT906SC-R0_BDEULL_ENG_4740.indd 13 2011-02-19 1:58:10... -
Page 14: Connections To Your Tv
Connections to Your Component Video Connection Connect the COMPONENT VIDEO OUTPUT (PROGRESSIVE SCAN) jacks on the unit to the corresponding input jacks on the TV using component cables. Make one of the following connections, depending on the capabilities of your existing equipment. You can hear the sound through the system’s Note speakers. y Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described Unit in this manual. y Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. > Caution y Make sure the unit is connected directly to the TV. Tune the TV to the correct video input channel. y Do not connect your player via your VCR. The image could be distorted by the copy protection system. Green Blue HT906SC-R0_BDEULL_ENG_4740.indd 14 2011-02-19 1:58:10... -
Page 15: Hdmi Out Connection
- T he picture will not be displayed properly with non-HDCP device. - T his unit does not playback and TV screen is changed to black or green screen or the snow noise may occur on the screen. y If there is noise or lines on the screen, please check the HDMI cable and use a higher version cable than High Speed HDMI™ Cable. y You can fully enjoy digital audio and video signals together with this HDMI connection. > y When you use HDMI connection, you can Caution change the resolution for the HDMI output. y Changing the resolution when the (Refer to “Resolution Setting” on page 17.) connection has already been established may result in malfunctions. To solve the problem, turn off the unit and then turn it on again. y When the HDMI connection with HDCP is not verified, TV screen is changed to black or green screen or the snow noise may occur on the screen. In this case, check the the HDMI connection, or disconnect the HDMI cable. HT906SC-R0_BDEULL_ENG_4740.indd 15 2011-02-19 1:58:10... -
Page 16: Video Connection
Connecting Video Connection To connect to a TV with the SCART jack Connect the VIDEO OUT jack on the unit to the video in jack on the TV using a video cable. Connect the RCA to SCART cable form the VIDEO You can hear the sound through the system’s OUT on the rear of the unit to the SCART jack on speakers. your TV. Unit Unit Yellow HT906SC-R0_BDEULL_ENG_4740.indd 16 2011-02-19 1:58:11... -
Page 17: Resolution Setting
Connecting Video Output Resolution Setting Resolution The unit provides several output resolutions for HDMI OUT and COMPONENT VIDEO OUT jacks. You can change the resolution using [Setup] menu. Displayed resolution in display window and 1. Press n HOME. outputted resolution may different according to 2. Use A/D to select the [Setup] and press b connection type. ENTER. The [Setup] menu appears. [HDMI OUT]: 1 080p, 1 080i, 720p and 480p (or 576p) and 480i (or 576i) [COMPONENT VIDEO OUT]: 480p (or 576p) and 480i (or 576i) [VIDEO OUT]: 480i (or 576i) 3. Use W/S to select [Display] option then press D to move to the second level. 4. Use W/S to select the [Resolution] option then press D to move to the third level. 5. Use W/S to select the desired resolution then press b ENTER to confirm your selection. Note If your TV does not accept the resolution you have set on the player, you can set resolution to 480p (or 576p) as follows: Press Z STOP for more than 5 seconds. HT906SC-R0_BDEULL_ENG_4740.indd 17 2011-02-19 1:58:11... -
Page 18: Optional Equipment Connection
The unit can be used to play the music from many types of portable player or external devices. 1. Connect the portable player to the To the audio output jacks PORT. IN (PORTABLE IN) connector of the unit. of your component (TV, VCR, etc.) Connect the external device to the AUX connector of the unit. 2. Turn the power on by pressing 1 (POWER). White 3. Select the PORTABLE or AUX (L/R) INPUT function by pressing P RADIO&INPUT. Note 4. Turn on the portable player or external device If your TV has only one output for audio and start it playing. (mono), connect it to the left (white) audio jack on the unit. HT906SC-R0_BDEULL_ENG_4740.indd 18 2011-02-19 1:58:12... -
Page 19: Usb Connection
