Littfinski Daten Technik RS-16-O-B Assembly Instruction

L D T
ittfinski aten echnik
Assembly Instruction
16-fold feedback module
from the Digital-Professional-Series !
RS-16-O-B
>> kit <<
As LR101 but with 16 inputs and additional optocoupling
for potential separation and for high interference safety.
Suitable for the RS-feedback bus
⇒ controls up to 16 feedback contacts
(safe galvanic separation by opto coupler).
⇒ separated by opto coupler
(contacts can be separated from layout ground
connection).
⇒ compatible to RS-feedback bus
(can be operated together with RS-8, LR101, LS100
etc.).
⇒ suitable for Lenz Digital plus System.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger of injuring due to sharp edges and tips! Please store this
instruction carefully.
Introduction:
You have purchased the 16 fold feedback module RS-16-O with
galvanic separation by opto coupler for your model railway. The
RS-16-O is a high quality product that is supplied within the
Digital-Professional-Series
We wish you having a good time using this product.
The feedback module RS-16-O can be easily operated on the
RS-feedback bus of your digital model rail way.
The RS-16-O is compatible to all digital model railways with RS-
feedback bus (e.g. Digital Plus from Lenz).
General:
Tools required for the assembly
Please assure that the following tools are available:
• a small side cutter
• a mini soldering iron with a small tip
• solder tin (if possible 0.5mm diameter)
Safety Instructions
• All electrical and electronic components included in this kit
shall be used on low voltage only by using a tested and
approved voltage transducer (transformer). All components
are sensitive to heat. During soldering the heat shall be applied
for a very short period only.
• The soldering iron develops a heat up to 400°C. Please keep
continual attention to this tool. Keep sufficient distance to
combustible material. Use a heat resistant pad for this work.
• This kit consist of small parts which can possibly be swallowed
from children. Children (especially under 3 years) shall not
participate on the assembly without supervision.
(LDT)
310201
Part-No.:
of Littfinski DatenTechnik (LDT).
Set-Up:
For the board assembly please follow exact the sequence of the
below assembly list. Cross each line off as done after
completing the insertion and the soldering of the respective part.
For the diodes please keep special attention to the correct
polarity (marked line for the cathode).
With reason to different makes of electrolytic capacitors you
will find different markings of the polarity. Some are marked with
"+" and some are marked with "-". Each capacitor has to be
assembled to the board that the marking on the capacitor is in
correspondence with the marking on the pc-board.
Integrated circuits (IC`s) are either marked with a half round
notch on one end or a printed point for the correct mounting
position. Push the IC`s into the correct socket or directly into the
pc-board (IC11) assuring that the notch or the printed point is
corresponding to the half-rounded marking on the pc-board.
Please attend to the sensitivity of the ICs to electrostatic
discharge, which will cause immediate damage of the IC. Before
touching those components please discharge yourself by
contacting an earthed metal (e.g. earthed radiator) or work with
an electrostatic safety pad.
Attend to the flat side of the transistors.
Resistor networks are marked at the one side with a printed
circle or a square for Pin 1.
Before assembling the unit clip the clamps together to a block
with the required connections.
The light emitting diodes have to be assembled with the longer
leg to be connected to "+" on the pc-board. Before soldering the
diodes push the distance spacer tubes on to the legs.
Assembly list
Pos. Qty. Component
1 1 Pc-board
2 2 Resistors 1,5KOhm
3 1 Resistor 220KOhm
4 2 Resistors 2,2KOhm
5 1 Resistor 220Ohm
6 1 Resistor 120Ohm
7 1 Resistor 33Ohm
8 2 Resistors 22KOhm
9 1 Resistor 3,3KOhm
10 1 Resistor 1MOhm
11 4 Networks 4*10kOhm
12 2 Networks 8*10kOhm
13 2 Diodes 1N4148
14 1 Diode 1N4003
15 2 Diodes BZX83 5V6
16 4 Capacitors 100nF
17 1 IC: LTV817
18 1 IC-socket 18poles
19 2 IC-sockets 16poles
20 4 IC-sockets 16poles
21 1 IC-socket 8poles
22 2 IC-sockets 6poles
23 1 Resonator 8MHz
24 1 Electrolytic capacitor 100uF/25V
25 1 Electrolytic capacitor 220uF/35V
26 1 Push button
27 4 Transistors BC 547
28 1 LED plus spacers
29 4 Clamps 2poles
30 5 Clamps 3poles
31 1 IC: Z86E0812PSC
32 2 IC: 4014
33 1 IC: 93C46
34 4 IC:LTV844
35 2 IC:CNY17III
36
Subject to technical changes and errors. © 07/2019 by LDT
Remarks Ref.
brown-green-black-brown R1, R2
red-red-black-orange R3
red-red-black-brown R4, R9
red-red-black-black R5
brown-red-black-black R6
orange-orange-black-gold R7
red-red-black-red R8, R10
orange-orange-black-brown R11
brown-black-black-yellow R12
attend to the polarity! RN1 ... 4
attend to the polarity! RN5 ... 6
attend to the polarity! D1, D5
attend to the polarity! D2
attend to the polarity! D3, D4
100nF = 104 C19...22
attend to the polarity! IC11
IC1
IC2, IC3
IC5 ... 8
IC4
IC9, 10
CR1
attend to the polarity! C18
attend to the polarity! C17
S1
attend to the polarity! T1 ... T4
attend to the polarity! LED1
build blocks before assembly
build blocks before assembly
attend to the polarity! IC1
attend to the polarity! IC2, 3
attend to the polarity! IC4
attend to the polarity! IC5 ... 8
attend to the polarity! IC9, 10
final control
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.ldt-infocenter.com
Done