Canon RealIS SX80 Mark II Supplementary Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Projector
  5. REALiS SX80 Mark II D
  6. Supplementary manual

Canon RealIS SX80 Mark II Supplementary Manual

Canon realis sx80 mark ii: supplementary guide
Hide thumbs Also See for RealIS SX80 Mark II:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Canon
SX80
Summary of Remote Control Commands (User Commands)
1. Connection
Use the cable to connect the projector (service port) to the computer (RS-232C serial port).
The computer and projector should be connected in a direct, 1:1 connection.
If the number of pins on the connectors or the formats do not match, an adapter is required.
COM
Port
Computer
Dedicated cable

2. Communication Format

Item
Specifications
RS-232-C start-stop synchronization, semi-duplex communication
Communication Method
19200 bps
Transmission Speed
8 bits
Character Length
2 bits
Stop Bit
None
Parity
None
Flow Control
Item
Specifications
Variable-length (up to 256 bytes including delimiter)
Number of Bytes
CR, LF, CR+LF, or null (00h)
Delimiters
In messages, CR is indicated as <CR>, LF as <LF>, CR+LF as <CR>+<LF>, and null as <00>.
ASCII code (typical characters: 20h to 7Fh)
Message Codes
Case-insensitive.
<CR> is 0Dh, <LF> is 0Ah, <CR>+<LF> is 0Dh0Ah, and <00> is 00h.
Protocol
No protocol
None
Flow Control
None
Error Control
Not supported
Break Signal
Between characters
<1 byte>
Period between command and response: 10 seconds
Timeout
Computer
Within 10 seconds
The next command must not be sent without waiting for the response
If the next command is sent, an error will occur
Service
Port
Canon
Projector
: 5 seconds
(However, timeout between CR and LF is 10 ms)
<1 byte>
Within 5 seconds
Projector
Command
Response
Item
Specifications
Connection Method
Computer: Directly connected to the projector (1:1)
Signal Lines to Connec
Three-line connection: SD, RD, and SG
Cable to Connect
9-pin RS-232C cable (cross)
Send Data SD
SD Send Data
Receive Data RD
RD Receive Data
Signal Ground SG
SG Signal Ground
* In the SX80, only the three signal lines of SD, RD, SG are used

Advertisement

Table of Contents
loading

Related Manuals for Canon RealIS SX80 Mark II

Summary of Contents for Canon RealIS SX80 Mark II

  • Page 1: Communication Format

    Summary of Remote Control Commands (User Commands) 1. Connection Use the cable to connect the projector (service port) to the computer (RS-232C serial port). The computer and projector should be connected in a direct, 1:1 connection. If the number of pins on the connectors or the formats do not match, an adapter is required.
  • Page 2 Turn off the device, check the communication cable, and resend the command. Has 10 seconds elapsed? First failure? No Response from Projector ◆ Confirm that the projector is on ◆ Check the AC cord ◆ Check the control cable...

  • Page 3: Input Source Selection

    ON→PMM PMM→ON ON→OFF Failure OFF indicates standby mode, ON indicates that the projector is running, and PMM indicates power management mode. * "→" indicates the transition to another mode. 5. Input Source Selection 5.1 [Input Source Selection] Commands Commands for switching the input source, or for acquiring the input source selection value.

  • Page 4: Image Mode Selection

    6. Image Mode Selection 6.1 [Set Image Mode] Commands Commands for switching the image mode, or for acquiring the image mode setting value. Command Type Image mode STANDARD PRESENTATION SRGB MOVIE Get image mode 6.2 [Set Image Mode] Responses Responses to commands for setting the image mode, or for acquiring the image mode setting value. Response Type Image mode Success...
  • Page 5 8. Sharpness 8.1 [Set Sharpness] Commands Commands for setting the sharpness, or for acquiring the sharpness setting value. Command Type Sharpness Setting value Get sharpness Example: 8.2 [Set Sharpness] Responses Responses to commands for setting the sharpness, or for acquiring the sharpness setting value. Response Type Sharpness Success...

  • Page 6: Lamp Mode

    10. Aspect 10.1 [Aspect] Commands Commands for switching the aspect type, or for acquiring the aspect type value. Command Type Aspect Auto 16:9 Zoom Actual Get aspect value * Available settings vary depending on the input source and input signal format used. 10.2 [Aspect] Responses Responses to commands for setting the aspect type, or for acquiring the aspect type value.

  • Page 7: Blank Function

    12. Blank Function 12.1 [Blank Function] Commands Commands for executing the Blank function, or for acquiring the Blank function value. Command Type Blank Execute Cancel Get Blank 12.2 [Execute Blank] Responses Responses to commands for executing the Blank function, or for acquiring the Blank function value. Response Type Blank Success...

  • Page 8: Error List

    Wait until a response is received until sending commands. Send valid commands. Send commands in the valid format. Use the "POWER ON" command to turn the projector on. Wait until the power mode is ON,OFF, or PMM. Use the correct parameters.
  • Page 9 A communication protocol violation has occurred in e:E0XX COMMUNICATION_ERROR the projector. 65h 3Ah 45h 30h <numerical code> 20h 43h 4Fh 4Dh 4Dh 55h 4Eh 49h 43h 41h 54h 49h 4Fh 4Eh 5Fh 45h 52h 52h 4Fh 52h Cannot execute command under current screen e:1008 INVALID_SCREEN_ASPECT aspect setting.

This manual is also suitable for:

Sx80

Table of Contents