The USB function of this unit does not support some USB devices. USB device requirement y Devices which require additional program installation connected to a computer, are not supported. y Do not extract the USB device while in operation. y For a large capacity USB, it may take longer than a few minute to be searched. Removing the USB Device from the unit y To prevent data loss, back up all data. 1. Choose a different function mode or press Z STOP twice in a row. y If you use a USB extension cable or USB hub, the 2. Remove the USB device from the unit. USB device is not recognized. y Using NTFS file system is not supported. (Only FAT(16/32) file system is supported.) y This unit is not supported when the total number of files is 1 000 or more. y External HDD, Card readers, Locked devices, or hard type usb devices are not supported. y USB port of the unit cannot be connected to PC. The unit can not be used as a storage device. HT906SC-R0_BDEULL_ENG_4740.indd 19 2011-02-19 1:58:12... -
Page 20: Optical In Connection
Connect the FM Wire antenna to the FM antenna connector. To the digital optical output jack of your component Note Be sure to fully extend the FM wire antenna. Home theater speaker ez After connecting the FM wire antenna, keep it setup as horizontal as possible. Listen to sound from TV, DVD and Digital Device with 5.1(2.1 or 2)ch mode. Even in power off mode, if you press OPTICAL, then power is on and automatically changed to AUX OPT mode. 1. Connect the unit’s OPTICAL IN jack to jack on optical out of your TV (or Digital Device etc.). 2. Select the AUX OPT by using the OPTICAL. To select the AUX OPT directly. 3. Listen sound with 5.1(2.1 or 2)ch speaker. 4. To escape from AUX OPT by using the OPTICAL. Function is retuned to previous one. HT906SC-R0_BDEULL_ENG_4740.indd 20 2011-02-19 1:58:12... -
Page 21: System Setting
About help menu for Setup complete initial language selection before using the unit. English will be selected as the initial Menu Buttons Operation language. Moving to another 1. Press 1 (POWER) to turn the unit on. The menu. Move language setup menu will appear on the screen. Moving to previous Move level. Moving to next level or selecting Move menu. To exit the [Setup] x RETURN menu or [ 5.1 Close Speaker Setup]. 2. Use WSAD to select a language then press b ENTER. To confirm menu. b ENTER The confirm menu will appear. Select 3. Use AD to select the [Enter] then press b ENTER to finish the language setup. HT906SC-R0_BDEULL_ENG_4740.indd 21 2011-02-19 1:58:12... -
Page 22: Language
[1080p] enter the wrong language code, press CLEAR. Outputs 1 080 lines of progressive video. [Off (for Disc Subtitle)] [1080i] Turn off Subtitle. Outputs 1 080 lines of interlaced video. [720p] Display Outputs 720 lines of progressive video. TV Aspect [480p (or 576p)] Outputs 480 (or 576) lines of progressive video. Select which screen aspect to use based on the shape of your TV screen. [480i (or 576i)] Outputs 480 (or (576) lines of interlaced video. [4:3] Select when a standard 4:3 TV is connected. [16:9] Select when a 16:9 wide TV is connected. Display Mode The Display Mode setting works only when the TV Aspect mode is set to 4:3. [Letterbox] Displays a wide picture with bands on the upper and lower portions of the screen. HT906SC-R0_BDEULL_ENG_4740.indd 22 2011-02-19 1:58:12... -
Page 23: Audio
1. Select [5.1 Speaker Setup] on the [Audio] menu. 2. Press b ENTER. [Size] The [5.1 SPEAKER] appears. Since the speaker settings are fixed, you cannot change the settings. [Volume] Press AD to adjust the output level of the selected speaker. Front L/R : 0 ~ -5 SubWoofer, Rear L/R, Center : 5 ~ -5 [Distance] 3. Use AD to select the desired speaker. After you connected speakers to your unit, 4. Adjust options using WSAD buttons. set the Distance between the speakers and your listening point if the distance of Center 5. Returns to the previous menu by pressing x or Rear speakers is bigger than the distance RETURN. of Front speakers. This allows the sound from each speaker to reach the listener at the same time. Press AD to adjust the Distance of the selected speaker. This distance is equivalent to a difference of the distance between Center or Rear speaker and Front speakers. [Test] Select [Speaker Test Start] by using the WS and press b ENTER. Press b ENTER again to stop. Adjust the volume to match the volume of test signals memorized in the system. HT906SC-R0_BDEULL_ENG_4740.indd 23 2011-02-19 1:58:12... -
Page 24: Lock (Parental Control)
