ConnectGear XG2 User Manual

Trouble Shooting:

•Possible reasons for not compatible with
XG2 2-Port Mini KVM Switch
1.The BIOS in the mother board.(Basic Input/Ouput
System).
2.The hardware equipment.(Keyboard.Mouse)
3.Software.OS(Operating System)
SITUATION SOLUTION
•Check whether the correct mouse
driver was installed.
•Change to other mouse.
(PS/2 mouse only for user side)
Mouse Hanged
•Connect the mouse to PC directly.
•Change to the PC port.
•Try to select other port and then
switch back.
•Change to other keyboard.
•Connect the keyboard to PC directly.
Keyboard Hanged
•Change to the PC port.
•Try to select other port and then
switch back.
•Do not move keyboard, mouse or
select PC if the initial turn-on
operation procedure is not completed.
Improper Operation •Reboot after the PC is turned off for
5 seconds later.
•Try to select other port and then
switch back.

SPECIFICATIONS:

SPECIFICATION
XG2
2 PCs to 1 User
PLASTIC CASE
Yes

Transmission Distance

16ft (5m)
10ft (3m)
Built-in with 4ft (1.2m) Coaxial cable
43-120Hz
1600 x 1200
200MHz
30-100KHz

Limited Warranty:

N NO EVENT THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE
I
PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL,
INCIDENTAL,OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THE PRODUCT, DIST, OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed,
implied, or statutory with respect to the contents or use of this
documentation, and specially disclaims its quality, performance,
merchantability, or fitness for any particular purpose. The direct
vendor also reserves the right to revise or update device or
documentation without obligation to update. For further
please contact your direct vendor.
Preventing Radio & TV Interference:
WARNING!!! This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used
in accordance with the instructions MANUAL, may cause
interference to radio communications. It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of part 15 of FCC Rules, which
are designed to provide reasonable protection against such
interference when operated in a commercial environment.
Operations of this equipment in a residential area is likely to
cause interference in which case the user at his own expense
will be required to take whatever measures may be required
to correct the interference.

INSTALLATION:

OPERATION:

1.First turn on the monitor followed by the PCs.
2.Make sure each PC is boot-up completely before
switching the KVM Switch.

To activate the scan mode(Auto status):

Scroll Scroll
*Hot Key operation :
Lock Lock

To deactivate the scan mode (Manual status):

*Press ESC on the keyboard.

To select PC:

Scroll Scroll
*Hot Key operation:
Lock Lock
2 PORT AUTO 2 PORT AUTO
2 PORT AUTO
with Built-in cables
with Built-in cables with Built-in cables
inquires
USER'S MANUAL
XG2
Please read this manual thoroughly and follow the
instruction procedures to prevent any damage to the
CPU SWITCH and or the connecting devices.
LED:
After the computers are turned on, the front panel shows:
PC1/PC2 LED : The LED will be lit for the PC
which is selected or scanned.
AUTO LED : Lit when in Auto Scan mode.

Adjust the SCAN TIME:

1. 5 sec Default setting .
Scroll Scroll
2. Press into the Auto Scan mode.
Lock Lock
3. Press or to choose the scan rate.
+
Num Lock
SCAN RATE
LED
5 sec.
OFF
10 sec.
ON
15 sec.
ON
20 sec.
OFF
25 sec. OFF
30 sec.
ON
*Note:If the power was turned off,tfe scan rate will
ESC
back to the default setting-5 seconds.
KVM KVM
KVM
MINI
MINI MINI
Caps Lock Scroll Lock
LED LED
ON
OFF
OFF OFF
OFF ON
ON OFF
ON ON
ON OFF