Yamaha M3000-24 Owner's Manual page 7

I M1–M8 switches
These switch on/off the signal which is sent from the
input channel to MIX buses 1–8.
Note: If these switches are off, no signal will be sent
to the corresponding MIX bus from this input
channel, regardless of the switch setting of the vari-
able/fixed select section (page 13).
J M1–M8 mix level controls
These controls send the signal from the input channel
to MIX buses 1–8. When the control is in the " "
position, the level is nominal (0 dB). Use the PRE
switch ( P ) to switch between pre/post fader.
Note: For MIX bus pairs for which the variable/fix
select section (page 13) switch is set to FIX, the out-
put level which is sent from each input channel to
the bus will be fixed, and therefore the mix level
control setting will have no effect.
K M9–M12 switches
These are on/off switches for the signals that are sent
from the input channel to MIX buses 9–12.
L M9–M12 mix level controls
These controls send the signal from the input channel
to MIX buses 9–12. When the control is in the " "
position, the level is nominal (0 dB). Use the PRE
switch ( P ) to switch between pre/post fader.
+48V PHANTOM
MASTER
Input
HA
PAD
1-24/1-40
GAIN
26dB
+48V
INSERT I/O
HPF 4 Stage EQ
HPF
1
2
from VCA Master
7
8
CHECK ON
from Ctrl Master CONTROL
ON/EDIT
M M13/M14 , M15/M16 switches
These are on/off switches for the signals that are sent
from the input channel to MIX buses 13–16. M13 and
14, and M15 and M16 are stereo pairs, and each pair is
turned on/off by one switch. Use the PRE switch ( P )
to switch between pre/post fader.
N M13/M14 , M15/M16 mix level controls
These controls send the signal from the input channel
to MIX buses 13–16. When the control is in the " "
position, the level is nominal (0 dB). M13 and M14,
and M15 and M16 are stereo pairs, and the output
level of each pair is controlled by one knob. Use the
PRE switch ( P ) to switch between pre/post fader.
O M13/M14 , M15/M16 pan controls
These controls set the panning of the signals that are
sent from the input channel to MIX buses 13/14 or
MIX buses 15/16. When the control is in the center
position, an equal amount of signal will be sent to
both buses.
P PRE switches
These are pre-fader/post-fader switches for the signals
that are sent from the input channel to MIX buses 1–
16. Pre/post can be switched independently for each
group of MIX buses: 1–4, 5–8, 9–12, and 13–16. When
the switch is pressed (
nal will be sent to the corresponding group of MIX
buses.
Internal Jumper
PEAK
NOM
SIGNAL
VCA
EQ
), the post-EG/pre-fader sig-
MIX
DIRECT OUT (VARIABLE)
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
ST PAN
M1
M2
PRE
M3
M4
M5
M6
PRE
M7
M8
M9
M10
M11
PRE
M12
M13/
PAN
M14
PRE
M15/
PAN
M16
PFL
Control panel
MIX
(FIX)
PFL ST
1 2 3 4 5 6 7 8 L R ON L R
7