Maple Systems HMC3102A-M Quick Start Manual

Quick Start Guide
HMC3102A-M
Description:
HMC3102A-M 800x480 pixels, 10.2" color TFT, with five
expansion slots.
Contents:
—
1 HMC3102A-M (in plastic bag with protective cover sheet
on the screen)
—
1 plastic bag containing 4 mounting clamps (each clamp
consisting of cap nut, bolt, and clamp)
—
1 three prong green power plug*
—
Cardboard package inserts
—
Quick Start Guide
*Note: Connector manufacturer may vary.
Programming software (MAPware-7000), cables, and power
supply purchased separately.
Panel Mounting and Panel Cutout:
HMC3102A-M
Tighten the mounting screws evenly to a torque between 0.4 Nm to
maintain water and dust resistance. Make sure the panel is not dirty
and warped and that it is strong enough to hold the unit.
Note: Maximum Panel thickness (on which unit is to be mounted)
should be 6.0 mm (Tolerance: +/-0.2 mm).
Doc. No. 1011-0303
Specifications:
The HMC3102A-M is a combination operator-based HMI (Human
Machine Interface) with built-in PLC (Programmable Logic
Controller) operation. It communicates with external PLCs over
serial communications ports to read/write data. Five I/O
expansion modules can be attached.
Power: 24VDC +/- 15%, 25W (with 5
expansions)
Display: 10.2" TFT (800 x 480 pixels)
Color graphics display
Bezel: NEMA 4X (IP 66) rated
Touchscreen: 4-wire analog resistive
LEDs: Power indicator
CPU: 32-bit RISC, 454 MHz
Memory: 45 MB Max. Application Memory
Serial Comms (DE9S): Two serial ports
(RS232/RS485/RS422)
USB Slave (Micro Type B): Upload/download projects
USB Host (Standard Type A): Data storage
Ethernet (RJ45): 10/100 Mbps
SD card: Micro SD (high capacity- 4 to 32
GB)
Expansion ports: Five for optional HMC3 I/O
modules
0 to 60° C
Operating temp:
Humidity: 10% to 90% (non-condensing)
Dimensions (WxHxD): 10.55 x 7.48 x 1.30 inches
[268.0 x 190.0 x 33.0mm]
Panel cutout: 10.07 x 7.01 inches
[256.0 x 178.0mm]
Mounting Module to Panel:
Step 2: Tighten clamps evenly to prevent warping. Continue to
tighten until a torque force of 0.4-0.5 Nm is obtained.
Step 3: HMC3102 should be aligned evenly with the cutout with
no warping present after clamps are tightened.
Maple Systems, Inc. 808 134th St SW, Suite 120, Everett, WA 98204-7333 www.maplesystems.com
Port Details (COM1 and COM2):
DB9S (Female) Connector
Note: connect shell to shield of cable.
Grounding:
The HMC3102 should have a good electrical connection to earth
ground via the power connector for safety and to reduce electrical
noise. The HMC unit should be grounded separately from other
high-power systems.
Note: Do not use a ground connection that has potential
impedance (such as painted screws) or is subject to vibration.
Expansion I/O Modules:
The HMC3102A-M has five expansion slots that you can use to
connect I/O modules. Below is a listing of modules currently
available (consult Maple Systems website for additional
information).
HMC3-M1616P: 16 digital input, 16 PNP-type digital
output
HMC3-M1614Y: 16 digital input, 14 digital output
(12 relay, 2 PNP-type)
HMC3-M1212P0200: 12 digital input, 12 PNP-type digital
output, 2 analog input
HMC3-M1212Y0200: 12 digital input, 12 digital output
(10 relay, 2 PNP-type), 2 analog
input
HMC3-M1210P0201: 12 digital input, 10 PNP-type digital
output, 2 analog input and 1 analog
output.
HMC3-M1210Y0201: 12 digital input, 10 digital output (8
relay, 2 PNP-type), 2 analog input,
and 1 analog output.
HMC3-M0808P0401T: 8 digital input, 8 PNP-type digital
output, 4 analog input and 1 analog
output.
HMC3-M0808Y0401T: 8 digital input, 8 digital output (6
relay, 2 PNP-type), 4 analog input,
and 1 analog output.
Rev 02, 11/29/2018