Table of Contents
Advertisement
Changing the basic settings
Your appliance has various basic settings which you can
change at any time.
Basic settings
In the table, you will find all the basic settings and options for
changing them.
Basic setting
Clock display
™‚
= on
‚
Signal duration
™ƒ
= medium = 2 minutes
ƒ
Button tone
™„
‚
= on
Waiting time
™...
ƒ
= medium = 5 seconds
Prerequisite: your appliance is switched off.
Press and hold the
0
button for a few seconds.
1.
The first basic setting appears in the display.
You can change the basic setting by turning the rotary
2.
selector.
Care and cleaning
With careful care and cleaning your microwave oven will retain
its looks and remain good order. We will explain here how you
should care for and clean your appliance correctly.
:
Risk of electric shock.!
Penetrating moisture may cause an electric shock. Do not use
any high-pressure cleaners or steam cleaners.
:
Risk of burns!
Never clean the appliance immediately after switching off. Let
the appliance cool down.
:
Risk of injury!
Scratched glass in the appliance door may develop into a
crack. Do not use a glass scraper, or sharp or abrasive
cleaning aids or detergents.
Notes
Slight differences in colour on the front of the appliance are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Unpleasant odours, e.g. after fish has been prepared, can be
■
removed very easily. Add a few drops of lemon juice to a cup
of water. Place a spoon into the container as well, to prevent
delayed boiling. Heat the water for 1 to 2 minutes at
maximum microwave power.
10
Options
Clock display
= off
ƒ
= short = 10 seconds
‚
= long = 5 minutes
„
Button tone
ƒ
= off
‚
= short = 2 seconds
= long = 10 seconds
„
Confirm by pressing the
3.
The next basic setting appears in the display. You can go
through all of the basic settings with the
changes with the rotary selector.
To finish, press and hold the
4.
All settings are applied.
You can change the settings at any time.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
■
metal or glass scrapers to clean the glass in the appliance
■
door,
metal or glass scrapers to clean the door seal,
■
any coarse scouring pads or cleaning sponges,
■
cleaning agents with high concentrations of alcohol.
■
Wash new sponge cloths thoroughly before use.
Area
Appliance front
Stainless steel
Explanation
Displays the clock
Audible signal after the cooking time has
elapsed
Confirmation tone when a button is pressed
Waiting time between two separate steps,
after setting
button.
0
0
button for a few seconds.
Cleaning agents
Hot soapy water:
Clean using a dish cloth and then dry
with a soft cloth. Do not use glass clean-
ers or metal or glass scrapers for clean-
ing.
Hot soapy water:
Clean using a dish cloth and then dry
with a soft cloth. Remove flecks of
limescale, grease, starch and albumin
(e.g. egg white) immediately. Corrosion
can form under such residues. Special
stainless steel cleaning agents can be
obtained from the after-sales service or
from specialist retailers.
0
button and make
Advertisement
Table of Contents
