Aurora AU-A1VGSZ5E/19 Quick Start Manual

MODEL
‫النموذج‬
/ REFERENCE / ARTIKELNR / MODELO /
VOLTAGE (V)
/ TENSION D'ALIMENTATION / EINGANGSSPANNUNG / VOLTAJE /
SUPPLY FREQUENCY
/ FREQUENCE D'ALIMENTATION / EINGANGSFREQUENZ /
‫تردد التيار المغذي‬
FRECUENCIA DE SUMINISTRO /
POWER CONSUMPTION
‫إستهالك الطاقة‬
/ PUISSANCE / LEISTUNG / CONSUMO DE ENERGÍA /
POWER FACTOR
/ FACTEUR DE PUISSANCE / LEISTUNGSFAKTOR / FACTOR DE POTENCIA /
LUMENS
‫كمية الضو‬
/ FLUX / LUMEN / LUMENS /
CCT
‫درجة ح ر ارة الضوء‬
/ CCT / FARBTEMPERATUR / CCT /
LAMP BASE
‫قاعدة اللمبة‬
/ CULOT / SOCKEL / BASE DE LA LÁMPARA /
DIMENSIONS (Ø x H)
‫المقاسات‬
/ DIMENSIONS / MASSE / DIMENSIONES /
START TIME
/ DUREE DE MISE EN FONCTIONNEMENT / STARTZEIT / HORA DE INICIO /
STAND BY POWER
/ CONSOMMATION EN VEILLE / STANDBY-POWER
‫الطاقة الجاهزة‬
/ ENERGÍA DE RESERVA /
MAX. OUTPUT RF POWER
/ PUISSANCE HF RAYONNEE MAX / MAX. BETRIEBS-STROMVERBRAUCH
‫أقصى طاقة خارجة من الترددات الالسلكية‬
/ MAX. POTENCIA DE RF DE SALIDA /
MAX. NUMBER OF DEVICES
/ NOMBRE MAXIMUM D'APPAREILS / MAX. ANZAHL GERÄTE
‫أقصى عدد من األجهزة‬
/ MAX. NÚMERO DE DISPOSITIVOS /
STANDARD OPERATING TEMPERATURE
/ TEMPERATURE DE FONCTIONNEMENT / STANDARD BETRIEBSZEIT
‫درجة الح ر ارة النموزجية للتشغيل‬
/ TEMPERATURA DE FUNCIONAMIENTO ESTANDAR /
IP RATING
/ CLASSIFICATION IP / IP KLASSIFIZIERUNG / CLASIFICACIÓN IP /
PROTOCOL
‫بروتو كول‬
/ PROTOCOLE / PROTOKOLL / PROTOCOLO /
FREQUENCY BAND
/ BANDE DE FREQUENCES / FREQUENZSPANNE
‫حزمة الترددات‬
/ BANDA DE FRECUENCIA /
AU-A1VGSZ5E/19, AU-A1VG125Z5E/19, AU-A1VST64Z5E/19
220-240V
‫الجهد الكه ر بي‬
50/60Hz
4W
0.5
‫معامل الطاقة‬
380lm
1900K
E27
60mm x 120mm (AU-A1VGSZ5E/19)
125mm x 195mm (AU-A1VG125Z5E/19)
64mm x 160mm (AU-A1VST64Z5E/19)
0.5s
‫وقت البدأ‬
0.5W
10 dBm/mW
Depends on Hub
Fonction du Hub / Abhängig von Hub
‫يعتمد على مر كز اإلتصال‬
/ Depende del Hub /
-20°C to 25°C
IP20 (Use in dry locations only)
IP20 (Utilisation uniquement en locaux non humide)
IP20 (Nur für trockene Umgebungen geeignet)
‫درجة الحماية‬
IP20 (Usar solo en lugares secos)
)‫(لإلستخدام فقط داخل األماكن الجافة‬ ‫درجة الحماية‬
20
Zigbee 3.0
2.40 Ghz - 2.483 Ghz
auroralighting.com
GB
Setting up your Smart Lamp
1
Ensure you have downloaded the AOne App and you have the AOne Hub
(AU-HZB5A) installed before trying to add devices.
2
We recommend only pairing one lighting circuit at a time otherwise, there
is a risk other smart devices will be found on other lighting circuits.
3 Ensure the wall switch for the lighting circuit is switched off before fitting
the lamp. Your Aurora Smart lamp is fitted in the same way that traditional
household lamps are fitted. Once fitted, ensure the lamp is switched off until
you are ready to pair your devices.
4
Open your App and go to the 'add devices' icon.
Turn the lamp on, it should automatically flash twice showing it is in pairing
mode. The lamps should automatically show on the App pairing screen.
Ensure all lamps on the circuit have been discovered.
5
If any devices have not been found. Press 'Done' and delete all the devices
and reset the lamps by switching off/on six times. After the sixth time they
should flash three times. Follow Step 4 to pair your lamps again.
6
Once complete, follow advice on the App to control your lights, create
spaces, schedules and scenes.
Remember
To turn your Aurora Smart Lamp on or off remotely it must be switched on at
the wall/fixture. Your Aurora Smart Lamp should not be dimmed using a wall
mounted dimmer switch as it may cause buzzing or flickering. Keep away from
liquids and humidity, Use in dry locations only. Not suitable for emergency lighting.
For lamps with a weight significantly higher than that of the lamps for which they
are a replacement, attention should be drawn to the fact that the increased weight
may reduce the mechanical stability of certain luminaires and lampholders and
may impair contact making and lamp retention.
The lamp is based on protocol Zigbee 3.0, to control on/off and brightness dimming, it
must be controlled through the App. This product is not suitable for a dimming circuit.
Maintenance
Before replacing lamp, turn off the mains power and let lamps cool to avoid
electrical shock or burns.
Disconnect your Aurora Smart Lamp before cleaning and keep it away from water
and other liquids at all times.
The Aurora Smart Lamp does not contain any serviceable parts so do not attempt to open it.
RED Compliance
There are no restrictions of use.
Hereby, Aurora Limited declares that the radio equipment type
listed within this guide are in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address:
auroralighting.com
Document Version: AU-A1ZB_GLS_FILAMENT_V2_19 (MULTILINGUAL)
Aurora Limited
6 Little Burrow, Burrowfields,
Welwyn Garden City,
AL7 4SW, United Kingdom