Table of Contents
Advertisement
Quick Links
Nylon washer
(in between)
M3 Nut
7.5
190.5
Viewing window
for camera
Push here to
adust the
"L" bracket
camera's viewing
angle
I
n s t a l l a t I o n a n d
M3 Nut
Flat Washer
Note:
This camera bracket
has been adjusted
to look 90º RIGHT.
Note that the camera bracket axis
was moved to the LEFT Side of the "L" bracket.
Original Location
of Axis
Camera Bracket
Pen Stud
for Side-mounted
Camera
Pen Stud for
Front-mounted
Camera
Counter Sinks
w w w
H
Camera Bracket
Axis (pem stud)
12
304.8
Viewing window
for camera
o
p e r a t I n g
.
l I n e a r c o r p
s
eIgHt
trIp
34
863.6
I
n s t r u c t I o n s
.
c o m
c
amera
6
152.4
Hc s
erIes
12
304.
Advertisement
Table of Contents
Related Manuals for Linear aigis mechtronics HC Series
Summary of Contents for Linear aigis mechtronics HC Series
- Page 1 M3 Nut Flat Washer Nylon washer (in between) p Down Camera Bracket eIgHt trIp amera Axis (pem stud) Flat Washer M3 Nut Note: 40.6 This camera bracket has been adjusted to look 90º RIGHT. Note that the camera bracket axis 304.8 was moved to the LEFT Side of the “L”...
-
Page 2: Important Safeguards
IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions 12. Power Lines - An outdoor system should not be located in should be read before the unit is operated. the vicinity of overhead power lines or other electric light 2. -
Page 3: Safety Precautions
Safety PrecautionS UNPACKING Unpack carefully. This is electromechanical equipment and should be handled with care. Check for the following items: • Verify the unit model number. caution: to reDuce tHe riSK • Verify that parts listed below have been included. of eLectric SHocK, Do not reMoVe coVer (or BacK). -
Page 4: Care And Maintenance
SERVICE DESCRIPTION If the unit ever needs repair service, the customer should The HC Series of Height Strip camera housings are intended contact Aigis Mechtronics for return authorization and to improve in-store security in two ways. First, when shipping instructions. installed next to the main entrance of a store, cameras within the store will capture a subject’s height when exiting as he or she passes the brightly colored labels. -
Page 5: Cover Removal
VOlTAGE & MAx WATTAGE 6.2 camera removal/relocation, and installing accessory camera Color Camera 95mA (Max) @ 12VDC 1. Each Height Strip ships from the factory with a single Warning: All cameras are powered by DC voltage. camera installed that looks through the viewing window If you are running DC voltage over a pair of wires, located at the 5-1/2 foot mark. -
Page 6: Installation
INSTAllATION 7.1 Side-mounted cameras note: If NOT using the side-mounted camera feature of the 7. Fit the cover back over the base and tighten down the Height Strip, proceed to the next applicable section. four (4) M3 screws to secure. 1. - Page 7 7.2 installing the unit onto a Mullion or Metal Doorframe 1. Measure from the floor to the 5-foot mark on the mount- 11. At the desired through-hole location(s), drill a hole in the ing surface. Make a mark at 5 feet. mullion wide enough to accept the customer-provided power and video cables.
- Page 8 7.3 installing the unit onto a Solid Wall 7.4 installing the unit using the accessory Wall Bracket (Mt-Hc) 1. Refer to steps 1 to 6 above. Replace fasteners and wall note: cable entry can only be accomplished via the anchors from the hardware kit with customer-supplied knockouts at the top or bottom of the Height Strip components as desired.
- Page 9 Notches designate 5-foot mark. The mounting holes in the Height Strip base are not symmetrical. Take care to select the correct hole for your particular application. figure 9 15. Terminate the ends of the customer-supplied cables as 8. Remove the cover from the Height Strip by removing the required, and connect power and video cables to the four (4) cross-recessed screws.
-
Page 10: Dimensional Outlines
DIMENSIONAl OUTlINES Back View (ø.19 X3) MOUNTING HOLES Back View 14.7 374.7 247.7 Side View Top Down Bottom Up 43.2 40.6 304.8 304.8 190.5 63.5 Viewing window Viewing window Viewing window for camera for camera for camera 152.4 76.2 863.6... - Page 12 Now Part of 100 0266 002 AIG 02/12 1950 Camino Vida Roble, Suite 150 Carlsbad, CA 92008 Data subject to change without notice. Tel: 760.438.7000 800.421.1587 www.aigismech.com • www.linearcorp.com Copyright © 2012 Linear LLC...