Download  Print this page

Samsung PN50C490B3D Quick Setup Manual

4+ series.
Hide thumbs
   

Advertisement

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the PDP TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
Screws (M4 X L10)
Guide Stand
1
Connect the Guide Stand to the
Stand
Stand using four screws (M4 X L10)
Rear
as shown.
2
3
With your TV upright, connect the
Fasten two screws (M4 X L12) at
TV to the Stand.
position 1, and then fasten two
screws (M4 X L12) at position 2.
Front
2
Rear
1
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
(Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using
HDMI for the highest picture quality.
When connecting to
AV IN
on the back of your TV, attach the video cable (yellow) to the green jack
next to the
AV IN
label. The jack will not match the color of the video cable (yellow).
Video Cable
(Not Supplied)
Top view
Front
Lowest Quality Connection
Audio/Video connection (480i only)
Rear
Using an Audio/Video Cable
Audio Cable
DVD, Blu-ray player, cable box, STB satellite
(Not Supplied)
receiver, VCR
Device
VIDEO OUT
AUDIO OUT
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control, select
Select Language of the OSD.
the language for the On Screen
Display (OSD), and then press
Language
the ENTERE button.
2
Select Home Use, and then
press the ENTERE button. If
Select 'Home Use' when installing this TV in your home.
you select Store Demo, the TV
will reset your picture and audio
Store Demo
settings every 30 minutes.
3
Select the Antenna source
to memorize, you must select
Select the Antenna source to memorize.
Antenna Source to same type
Air
as your cable system type. After
Cable
selecting source, select Start;
Auto
then press the ENTERE button
on your remote.
Best Connection
HD connection (up to 720p/1080i)
HDMI Cable (Not Supplied)
HDMI to DVI Cable
(Not Supplied)
Audio Cable (Not Supplied)
Good Connection
Component connection (up to 720p/1080i)
Component Cable
(Not Supplied)
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
POWER
The TV memorizes the available
channels. This process can take
P
Plug & Play
up to 45 minutes.
English
:
Español
Français
U Move E Enter
5
After the TV has memorized the
Plug & Play
channels, choose the Clock
Mode. Select Auto if you have
a digital channel in your area.
Select Manual if you don't, or
Home Use
if you have a cable or satellite
box. When done, press the
L Move E Enter
ENTERE button.
If you select Manual, the
Plug & Play
clock setting screen appears.
6
Select the daylight savings time
Start
setting: Off, On or Auto and then
Start
press the ENTERE button.
Start
This function is only available
U Move E Enter m Skip
when the Clock Mode is set to
Auto.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Using an HDMI Cable
DVD, Blu-ray player, HD cable box, HD STB
(Set-Top-Box) satellite receiver
HDMI OUT
Device
Very Good Connection
HD connection (up to 720p/1080i)
Using an HDMI to DVI Cable
Connecting a PC
DVI OUT
Connect your TV to a PC to use it as a Monitor.
AUDIO OUT
Device
Audio Cable (Not Supplied)
Using a Component Cable
HDMI to DVI Cable (Not Supplied)
DVD, Blu-ray player, cable box,
COMPONENT OUT
STB satellite receiver, VCR,
Device
AUDIO OUT
Audio Cable (Not Supplied)
7
Select the time zone in which you live, and then press the ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
Plug & Play
The Enjoy your TV. screen appears. Then press the ENTERE button.
Auto Program in Progress.
DTV Air : --
Air : --
If You Want to Rerun Plug & Play
DTV Cable : --
Cable : --
Cable : 35
1. Press the
SOURCE
48%
2. Press the
MENU
Stop
3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE
E Enter m Skip
button.
4. Press the ENTERE button again to select Plug & Play.
Plug & Play
Set the Clock Mode.
Auto
Clock Mode
Manual
U Move E Enter m Skip
Plug & Play
Set to daylight saving time.
Off
On
DST
Auto
U Move E Enter m Skip
Analog Audio connection
Using an Audio Cable
Amplifier / DVD home theater
Audio Cable (Not Supplied)
AUDIO IN
Digital Audio connection
Using an Optical Cable
Digital Audio System
Optical Cable (Not Supplied)
OPTICAL
HD connection
Using an HDMI to DVI Cable
AUDIO OUT
DVI OUT
Using a D-Sub Cable
D-Sub Cable (Not Supplied)
PC OUT
AUDIO OUT
button on your remote, then select TV mode.
button on your remote to display the menu.
BN68-03115A-01

Advertisement

Table of Contents

   Related Manuals for Samsung PN50C490B3D

   Summary of Contents for Samsung PN50C490B3D

  • Page 1: Quick Setup Guide

    Quick Setup Guide Step 4 Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.) 1-800-SAMSUNG (1-800-726-7864) STOP Use one of the connections below to connect your TV to an external A/V device. We recommend using Samsung Electronics America, Inc.
  • Page 2 SLEEP P.MODE P.SIZE Use these buttons in Media Play and Anynet+ modes (�: Controls recording for Samsung recorders that have the Anynet+ feature). Changing Channels and Adjusting the Volume Adjust the volume by pressing the Volume button ✎ You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.

This manual is also suitable for:

490

Comments to this Manuals

Symbols: 0
Latest comments: