Samsung LN19C450E1D Quick Setup Manual page 2

Step 5 :
Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the enTerE
To skip a screen, press the MenU button.
To turn on your TV, press the POwer button on the remote or press the
POwer button on the TV. To run Plug & Play, follow these steps:
Plug & Play
Select language of the OSD.
english
español
language : english
Français
U Move E enter
1. On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press enTerE button. The
Home Use screen appears.
2. Select Home Use, and then press enTerE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press enTerE button, the Antenna Source screen appears.
3. If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press enTerE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
4. If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital.
Remote Control Buttons and Functions:
Turns the TV on and off.
Press number buttons for direct access to channels.
Press to select additional digital channels broadcast by
the same station. For example, to select channel 54-3,
press 54, press -, and then press 3.
Adjust the volume.
Displays the channel list on the screen.
View the Media Play.
Quickly selects frequently used functions.
Use these buttons to select On Screen Menu items
and change menu settings.
Return to the previous menu.
Colored buttons for use in the Channel List, Media Play
menu, etc.
Use these buttons in the Media Play and Anynet+ modes.
( : Controls recording on Samsung recorders with the
Anynet+ feature)
After you have selected the cable system type, select Start, and then
press the enTerE button on your remote.
Most cable systems are Standard (STD) systems. If you are not sure
✎
about what kind of cable system you have, contact your cable company.
5. The TV memorizes the available channels. This process can take up
to 45 minutes. After the TV has memorized the channels, the Clock Mode
screen appears.
button.
6. Choose the Clock Mode. Select Auto if you have a digital channel in your
area. Select Manual if you don't, or if you have a cable or satellite box.
When done, press enTerE button. The Daylight Savings screen appears.
If you select Manual, the clock setting screen appears.
✎
7. Select the daylight saving time setting: Off, On, or Auto, and then press
enTerE button.
After the time zone screen, The connection method for best HD screen quality
8.
is displayed. Press Right arrow button on your remote to view each screen in
succession. Press the MenU button to skip this section.
9. The enjoy your TV screen appears.and then press
Basic Functions
Selecting a Source
To watch a movie on your Blu-ray player or watch your favorite TV show, you must
select the correct source. A source is a device, such as a Blu-ray/DVD player, a
cable/satellite box, antenna or a cable TV input.
Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In
connections.
To view the signal from a source connected to the
HDMI, DVI, Component, Composite, or D-sub jack, press the
your remote. Each time you press the SOUrCe button, you change to a different
source.
Press to switch between the sources (Blu-ray player,
cable box, DVD player, etc.) connected to your TV.
Return to the previous channel.
Cut off the sound temporarily.
Change channels.
Display the main on-screen menu.
MEDIA.P
Display Favorite Channel Lists on the screen.
Press to display information on the TV screen.
Exit the menu.
A B C D
S.MODE SLEEP MTS
S.MODe: Select the sound mode.
P.MODE P.SIZE CC
SleeP: Setting the Sleep Timer.
MTS: Press to choose stereo, mono or Separate
Audio Program (SAP broadcast).
P.MODe: Select picture mode.
P.SIze: Choose the picture size.
CC: Controls the caption decoder.
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.SIze
you press it, your TV displays the current setting. Thereafter, each time you press
the P.SIze button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen
enTerE button.
Wide Fit 4:3 Standard screen
Screen Fit displays a full HD picture covering the entire screen with no cutoff
✎
on any side. It is only available when your TV inputs an HDMI (720p, 1080i,
1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
Changing the Picture Mode
Your TV has three preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
The Picture Modes are listed and described in the table below:
SOUrCe button on
Mode
Brightens picture. For a vibrant, enhanced image in brightly lit or
Dynamic
sunny room.
Standard For a bright, detailed picture in a normally lit room.
Movie For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
1. With the TV on, press the TOOlS
The Tools menu appears.
2. Using the ▲ or ▼ on your remote, select Picture mode.
3. On the Picture Mode menu, use the ◄ or ► on your remote to select
MEDIA.P
the Picture Mode you want.
4. Press the exIT button to exit the menu.
Viewing the On Screen Menus
To view the On Screen Menus, follow these steps:
1. With the power on, press the MenU
on your remote. The main menu appears.
A B C D
The menu's left side has the following menu
options: Picture, Sound, Channel, Setup,
Input, Application, and Support.
2. Press the ▲ or ▼ button on your remote to
select a menu option, and then press the
3. When done using the menu, press the
English - 2
Changing Channels and Adjusting the Volume
Volume
button on your remote. The first time
MEDIA.P
Adjust the volume by pressing the
y button on the remote.
You can also change the
A
Zoom 1 Zoom 2
channels by pressing the
z buttons on
the front panel of your TV
and adjust the volume by
pressing the y
buttons.
Screen Fit
Setting the Clock
Before you can use your TV's On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1. Turn on your TV.
Using your remote, press the
2.
MenU button on your remote.
Then, select Setup → Time.
3. Select Clock Mode, and then
press the enTerE
Clock Mode to Manual.
Description
Select Auto if you have a
✎
digital channel in your area
and are not using a cable/sat
box.
4. Select Clock Set, and then press the
The Clock Set screen appears.
5. Using the number buttons on your remote, enter the month, day, year, hour,
and minute. Use the ◄ or ► button to move between entry fields.
button on your remote.
6. Press the reTUrn
Connecting a USB Device for Media Play
You can enjoy photo, music, and movie files
stored on a USB device by connecting it to the TV
and using the Media Play feature. To connect a
USB device for Media Play, follow these steps:
1. Turn on your TV.
Menu
Connect a USB device containing
2.
button
photo, music and/or movie files to
MEDIA.P
the USB jack on the rear of the TV.
3. When the Application selection
screen appears, press the
enTerE button on your remote
to select Media Play (USB).
enTerE button.
exIT button on your remote to exit.
A B C D
Channel
MEDIA.P
Change the channels by pressing
the z button on the remote.
If your TV is attached to a cable or
✎
satellite box, change the channel
using the box's remote.
B C D A B C D
Remote control sensor Power Indicator
Clock Set
Month Day Year
-- -- ----
Hour Minute am/pm
button. Set
-- -- --
U Move Adjust E enter R retour
U
enTerE button.
button on your remote when done.
TV Rear Panel
uSB Drive
Move enter return
L E R
Bn68-02606A-03