Arcoaire A Series Installation, Start-Up, Operating And Service And Maintenance Instructions page 13

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions
Wire Lead
Furnace
Color
Gray
Blue
1102420
Yellow
Orange
Red
Gray
Blue
1352420
Yellow
Orange
Red
Gray
Blue
1552420
Yellow
Orange
Red
1. A filter is required for each return-air inlet. Airflow performance included 3/4-in. (19 mm) washable filter (see accessory list). To determine airflow performance without this filter, assume an
additional 0.1 In. W.C. available external static pressure.
2. Adjust the blower speed tabs as necessary for the proper air temperature rise for each installation.
3. -- Indicates unstable operating conditions.
4. If the same motor speed tap is needed for heating and cooling, a Jumper Wire accessory kit is available. (See Specification sheet for the current Jumper Wire accessory part number). See
Function column for applicable limitations.
33 1/3
[845.9]
NOTES:
1. Two additional 7/8-in. (22 mm) diameter holes are located in the top plate.
2. Minimum return-air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer's recommendations for equivalent diameters.
a. For 800 CFM-16-in. (406 mm) round or 14 1/2 x 12-in. (368 x 305 mm) rectangle.
b. For 1200 CFM-20-in. (508 mm) round or 14 1/2 x 19 1/2-in. (368 x 495 mm) rectangle.
c. For 1600 CFM-22-in. (559 mm) round or 14 1/2 x 22 1/16-in. (368 x 560mm) rectangle.
d. For airflow requirements above 1800 CFM, see Air Delivery table in Specification Sheet literature for specific use of single side inlets. The use of both side inlets, a combination of 1
side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
Table 4 – Air Delivery - CFM (With Filter)* (Continued)
Function
Cooling. Do not use for heating.
Heating or alt Cooling
Alt Cooling or alt Heating
Alt Cooling. Do not use for heating.
Alt Cooling. Do not use for heating.
Cooling. Do not use for heating.
Heating or alt Cooling
Alt Cooling or alt Heating
Alt Cooling. Do not use for heating.
Alt Cooling. Do not use for heating.
Cooling. Do not use for heating.
Heating or alt Cooling
Alt Cooling or alt Heating
Alt Cooling. Do not use for heating.
Alt Cooling. Do not use for heating.
Fig. 17 – Dimensional Drawing
Test Airflow Delivery @ Various External Static Pressures
0.1 0.2 0.3 0.4
2250 2190 2130 2070
1995 1930 1865 1800
1540 1460 1385 1305
1345 1195 1135 1055
1335 1075 965 890
2065 2005 1940 1875
1825 1760 1695 1630
1760 1690 1625 1555
1620 1550 1480 1405
1325 1260 1185 1100
2205 2150 2090 2030
2055 1995 1935 1875
1860 1795 1730 1670
1495 1430 1355 1285
1295 1085 1000 910
13
0.5 0.6 0.7 0.8
2005 1950 1885 1820
1740 1670 1605 1535
1235 1165 1095 1035
980 920 845 770
820 735 660 580
1810 1740 1670 1600
1560 1490 1420 1350
1485 1415 1345 1275
1335 1260 1195 1130
1025 955 885 805
1965 1905 1840 1780
1810 1750 1690 1615
1605 1540 1470 1395
1210 1130 1065 995
835 765 670 600
0.9 1
1755 1685
1465 1400
955 890
695 620
505 440
1530 1470
1275 1205
1200 1130
1065 995
735 670
1710 1645
1540 1460
1320 1250
930 850
530 465
A190084