3. Select the first character using WS buttons. picture and sound. If this happens you can compensate by setting a delay on the sound so 4. Press b ENTER and select the second character that it effectively ‘waits’ for the picture to arrive: using WS buttons. this is called HD AV Sync. Use WS (on the remote 5. Press b ENTER to confirm your Area code control) to scroll up and down through the delay selection. amount, which you can set at anything between 0 and 300m sec. Rating Blocks playback of rated DVDs based on their contents. Not all discs are rated. 1. Select [Rating] on the [Lock] menu then press 2. Input a password and press b ENTER. 3. Select a rating from 1 to 8 using the WS buttons. [Rating 1-8] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. [Unlock] If you select unlock, parental control is not active and the disc plays in full. 4. Press b ENTER to confirm your rating selection. HT906SC-R0_BDEULL_ENG_4740.indd 24 2011-02-19 1:58:13... -
Page 25: Others
4. Press n HOME to exit the menu. [Deregister] Note Deactivate your player and display the deactivation code. If you forget your password, you can clear it using the following steps: Note 1. Select the [Setup] menu on the [Home All the downloaded videos from DivX VOD can Menu]. only be played back on this unit. 2. Input the 6-digit number “210499” and press b ENTER. The password is cleared. Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 40. 1. Select [Area Code] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select the first character using WS buttons. 4. Press b ENTER and select the second character using WS buttons. 5. Press b ENTER to confirm your Area code selection. HT906SC-R0_BDEULL_ENG_4740.indd 25 2011-02-19 1:58:13... -
Page 26: Operating
1. Insert the disc by using the B OPEN/CLOSE or Displays the [Home Menu]. Connect the USB device to the USB port. 2. Press n HOME. Displays the [Home Menu]. 3. Select an option by using AD. If you select the [Movie], [Photo] or [Music] option when you connect up to two devices, 2. Select an option by using AD. it appears as belows. Select a media then press 3. Press b ENTER then selected option menu. b ENTER. [Music] – Displays [MUSIC] menu. [Movie] – S tart video media’s playback or displays the [MOVIE] menu. 4. Press b ENTER then selected option menu. [Photo] – Displays [PHOTO] menu. Note [Setup] – Displays the [Setup] menu. y For the most Audio CD and DVD-ROM discs, Note playback starts automatically. You can not select the [Music], [Movie] or y The unit plays only music file contained in [Photo] option when the USB device is not the USB storage device or disc automatically. connected or a disc is not inserted. HT906SC-R0_BDEULL_ENG_4740.indd 26 2011-02-19 1:58:13... -
Page 27: Other Operations
Angle – S elected angle/ total number of angles. To return to normal speed, fast forward or Note press d PLAY, MONO/ fast reverse STEREO. If any button is not pressed for a few seconds, the on-screen display disappears. Press h REPEAT repeatedly, and the current title, chapter or track will be played back Playing repeatedly or randomly. repeatedly or - DVD : Chapter/ Title/ Off randomly - DivX : Title/ All/ Off - A udio CD/ MP3/ WMA : Track/ All/ Random/ Off In the pause mode, press Slowing down SLOW (c or v) to select the playing the required speed. (DVD, DivX speed only) The DivX file cannot be slow down reverse playback. HT906SC-R0_BDEULL_ENG_4740.indd 27 2011-02-19 1:58:13... -
Page 28: To Display The Dvd Menu
1. During playback, press d PLAY, MONO/ (from the scene point). STEREO to play at 1.5 times speed. “dX1.5” If you press Z STOP twice or unload the disc, appears on the screen. “Z”(Complete Stop) appears on the screen. The 2. Press d PLAY, MONO/STEREO again to exit. unit will clear the stopped point. Note Screen Saver The resume point may be cleared when a button is pressed (for example; 1 (POWER), The screen saver appears when you leave the unit B OPEN/CLOSE, etc). in Stop mode for about five minutes. Changing subtitle code page If the subtitle is not displayed properly, you can change the subtitle code page to view the subtitle file properly. 1. During playback, press m INFO/DISPLAY to display the On-Screen display. 2. Use WS to select the [Code Page] option. 3. Use AD to select desired code option. 4. Press x RETURN to exit the On-Screen display. HT906SC-R0_BDEULL_ENG_4740.indd 28 2011-02-19 1:58:13... -
Page 29: Marked Playback
