Subscribe to Our Youtube Channel
Related Manuals for Landi E830RFWD
Summary of Contents for Landi E830RFWD
- Page 1 Model：E830 Countertop POS This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. ...
-
Page 2: Table Of Contents
MATTERS NEED ATTENTION ........................17 8 TRANSPORTATION AND STORAGE......................17 9 CUSTOMER SERVICE CENTER ........................17 ......................... 17 OTE ABOUT FTER SALES ERVICE ............................18 RODUCT AINTENANCE ................................... 18 ONTACT This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 2 / 18 ... -
Page 3: Disclaimer
LANDI’s prior written consent. Fujian LANDI reserves the right to claim compensation on all direct or indirect loss incurred by the above illegal action. Fujian LANDI shall not be liable for any damages, failures and data loss to device or accessories resulting from improper operation not in accordance with the guidance of this manual. -
Page 4: Standard Compliance
In no event shall LANDI be liable for any data or revenue loss, or consequential, indirect, punitive, special or incidental damages resulting from any reasons. -
Page 5: Acronym Definitions
In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment Waste, which can have an effect on the environment and human health. Acronym Definitions Acronym Definitions Alternating Current Bluetooth Direct Current This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 5 / 18 ... -
Page 6: Product Introduction
Save the shipping carton and packing material for future repacking or terminal movement. ***************************************************************************************** WARNING E830 is a device with security characteristic. Any disassembly will probably make it work abnormally. ***************************************************************************************** 1.2 Appearance and Interface 1.2.1 Appearance This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 6 / 18 ... -
Page 7: Interfaces
1, Telephone line cord port 2, Extension telephone line port 3, Power socket 4, COM2 port 5, Drawer type SAM card connector 6, COM1 port 7, USB host expansion port 8, Ethernet RJ45 Port This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 7 / 18 ... -
Page 8: Product Technical Characteristics
EPT-DEV for WINDOWS; Support ANSI C language Power adapter：AC 100V～240V 50～60Hz/0.3A Power Supply Output：9V/1A Working temperature: -30℃～50℃ Environmental Storage temperature:: -20℃～70℃ Characteristics Relative humidity: 5%～90℅, Non-condensing 188mm L×82mm W×65mm H Dimension & Weight 340g This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 8 / 18 ... -
Page 9: Product Function And Configuration
2.2 Product Function and Configuration E830 is a Point of Sales (POS) product developed based on the 3rd Gen, payment kernel of LANDI. It is configured with ARM Cortex-A9 Core Security Processor to provide powerful processing capabilities and security features; and its 2.8”LCD delivers excellent customer experience. -
Page 10: Telephone Line Cord Port
PINPAD send receive Single GND Single GND 2.3.6 USB host expansion port Terminal has a USB expansion port to connect a USB device which is recommended to use S160 PINPAD. USB HOST This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 10 / 18 ... -
Page 11: Product Installation Guide
Press the top of the SAM cards and pull it out slowly. ****************************************************************************************** NOTE When using only one SAM card, it is recommended to insert SAM1 slot (bottom). ****************************************************************************************** 3.2 SIM Card Installation Same procedures as above Chapter 3.1 This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 11 / 18 ... -
Page 12: Microsd Card Installation
Place the paper roll onto paper box and pull out the paper over the ripper. Close the printer cover. Please be noted that the carbon layer side of the printer paper should be faced against the the cover. Leave a section of paper out after closing the cover. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 12 / 18 ... -
Page 13: Product Instructions
4.2 Power on/off Operation Normal power on: Press <Power> button for about 1s until the terminal displays the figure below: Normal power off: Press <Power> button for 2s until the terminal displays the figure below: This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 13 / 18 ... -
Page 14: Magnetic Card Reader
The IC card should be horizontally inserted into the card reader with chip side upwards. Make sure the card is completely inside the card reader and prevent the card chip contacts from being damaged or oxidized, otherwise it may cause transaction failure. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 14 / 18 ... -
Page 15: Rf Card
If you need to adjust the typing paper distance, please power off the terminal, and then replace the paper roll with correct operation. Dust or wastepaper remnant in the printer will reduce the efficiency. Please use soft brush to clean it. (Be careful not to scratch the print head). This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 15 / 18 ... -
Page 16: Notes Of Wireless Communication
A: The device might be under low energy status or the program may be damaged. Please make sure the power is enough and then restart your device. If it still fails, please contact our customer service department for help. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. ... -
Page 17: Matters Need Attention
Note about After-sales Service Before asking for customer service, please be noted to back up the data in the terminal. We are not responsible for backing up the data received from our customer service. This document is the property of LANDI. Its content cannot be reproduced or divulged without the company’s written approval. 17 / 18 ... -
Page 18: Ontact
For details, please see the warranty manual. Contact Fujian LANDI Commercial Equipment Co., Ltd Add: No.68 Hongshanyuan Road, Gulou district, Fuzhou. Mailing Add: Building 23, the 1st Section, Software Garden, No.89 Software Road, Fuzhou, Fujian, China...
Need help?
Do you have a question about the E830RFWD and is the answer not in the manual?
Questions and answers