Subscribe to Our Youtube Channel
Related Manuals for Lanpro LP-SG2401
Summary of Contents for Lanpro LP-SG2401
- Page 1 LP-SG2401 10/100/1000Mbps 24 Port GigaSpeed Switch www.lanpro.com User Guide LPSG2401_UG_ENB01W...
- Page 2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. LanPro is a registered trademark of LanPro Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from LanPro Inc.
-
Page 3: Table Of Contents
CONTENTS Package Contents ..............Chapter 1 Product Introduction........1.1 Product Overview ..........1.2 Features ............1.3 IEEE 802.1p QoS ..........Chapter 2 Identifying External Components ....2.1 Front Panel ............2.2 Rear Panel ............Chapter 3 Installation ............. 3.1 Precautions ............. 3.2 Installation ............ -
Page 4: Package Contents
Mounting screws and two “L” brackets. Make sure that the package contains the above items. If any of Note: the listed items are damaged or missing, please contact the retailer from whom you purchased the LP-SG2401 24-port Gigabit Ethernet Switch for assistance. -
Page 5: Chapter 1 Product Introduction
Chapter 1: Product Introduction This chapter describes the features of the LanPro model LP-SG2401 24- port Gigabit Ethernet Switch. 1.1 Product Overview The LP-SG2401 24-port Gigabit Ethernet Switch provides 24 10/100/1000Mbps Auto-Negotiation RJ45 ports. Each port of LP-SG2401 supports auto MDI/MDI-X fuction, eliminating the need for crossover cables or Uplink ports. -
Page 6: Ieee 802.1P Qos
1.3 IEEE 802.1p QoS The LP-SG2401 Switch supports 802.1p priority queuing Quality of Service (QoS), which is an implementation of the IEEE 802.1p standard. With 802.1p QoS function, you can reserve bandwidth for important functions that require a large bandwidth or have a high priority, such as VoIP (Voice- over Internet Protocol), web browsing applications or video conferencing. -
Page 7: Chapter 2 Identifying External Components
1000Mbps speed. If the LED is off, it is working on 10/100Mbps speed or no device is connected. 2.2 Rear Panel The rear panel of LP-SG2401 features a power socket and a Grounding Terminal (markerd with Figure 3. Switch Rear Panel Sketch ... -
Page 8: Chapter 3 Installation
Chapter 3: Installation 3.1 Precautions To ensure a long-term and stable performance of the switch, please pay attention to the following before the installation. 1) Safety Requirements: ▪ Before cleaning the switch, cut off the power supply. Do not clean it by the waterish cloth, and never use any other liquid cleaning method. -
Page 9: Installation
3.2 Installation This switch can be either installed on the standard 19-inch mountable rack or located on the desktop. Caution: Please unplug the power cord before installing or removing the switch. 3.2.1 Desktop Installation To install the switch on the desktop, please follow the steps: 1) Set the switch on a flat surface strong enough to support the entire weight of the switch with all fittings. -
Page 10: Rack Installation
3.2.2 Rack Installation To install the switch in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1) Secure the supplied rack-mounting brackets to each side of the switch with supplied screws, as illustrated in the following figure. Figure 5. Attaching Brackets 2) After the brackets are attached to the switch, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure. -
Page 11: Connect To Ground
3.3 Connect to Ground Connecting the switch to ground is to quickly release the lightning over- voltage and over-current of the switch, which is also a necessary measure to protect the body from electric shock. In different environments, the switch may be grounded differently. The following will instruct you to connect the switch to the ground in two ways, connecting to the Grounding Bar or connecting to the Ground via the power cord. -
Page 12: Power On
3.4 Power on The LP-SG2401 24-port Gigabit Ethernet Switch is powered by an AC Power Supply. Connect the switch and power outlet by power cord. Powering on the switch, it will be automatically initialized and the LED indicators should respond as follows: 1) All of the LED indicators will flash momentarily for 2.5 seconds,... -
Page 13: Appendix A: Specifications
Appendix A: Specifications General IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE 802.1p, Standards IEEE802.3x Topology Star Protocol CSMA/CD Ethernet: 10Mbps (Half Duplex) 20Mbps (FullDuplex) Data Transfer Rate Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) Gigabit Ethernet: 2000Mbps (Full Duplex) UTP category 3, 4, 5 cable (maximum 100m) 10BASE-T EIA/TIA-568 100Ω... -
Page 14: Appendix B: Troubleshooting
Appendix B: Troubleshooting 1) The Power LED is not lit Make sure the AC power cord connected the switch with power source properly. Make sure the power source is ON. The Link/Act LED is not lit when a device is connected to the corresponding port Make sure that the cable connectors are firmly plugged into ... -
Page 15: Appendix C: Contact Information
Appendix C: Contact Information For help with the installation or operation of the LP-SG2401 24-port Gigabit Ethernet Switch, please contact us. E-mail: support@lanpro.com Website: http://www.lanpro.com Other LanPro Products: Parabolic Antennas Cabling and Metallic Products Enterprise Data Radios 2.4/3/5.8 GHz Premises antennas... - Page 16 Designed and Manufactured under LanPro standards and specifications. LanPro is a member of One Network Alliance Group of Companies. LanPro products are made in one of the following countries: USA, China, Taiwan, Thailand and Korea. The exact country of origin is unknown.
Need help?
Do you have a question about the LP-SG2401 and is the answer not in the manual?
Questions and answers