Advertisement
Installation
Before the installation, make sure the peripherals of all PCs are
grounded properly and turned off.
1. Connect the monitor, keyboard and mouse with the Console
Port Connectors.
2. Use the recommended extension cables to connect the
PCs with the CPU Ports of KVM Switch.
3. Turn on the PCs.
Operation
1. The function of LED display:
LED DISPLAY
DESCRIPTION
Light off
PC power off
Green light on
PC power on and connected
Green light on & Red light
PC power on, connected and
flashing
selected
Note: It occurs occasionally that the green light of LED display is
on and the red light of LED display keeps flashing after
shutting down the PC because of the PC default. The
condition will not affect the regular operation of KVM
switch.
2. 2 ways for PC selection – Push-button switch or hot key
2-1 Push-button switch (Manual Type)
Press the button on front panel to switch the CPU ports.
The red light of LED indicates which PC is selected.
2-2 Hot Key option
Hot Key Navigation allows you to select PC from the
keyboard directly.
Options for Hot Key Navigation:
§ Select PC by Hot Key
§ Command mode
§ Auto scan mode
§ Beep sound on/off option: Press [Right Shift] key
twice to turn on or off the beep sound when needed.
§ Select PC by Hot Key:
Press either left or right [Ctrl] key twice.
Item
Hot Key Operation
[L Ctrl] + [L Ctrl] or
IC-612-I
Access between two PCs.
[R Ctrl] + [R Ctrl]
IC-614-I
[L Ctrl] + [L Ctrl]
Switch to the previous PC.
IC-614-I
[R Ctrl] + [R Ctrl]
Switch to the next PC.
§ Command Mode:
Press [Num Lock] key twice, and the 3 keys [Num
Lock], [Caps Lock] and [Scroll Lock] will flash to
access the Command Mode.
a). Directly press the function key [F1] ~ [F2] for IC-612-I or
[F1] ~ [F4] for IC-614-I to select PC.
b). Press [Left Ctrl] key to disable [Ctrl] and [Shift] hot key
function.
-3-
c). Press [Right Ctrl] key to enable [Ctrl] and [Shift] hot key
function.
d). Press [Left Shift] key to turn off the beep sound.
e). Press [Right Shift] key to turn on the beep s ound.
f). Press [Left Alt] key to disable Auto skip function.
g). Press [Right Alt] key to enable Auto skip function.
h). Press [Esc] or [Enter] key to quit the mode.
Note: [Ctrl] Hot Key function – Selecting PC ports.
[Shift] Hot Key function – Beep sound on/off.
§ Auto Scan Mode:
Press [Scroll Lock] key twice to activate the Auto Scan Mode.
The time scale of Auto Scan ranges from 5 to 30 seconds,
and it can be recognized by the lights of the 3 keys
Lock], [Caps Lock] and [Scroll Lock]
below.
a). Press the right number key [+] to increase time scale.
b). Press the right number key [-] to decrease time scale.
c). Press [Esc] key to quit the mode.
Note: Light(s) corresponding timetable
Seconds
Num Lock
5 seconds
10 seconds
15 seconds
20 seconds
25 seconds
30 seconds
3. The boot-up default of Smart View KVM Switch is
connected to your first activated PC.
4. When the PC is shut down under the function of "Auto
skips over the power-off PC", it cannot be turned on again
by keyboard.
Troubleshooting
Make sure the cables are qualified and positioned.
Q1 :
The keyboard does not respond accurately.
Function
A1a:
Re-install the keyboard. Unplug the keyboard from the
Console Port and plug it back again.
A1b:
Re-install the Smart View KVM Switch. Shut down the
PCs, unplug the cables from the Smart View KVM
Switch and wait for five seconds. Then plug the cables
back and activate the PCs.
A1c:
When under Auto Scan Mode, please press [Esc] key
to escape.
A1d:
Try another keyboard.
Q2 :
The mouse does not respond accurately.
A2a:
Re-install the mouse. Unplug the mouse from the
Console Port and plug it back again.
[Num
as the timetable
Caps Lock
Scroll Lock
Off
Off
On
On
Off
Off
On
Off
On
Off
On
Off
Off
On
On
On
On
Off
-4-
A2b:
Re-install the Smart View KVM Switch. Shut down
the PCs, unplug the cables from the Smart View
KVM Switch, and wait for five seconds. Then plug
the cables back and activate the PCs.
A2c:
Make sure the mouse is set on PS/2 mode.
A2d:
Try another mouse.
Note: If you are using a particular mouse, we suggest
installing the mouse driver from original manufacturer
to reveal the functionality of Smart View KVM Switch.
Q3:
The mouse is out of control.
A3:
The characteristic of the mouse is inefficient. Try
another superior mouse and plug it back again. Start
the operation after hearing the beep sound.
Q4:
There is the video problem.
A4a:
The setting of resolution or bandwidth is over high.
Smart View KVM Switch supports the VGA, SVGA,
Multisync and XGA (interlaced) with the resolution up
to 1920 x 1440 Hz. The maximum bandwidth is 200
MHz.
A4b:
The cable is unqualified. Please use the superior
cables of Smart View cables series.
Q5:
Why the green light of LED display is on and red
light keeps flashing after shutting down the PC?
A5:
The condition is normal and caused from the PC
default. The condition will not affect the regular
operation of Smart View KVM switch.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or
registered trademarks belonging to their respective
companies.
-5-
Advertisement
