Related Manuals for Prorack K1006
Summary of Contents for Prorack K1006
- Page 1 K1006 Fitting Kit Fitting Instructions for Basic Carrier Revision No: 2B...
- Page 2 Fitting Kit K1006 MAX kgs (lbs) Renault Talisman, 4dr Sedan 16-+ 75 kgs (165 lbs) 80 kgs (176 lbs)
- Page 3 Fitting Kit K1006 Talisman, 4dr Sedan 16-+ (EU) -290mm 420mm 950mm 910mm -11 -7/16ths" 16 9/16ths" 37 3/8ths" 35 13/16ths"...
-
Page 4: First Time Installation
Fitting Kit K1006 First Time Installation Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. This kit fits type A, B, C and D. These instructions show type A crossbar fitted. They also apply to type B, C and D. - Page 5 Fitting Kit K1006 Use keys to remove covers. Use hex screwdriver to reverse adjusting screw 10 turns. Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. Ensure each end of the crossbar is...
- Page 6 Fitting Kit K1006 Remove locking screw. Apply protective strip as shown. Trim if required. Refer to the underside of the pad for the part number.
- Page 7 Fitting Kit K1006 It is important to put the pads in the correct position on the vehicle. Letters refer to the pad part numbers and position. Pad Part Number: A = 262 B = 261 C = 240 Place rubber pads (supplied with fitting kit) on the vehicle roof.
- Page 8 Fitting Kit K1006 It is important to put the clamps in the correct position on the vehicle. Letters refer to the part numbers stamped on clamps. Clamp Part Number: A = B880 B = B881 C = C882 D = C883 Attach clamp to each leg.
- Page 9 Fitting Kit K1006 Fitment Clamps directly to edge of roof under the doors Please check the front of this manual for information relating specifically to your vehicle. Place crossbar on vehicle. Minimum recommended spacing between the bars is 700mm (27 1/2") (unless otherwise stated).
- Page 10 Fitting Kit K1006 Adjust the legs on the crossbar so that they are positioned equally from the ends of the crossbar, and the clamps engage firmly on the body work of the vehicle. Locate vehicle's fixed points. Clamps directly to edge of roof under the doors, pin located in hole on vehicle.
- Page 11 Fitting Kit K1006 Check crossbar is securely attached to the vehicle. Please take care when closing the doors as contact can be made with the clamp if it is not installed correctly. Close the door slowly upon first inspection. Use keys to fit and lock covers CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars.
-
Page 12: Maintenance
Fitting Kit K1006 Maintenance Clean the car roof and surfaces of the product that will be in contact with the car roof. Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. - Page 13 Fitting Kit K1006 Check and replace worn out or defective parts. Keep the product clean and maintained. Never drive into a car wash with the roof rack system fitted. Lubricate locks and adjusting screws at regular intervals. Remove the products from the vehicle when not in use.
-
Page 14: Warranty And Disclaimer
Make a claim as soon as practicable by contacting the Prorack dealer from whom you purchased the product, who will give you instructions on how to proceed. If you are unable to contact the Prorack dealer, or the dealer is not able to remedy the defect, you should contact Yakima as soon as practicable at: Call: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: warranty@yakima.co.nz or warranty@yakima.com.au... - Page 15 Yakima or the Prorack dealer will be borne by you. Following receipt of the product and purchase invoice or receipt, Yakima or the Prorack dealer must inspect the product to determine whether the claim falls within the warranty. If: 4.1 the claim falls within the warranty, Yakima will remedy any defects in materials or workmanship becoming apparent during the...