Table of Contents
Advertisement
Care and cleaning
Installation
Only when switched off!
Heat exchanger
– Scope of delivery: dryer, operating and installation instructions, basket for woollens
The dryer's heat exchanger is cleaned automatically during drying.
SELF CLEANING
appears
(depending on the model).
rolling in the display panel. Do not pull out the condensate container during the cleaning
– Check the dryer for transport damage.
process.
– The dryer is very heavy. Do not attempt to lift it on your own.
Dryer housing, control panel
– Be careful to avoid sharp edges.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
– Wipe with a soft, damp cloth.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
– Do not clean with a water jet.
– Remove detergent and cleaning agent residue immediately.
– If in doubt, have the appliance connected by a specialist.
– Some water may collect between the window and the seal during drying.
Setting up the dryer
1.
This does not affect the proper operation of your dryer in any way.
– The mains plug must always be accessible.
Filter in the condensate container
– Ensure that the appliance is placed on a clean, level
and firm surface.
The filter is cleaned automatically when the condensate container is emptied.
However, the filter should still be cleaned regularly under running water
This prevents
– Do not obstruct the air inlet on the dryer.
stubborn deposits/dirt from building up.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet
1. Pull out the condensate container.
and a spirit level.
Never remove the threaded feet!
Do not install the dryer behind a door
or sliding door which could prevent or
obstruct the dryer door from opening.
2. Pull the filter out of its snap-in lock.
This will prevent children from locking
themselves in and risking their lives.
3. Clean the filter under running water or in the dishwasher.
2.
For mains connection,
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (
same.
– The connected load and necessary fuse protection are specified on the rating plate.
Frost protection
4. Refit the filter.
5. Insert the condensate container so that it locks into place.
Preparation
1. Empty the condensate container
Only operate the dryer with the filter inserted.
2. Select any programme using the programme selector.
3. Press the Inicio/Stop (Start/Pause) button
4. Wait several minutes or until the dryer stops, and then empty the condensate container
Moisture sensors
again.
5 Turn the programme selector to Stop.
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure the moisture level of the laundry.
Transport
After sustained, repeated operation, a fine layer of limescale
may form on the moisture sensors.
1. Open the door.
– Prepare the dryer
see Frost protection.
– Transport the dryer in a vertical upright position.
2. Clean the moisture sensors with a damp sponge which has a rough
surface.
– Following transportation, do not use the dryer for two hours.
Do not use steel wool or abrasive agents!
The dryer contains residual water; this can flow out if the dryer is tilted.
8
Technical Data
Dimensions (DxWxH)
60 x 60 x 85 cm (height adjustable)
Weight
approx. 51 kg
Max. capacity
8 kg
Condensate container
4.0 l
Connection voltage
220-240 V
Connected load
1000 W
Fuse protection
10 A
Ambient temperature
5 - 35°C
Take all accessory parts out
Product number
Inside of door
of the drum.
Production number
The drum must be empty.
The rating plate can be found on the back of the dryer.
Power consumption when switched off
0.10 W
Power consumption when ready for use (left-on mode)
1.00 W
Drum interior light (depending on model): The drum lights up after the door is opened and after the programme starts, and switches off
automatically.
Consumption values table
Spin speed which is used for
Programme
Duration**
spinning the laundry
Cottons
8 kg
4 kg
Cupboard dry*
1400 rpm
179 min
111 min
1000 rpm
203 min
122 min
800 rpm
227 min
143 min
Clean and level
Iron dry*
1400 rpm
125 min
75 min
1000 rpm
150 min
90 min
Make sure that the air inlet
800 rpm
176 min
106 min
remains unobstructed
Synthetics
3.5 kg
see Safety instructions
page 13.
Cupboard dry*
800 rpm
55 min
600 rpm
71 min
page 10) must be the
*
Programme setting for testing in accordance with the applicable EN61121 standard.
** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric,
the degree of dryness that has been set and the amount of laundry being loaded.
Do not operate the dryer if
Most efficient programme for cotton fabrics
there is a risk of frost.
The following "standard cottons programme" (identified with
) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
page 4,8/12.
Standard programme for cottons in accordance with current EU regulation 932/2012
Programme
Load
Energy consumption
condensation is pumped into the container.
