Table of Contents
Advertisement
Menu operation (continued)
INSTALLATION 1 menu
INSTALLATION 1
2
1
ITEM
LAMP MODE
LAMP SELECT
LAMP RELAY
STANDBY MODE
IMAGE REVERSE
HIGH ALTITUDE MODE
COOLING CONDITION
TEST PATTERN
LENS LOCK
ZOOM/FOCUS LOCK ON / OFF
LENS SHIFT LOCK
LENS SHIFT RESET
• Regardless of the setting of LAMP MODE, the STANDARD lamp mode is activated by default whenever the projector is turned
on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.
• When the lamp mode is switched, the projected image may flicker.
• Frequent switching of the lamp mode may damage the lamp.
• When using the projector for a long time, set LAMP RELAY.
• To cancel the test pattern, press any button other than the TEST PATTERN button on the remote control.
• While the lamps are being switched, an icon
being displayed, you cannot set LAMP SELECT and LAMP RELAY.
• After you switch the lamps and the newly selected lamp turns on, you cannot turn off the projector for approx. 1 minute.
opt.
1
1
2
2
LAMP MODE
STANDARD
LAMP SELECT
DUAL
LAMP RELAY
1H/24H
STANDBY MODE
LOW
IMAGE REVERSE
OFF
HIGH ALTITUDE MODE
STANDARD
COOLING CONDITION
0°
TEST PATTERN
CROSS HATCH
LENS LOCK
ENTER
SETTING
STANDARD
LOW
DUAL
SINGLE
LAMP 1
LAMP 2
DUAL: OFF
1H/24H
/
2H/1W
SINGLE:OFF
24H
/
1 WEEK
STANDARD
LOW
OFF
MIRROR
INVERT
MIRROR INVERT
STANDARD
HIGH ALTITUDE
0°
/ 45°
/ 90°
/
135°
/ 180°
/
225°
/ 270°
/
315°
CROSS HATCH
WHITE
BLACK
H. COLOR BARS
V. COLOR BARS
ENTER
ON / OFF
OK
1
1
INSTALLATION 1
LENS LOCK
ZOOM/FOCUS LOCK
LENS SHIFT LOCK
LENS SHIFT RESET
FUNCTION
Select this option when you want to view images in a well-lit room.
Select to moderate the intensity of the lamp. The operating sound is reduced
and the lamp lifetime becomes longer.
LAMP 1 and LAMP 2 illuminate.
The lamp with shorter operation time is automatically selected at power-on.
LAMP 1 illuminates. (When it is broken or dead, LAMP 2 illuminates automatically.)
LAMP 2 illuminates. (When it is broken or dead, LAMP 1 illuminates automatically.)
The LAMP RELAY doesn't work.
Use to set the lamp relay interval. (See page 53.)
The LAMP RELAY doesn't work.
Use to set the lamp relay interval. (See page 54.)
Select this option when you control the projector via the LAN, REMOTE 1 IN,
and SERIAL OUT terminal during power standby.
Select this option when you don't control the projector via the LAN, REMOTE
1 IN, and SERIAL OUT terminal during power standby. This option disables
the LAN, REMOTE 1 IN, and SERIAL OUT terminal and reduces the power
consumption during the power standby.
Select when viewing images from the front with the projector installed on the
floor.
Select when viewing images projected from the behind of the screen with the
projector installed on the floor.
Select when viewing images projected from the behind of the screen with the
projector installed on the ceiling.
Select when viewing images from the front with the projector installed on the
ceiling.
Select this option for normal use.
Select this option for use at an altitude of 2000 to 2700 meters above the sea
level.
The cooling condition changes according to the selected projection angle.
(See page 13.)
Select to show the test cross hatch pattern.
Select to show the maximum brightness image.
Select to show the minimum brightness image.
The horizontal color bar pattern is displayed.
The vertical color bar pattern is displayed.
The LENS LOCK menu is displayed for the following settings.
Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
Use to enable or cancel the LENS SHIFT LOCK.
Use to reset the position of the lens to the factory setting.
is displayed to the right of the INSTALLATION 1 menu bar. While the icon is
EN-34
opt.
2
2
OFF
OFF
OK
Advertisement
Table of Contents