(MP3/ WMA only) Note File information will be displayed The markers are also cleared when the disc or according to the ID3TAG information USB device is removed, the unit is switched to on the appropriate music file. (MP3 power off or the function is switched to others. only) Selecting all tracks/ files. Deselecting all tracks/files. Moving to the previous or next file list. 2. Select a desired music on the [List] by using the then press MARKER to appears the mark on the list. PLAY, MONO/STEREO. 3. Press ENTER or Displays the play mode. 4. Select the play mode by using the and press ENTER. [Mark Play] Marked playback. [Current Play] Normal playback. Note If you want to select all files on the list, select [Select All] and press b ENTER. HT906SC-R0_BDEULL_ENG_4740.indd 29 2011-02-19 1:58:13... -
Page 30: Viewing A Photo File
or pause slide show. wsad Moving to another WSAD c Speed x3/ x2/ x1 – Use ENTER to select Move file or content. a delaying speed between photos in a slide Viewing a particular show. b ENTER Select file. d Rotate – Press ENTER to rotate the photo. Returning to the x RETURN Close [Home Menu]. e Go to list – Press ENTER to return [Photo] menu. HT906SC-R0_BDEULL_ENG_4740.indd 30 2011-02-19 1:58:13... -
Page 31: Sleep Timer Setting
Unit turns off. Press SLEEP The remaining time appears in the display window. Dimmer Press SLEEP once. The display window will be darken by half. To cancel it, press SLEEP repeatedly until dim off. Turn off the sound temporarily Press MUTE to mute your unit. You can mute your unit in order, for example, to answer the telephone, appears the MUTE in the display window. Last Scene Memory This unit memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. System Select - Optional You must select the appropriate system mode for your TV system. Press and hold M PAUSE/STEP for more than five seconds to be able to select a system in the [Home Menu]. Note If the USB device is connected or a disc is inserted, this function is not operated. HT906SC-R0_BDEULL_ENG_4740.indd 31 2011-02-19 1:58:13... -
Page 32: Radio Operations
3. Press b ENTER a preset number will flash in This text may scroll across the display. the display window. CT ( Time controlled by the channel) 4. Press PRESET (-/+) to select the preset number This shows the time and date as you want. broadcast by the station. 5. Press b ENTER. You can search the radio stations by programme The station is stored. type by pressing RDS. The display will show the last 6. Repeat the steps 2 to 5 to store other stations. PTY in use. Press PTY one or more times to select your preferred programme type. Press AD. The tuner will search automatically, when a station is Deleting all the saved stations found the search will stop. 1. Press and hold CLEAR for two seconds. “ERASE ALL” will flash up on the unit display. 2. Press CLEAR to erase all saved of the radio stations. HT906SC-R0_BDEULL_ENG_4740.indd 32 2011-02-19 1:58:13... -
Page 33: Sound Adjustment
In some of surround modes, some speakers, there’s no sound or low sound. It depends Realizes the sound equalizer on the mode of surround and the source of that is the most similar to the AUTO EQ genre of which is included in audio, it is not defective. the MP3 ID3 tag of song files. y You may need to reset the surround mode, after switching the input, sometimes even This program lends an after the sound track changed. enthusiastic atmosphere to CLASSIC the sound, giving you the feeling you are at an actual JAZZ rock pop, jazz or classic ROCK concert. The BASS is Bass Blast. During playback, reinforce the treble, BASS bass and surround sound effect. The CLRVOICE is Clear Voice. This program make voice sound clear, improving the CLRVOICE quality of voice sound. (We encourage to use this EQ when you watch the movie of 5.1 channel.) HT906SC-R0_BDEULL_ENG_4740.indd 33 2011-02-19 1:58:13... -
Page 34: Advanced Operations
When you stop recording during playback, Audio CD the file will not be stored. y In the state CD-G, DTS disc USB record is not operated. MP3/ WMA y The files in the sub-folders are not recorded during all track recording. y You may not record more than 999 files. y The numbering of the recording file is The other entered from the lowest number. So if you sources (Tuner, delete some of the recording files, the next AUX, Portable) recording file could be the lowest number among them. The making of unauthorized copies of copy- protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. Be responsible Respect copyrights. HT906SC-R0_BDEULL_ENG_4740.indd 34 2011-02-19 1:58:13... -