Cottons Cupboard dry
8 kg/4 kg
1.80 kWh/1.04 kWh
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
Optional accessories
(order from the after-sales service using the order number, depending on the model)
WTZ
Washer-dryer stack connection set
20410
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer must be fastened
to the washing machine using this connection set. WTZ 11400: with pull-out worktop.
Platform
WTZ
20500
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Wollens basket
WTZ
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for "Woollens basket").
20600
9
Normal noises
What to do if ...
During drying, the compressor and the pump generate some noise which is entirely normal.
The compressor in the dryer may occasionally generate a humming
noise. The volume and pitch of this may vary
depending on the selected
programmes and the progress of the drying.
The compressor in the dryer is ventilated from time to time, which
creates a whirring sound.
The automatic cleaning process causes
Energy consumption**
a clicking noise.
8 kg
4 kg
1.57kWh
0.93 kWh
1.80 kWh
1.04 kWh
2.04 kWh
1.25 kWh
1.10 kWh
0.66 kWh
The process of pumping the condensation into the condensate con-
1.36 kWh
0.82 kWh
tainer generates pumping noises.
1.64 kWh
0.98 kWh
3.5 kg
0.51 kWh
What to do if ...
0.66 kWh
Turn the programme selector to Stop
and remove the mains plug from the socket.
The Inicio/Stop (start/pause) indicator light does
Mains plug plugged in?
not light up.
Programme selected?
Check the socket fuse.
The display panel light and indicator lights
Energy-saving mode is activated
see the separate Energy-saving
(depending on model) go out and the Inicio/Stop
mode instructions.
(start/pause) indicator light flashes.
The display panel switches off.
The appliance goes into the sleep mode after activating
Terminado en/em (Finished in) option
page 5.
Programme duration
The
(Condensate container) indicator light
Empty the condensate container
page 4.
203 min/122 min
flashes.
Press the Inicio/Stop (start/pause) button to reset the displayed
indication and then press the Inicio/Stop (start/pause) button
again to restart the appliance if necessary.
Is the condensation drain installed?
Condensation drain hose
blocked
check and clean the hose. Stopper in the condensate
container?
separate Instructions for condensation drain.
Is the filter in the condensate container dirty?
Clean the filter in
the condensate container
Care and cleaning, Page 8.
Residual water in the condensate container
Not a fault. If the condensation drain is installed, residual water
despite the dryer being connected to
remains in the condensate container due to the dryer's self-cleaning
the condensation drain.
function.
10
11
After-sales service
Turn the programme selector to Stop
and remove the mains plug from the socket.
If you cannot rectify the fault yourself (e.g. switching off/on)
(Fluff filter) indicator light
Clean the fluff filter
page 4/8.
flashes.
Press the Inicio/Stop (Start/Pause) button to reset the displayed indication and
always find an appropriate solution and avoid unnecessary visits by engineers.
then press the Inicio/Stop (Start/Pause) button again to restart the appliance if
The contact details of your local after-sales service can be found in the enclosed after-sales service directory.
necessary.
Please provide the after-sales service the product number (E no.) and the production number (FD) of the appliance.
– GB 03 448 928 979 (Calls charged at local or mobile rate.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
SELF CLEANING
appears in
Not an error. Automatic cleaning of the heat exchanger.
the display panel.
Do not empty the condensate container.
Dryer does not start.
Inicio/Stop (Start/Pause) button selected?
Door closed? Programme set?
Product number
Production number
Programme terminates shortly after
Ambient temperature greater than 5°C?
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest assured that the repair will be carried out by
trained service technicians using original spare parts.
starting.
Is the appliance loaded with the laundry?
Load too small for selected programme?/Use timed programme
page 6/7.
Safety instructions
Loaded laundry dry?
Water is leaking out.
Make sure the dryer is level.
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use
– in rooms inside the house.
The door opens by itself.
Push the door closed until you hear it engage.
the dryer...
– to dry fabrics.
The dryer must
– be used for purposes other than those described above.
Creasing.
Laundry load exceeded?
NEVER...
– be modified in terms of its technology or properties.
Remove articles of clothing immediately after the end of the programme, hang
up and pull into shape.
