Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG DI9814
Summary of Contents for AEG DI9814
- Page 1 DI 9814 User manual Cooker Hood...
-
Page 2: Table Of Contents
Contents Safety warnings ................3 Description of the Appliance ............5 Extraction mode ................. 5 Recirculation mode ................5 Control Panel ..................6 Maintenance and Care ..............8 Metal grease filter ................8 Charcoal filter ..................9 Warning .................... 10 Changing the light bulbs .............. -
Page 3: Safety Warnings
Safety warnings • When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/ 125 mm reduction flange provided. - Page 4 provided by the competent authorities. • The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH, it is in any event necessary to proceed in accordance with the maintenance instructions provided in this manual).. •...
-
Page 5: Description Of The Appliance
Description of the Appliance • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • The hood is supplied as an extractor unit and can also be used with a recirculation mode by fitting a charcoal filter. Extraction mode •... -
Page 6: Control Panel
Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. - Page 7 Grease and charcoal filter maintenance indicator This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled.
-
Page 8: Maintenance And Care
Maintenance and Care Warning! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Metal grease filter •... -
Page 9: Charcoal Filter
Charcoal filter • The charcoal filter should only be used if you want to use the hood in recirculation mode. • Replacing the charcoal filter The charcoal filter cannot be washed nor regenerated. The charcoal filter should be replaced every 4 months under normal use. -
Page 10: Warning
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. -
Page 11: Special Accessories
Special accessories Charcoal filter TYPE 15 Technical assistance service You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. For service in Australia call 1300 650 020. When calling, please be ready to specify: The model code number The serial number... -
Page 12: Electrical Connection
Electrical connection Safety warnings for the electrician Safety warnings for the electrician The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. -
Page 13: Installation
Installation - Fig. 6-7-8-9 Assembling the deflector (3 parts – only for filter version): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. Fig. 6. Expansion plugs are provided to secure the hood to most types of ceilings. - Page 14 • Adjust extension of the hood support structure, as the final height of the hood depends on this, and remember that with installation completed the hood must be at least 60 cm above the hob top for electric cookers and 75 cm for gas or mixed fuel cookers. •...
- Page 15 14,5 10 10 Fig. 7...
- Page 16 • For extractor versions (13A), connect the other end of the exhaust pipe to the flue. For filter versions (13F), fit deflector F to the support and secure it to the bracket supplied using 4 screws, then connect the exhaust pipe to the connection ring located on the deflector.
- Page 17 • Carry out electrical connection of control panel and bulbs (17). • Join the two bottom sections of the flue covering the support (18) using 6 screws and springs (3 each side, see the plan diagram for joining the two sections - springs must be fixed horizontally). •...