Page 35: Playing The Ipod
C onnect the iPod firmly. To open the iPod Dock, pull iPod dock. You can enjoy the media files with your iPod. For details about iPod, refer to the iPod’s User Guide. Preparation y To view iPod’s Videos and Photos on the TV screen. - Be sure to use the video connection through the VIDEO OUT jack on the rear panel of this unit. Select the appropriate video input mode on the TV. - Depending on the iPod, make sure that select y If you turn this unit on, your iPod is automatically Videos > Video settings, and then set TV Out turned on and recharging starts. to Ask or On from your iPod. y If your iPod is completely discharged, charge the For details about Video Settings, refer to the battery first. iPod User Guide. - The viewing photos is available only if this unit is in iPod IN mode and you can view photos only as a slide show. You have to start a slide show on your iPod to view a photo on a TV. For details about a slide show, refer to the iPod User Guide. y Before connecting the iPod, turn this unit off and reduce the volume of this unit to its minimum. HT906SC-R0_BDEULL_ENG_4740.indd 35 2011-02-19 1:58:14... -
Page 36: Enjoying Ipod On The Screen
ENTER to play. MONO/STEREO again. File information will be displayed Fast-forward or rewind a song c/v SCAN according to the ID3TAG information or video on the appropriate music file. (MP3 only) C/,V Skip the playback forward or SKIP backward . To select a desired repeat h REPEAT mode: Track ( ), All ( ), Off (No display). Moving to the previous or next file list. 5. Operate iPod. Refer to basic operation section. Note y If the iPod’s OSD language is selected to simple chinese, the power scroll function is not operated correctly. y The controls on your iPod are not operational in this mode. HT906SC-R0_BDEULL_ENG_4740.indd 36 2011-02-19 1:58:14... - Page 37 - the communication between this unit and your iPod is failed. > U ndock & re-dock your iPod in this unit. - your iPod is not connected firmly. - this unit recognizes your iPod as unknown device. - your iPod is exceptionally low on power. > The battery needs to be charged. > I f you charge the battery while iPod is extremely low in power, it maytake longer to charge. y You may use the dock adapter which should be supplied with your iPod to the dock for the stable use of the iPod. If you need an adapter, consult your iPod dealer. y Compatibility with your iPod may vary depending on the type of your iPod. y iPod touch and iPhone have any difference in operation other than iPod. You may need any additional control to use them with this unit. (e.g. “slide to unlock”) y If you use an application, make a call, or send and receive SMS text message, etc. on iPod touch or iPhone, disconnect it from iPod dock of this unit and then use it. HT906SC-R0_BDEULL_ENG_4740.indd 37 2011-02-19 1:58:14...
-
Page 38: Troubleshooting
No picture Connect the video cables securely to both the TV and unit. Select the correct input mode of the unit so you can hear the sound from the unit. There is little or no sound Connect the audio cables into the connection terminals correctly. Replace with a new audio cable. Clean the disc using a soft cloth with outward strokes. The DVD picture quality is poor Insert a disc. Insert a playable disc (check the disc type, colour system and regional code). A DVD/CD will not play Place the disc with the label or printed side facing upwards. Enter your password or change the rating level. Clean the disc using a soft cloth with outward strokes. Humming noise heard while a DVD or CD is playing Move unit and audio components further away from your TV. Check the antenna connection and adjust its position. Attach an external aerial if necessary. Radio stations can’t be tuned in properly Tune to the station manually. Preset some radio stations, see page 32 for details. The remote is not pointed directly at the unit. Point the remote directly at the unit. The remote is too far from the unit. Use the remote within 23 feet (7m) of the unit. The remote control doesn’t work There is an obstacle in the path between the remote control and well / at all the unit. Remove the obstacle. The battery in the remote control are flat. Replace the battery with new ones. HT906SC-R0_BDEULL_ENG_4740.indd 38 2011-02-19 1:58:14... -