Hazards
– The dryer must not be used by children or persons who have not been instructed in its use.
– Do not leave children unsupervised near the dryer.
Unsuitable programme selected
page 7.
– Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular
Laundry is not dried correctly or is
After the end of the programme, warm laundry feels damper than it actually is.
– Do not lean or sit on the door
still too damp.
Spread the laundry out and allow the heat to disperse.
Installation
– Secure loose cables
Risk of tripping.
Finely adjust the dryness level – this extends the drying time but does not
– Do not operate a dryer if there is a risk of frost.
increase the temperature. Your laundry will become drier.
Mains connection – Connect the dryer to an AC earthed socket according to specifications, otherwise it cannot be guaranteed that
the appliance is completely safe.
Select a programme with a longer drying time or increase the drying level.
– The cable cross-section must be sufficient.
This does not increase the temperature.
– Only use earth-leakage circuit breakers with the following symbol:
Select a time programme for extended drying of laundry that is still damp.
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
If you have exceeded the maximum load for the programme, the laundry may
– Do not touch or hold the appliance plug with wet hands
not be dried correctly.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead
Clean the moisture sensor in the drum. A fine layer of limescale may adversely
Operation
– Only load the drum with laundry. Check the contents before you switch the dryer on.
affect the performance of the sensors and your washing will not dry properly.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair styling
Drying has been interrupted as a result of a power cut, because the condensate
products, nail varnish remover, stain remover, cleaning solvent, etc.)
– The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
container is full or because the maximum drying time has been exceeded.
– Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer
– Do not turn off the dryer until the drying process ends, unless the laundry will be removed quickly and spread out, so
Drying time too long.
Clean the fluff filters under running water
page 4/8.
that the heat can dissipate.
Insufficient supply of air
Ensure that air can circulate.
– Do not put laundry containing foamed material/rubber in the dryer
the dryer be damaged due to possible deformation of the foamed material.
Air inlet possibly blocked
Clear inlet
page 9.
– When cleaning the fluff filter, make sure that no foreign material (down or filling material) gets into the air duct
opening. If necessary, clean the drum beforehand with a vacuum cleaner. If foreign material should still get into
Ambient temperature higher than 35°C
Ventilate the room.
the air duct
call the after-sales service
– Light things, such as long hair, may be sucked into the air inlet of the dryer
One or more indicator lights are
Clean the fluff filter
page 4,8/12.
– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure that the items are left at a
flashing.
Check the installation conditions
page 9.
temperature that ensures that the items will not be damaged.
Switch off, allow to cool, switch back on and restart the programme.
– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated with fluff.
Power failure.
Remove the laundry from the dryer immediately and spread out. This allows the
Defect
– Do not use the dryer if it is defective or if you suspect that it is. Repairs must only be carried out by the after-sales
heat to dissipate. Be careful as the door, the drum and the laundry may be hot.
service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only have the defective mains cable replaced
Other intermittent noises
Not an error. Normal noises
page 11.
by the after-sales service.
and vibrations.
Spare parts
– For safety reasons, you must only use genuine spare parts and accessories.
Loud humming noise for several
Has the condensate container been properly inserted?
Push the condensate
Disposal
– Pull out the appliance plug, then cut off the mains cable from the appliance. Dispose of the appliance at a municipal
seconds.
container all the way in.
waste disposal facility.
Not an error. Normal noises
page 11.
– The dryer's heat exchanger contains fluorinated greenhouse gas (R134a) in a hermetically sealed unit
of in a proper manner. Capacity: 220 g.
– Packaging: Keep all packaging out of reach of babies and children
– All materials are environmentally sound and can be reused. Dispose of them in an environmentally-responsible
manner.
12
What to do if..., page 12, please contact our after-sales service. We will
You can find this information: inside the door* / in the opened service
flap* and on the rear of the appliance.
*depending on the model
Risk of explosion.
Risk of tipping.
Risk of electric shock.
Risk of electric shock.
Risk of fire/explosion.
Risk of explosion.
elastic material may be destroyed and
Dryer
Risk of fire/explosion.
WTW83230EE
Risk of injury.
en operating instructions
dispose
Risk of suffocation.
13
Advertisement
Table of Contents