Page 39: Appendix
Do not use volatile liquids such as insecticide sunlight. spray near the unit. y Wiping with strong pressure may damage the Cleaning Discs surface. Fingerprints and dust on the disc can cause poor y Do not leave rubber or plastic products in picture quality and sound distortion. Before playing, contact with the unit for a long period of time. clean the disc with a clean cloth. Wipe the disc from the center to out. Cleaning the unit Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, To clean the player, use a soft, dry cloth. If the or anti-static spray intended for older vinyl records. surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Maintaining the Unit The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center. HT906SC-R0_BDEULL_ENG_4740.indd 39 2011-02-19 1:58:14... -
Page 40: Area Code List
Colombia Italy Paraguay Uganda Congo Jamaica Philippines Ukraine Costa Rica Japan Poland United States Croatia Kenya Portugal Uruguay Czech Republic Kuwait Romania Uzbekistan Denmark Libya Russian Vietnam Federation Ecuador Luxembourg Zimbabwe Saudi Arabia Egypt Malaysia Senegal El Salvador Maldives Ethiopia Mexico HT906SC-R0_BDEULL_ENG_4740.indd 40 2011-02-19 1:58:14... -
Page 41: Language Code List
Esperanto 6979 Kurdish 7585 Scots Gaelic 7168 Xhosa 8872 Estonian 6984 Laothian 7679 Serbian 8382 Yiddish 7473 Faroese 7079 Latin 7665 Serbo-Croatian 8372 Yoruba 8979 Fiji 7074 Latvian, Lettish 7686 Shona 8378 Zulu 9085 Finnish 7073 Lingala 7678 HT906SC-R0_BDEULL_ENG_4740.indd 41 2011-02-19 1:58:14... -
Page 42: Trademarks And Licenses
Please note that the use of this accessory with DivX®, DivX Certified® and associated logos are iPod, iPhone may affect wireless performance. trademarks of DivX, Inc. and are used under license. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that plays DivX video. What is SIMPLINK? Visit www.divx.com for more information and Some functions of this unit are controlled by software tools to convert your files into DivX TV’s remote control when this unit and LG TV video. with SIMPLINK are connected through HDMI ABOUT DIVX VIDEO-ON-DEMAND: This DivX connection. Controllable functions by LG TV’s Certified® device must be registered in order to remote control; Play, Pause, Scan, Skip, Stop, play purchased DivX Video-on-Demand (VOD) Power Off, etc. movies. To obtain your registration code, locate y Refer to the TV owner’s manual for the details the DivX VOD section in your device setup menu. of SIMPLINK function. Go to vod.divx.com for more information on how y LG TV with SIMPLINK function has the logo as to complete your registration. shown above. y Use a higher version cable than High Speed HDMI™ Cable. HT906SC-R0_BDEULL_ENG_4740.indd 42 2011-02-19 1:58:15... -
Page 43: Specifications
Operating temperature 41 °F to 95 °F (5 °C to 35 °C) Operating humidity 5 % to 90 % Bus Power Supply (USB) DC 5 V 0 500 mA Inputs/ Outputs VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 COMPONENT VIDEO OUT (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 HDMI OUT (video/audio): 19 pin (Type A, HDMI™ Connector ) ANALOG AUDIO IN 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1 DIGITAL IN (OPTICAL): 3 V (p-p), Optical jack x 1 PORT. IN 0.5Vrms (3.5 mm stereo jack) Amplifier Stereo mode 180 W + 180 W (4 Ω at 1kHz) Front 180 W + 180 W (4 Ω at 1 kHz) Center 180 W (4 Ω at 1 kHz) Surround mode Surround 180 W + 180 W (4 Ω at 1 kHz)) Subwoofer 200 W (3 Ω at 60 Hz) Tuner FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz HT906SC-R0_BDEULL_ENG_4740.indd 43 2011-02-19 1:58:15... - Page 44 180 W Max. Input Power 360 W Net Dimensions (W x H x D) 94 X 182 X 83 mm Net Weight 0.61 kg Centre Speaker Type 2 Way 3 speaker Impedance Rated 4 Ω Input Power 180 W Max. Input Power 360 W Net Dimensions (W x H x D) 327 x 99 x 76 mm Net Weight 1.21 kg Passive Subwoofer Type 1 Way 1 Speaker Impedance Rated 3 Ω Input Power 200 W Max. Input Power 400 W Net Dimensions (W x H x D) 190 X 385 X 318 mm Net Weight 5.18 kg Design and specifications are subject to change without notice. HT906SC-R0_BDEULL_ENG_4740.indd 44 2011-02-19 1:58:15...
- Page 45 HT906SC-R0_BDEULL_ENG_4740.indd 45 2011-02-19 1:58:15...