Frigidaire FPBM307NTF Installation Instructions Manual page 24

NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.

I t is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.

D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Part No.:316902912

3/8＂
3/8＂
2＂
Part No.:7 7 2 2 2 3 16902475
PN: 16170000A10767

4" 







13-3/8＂
1/2＂
3/8" TO EDGE
12"

8-1/4＂
IN THE BEFORE NOTE: READ AND IT IS FOLLOW PROCEEDING INSTALLATION VERY IMPORTANT THE DIRECTIONS INSTRUCTIONS TO
READ AND BEFORE NOTE: IT IS IN THE INSTALLATION VERY IMPORTANT FOLLOW THE DIRECTIONS TO outlet. 1. Use mounting This Rear REAR WALL a level plate Wall Template TEMPLATE. and to locate WITH THIS serves to position the horizontal the bottom 12" 3/8" TO EDGE
plate and mounting Wall Template This Rear PROCEEDING outlet. REAR WALL TEMPLATE. to locate INSTRUCTIONS WITH THIS serves to position 12" 3/8" TO EDGE 2. Locate  screw It is right mounted and mark accurately. side of to check important the centerline. at least that the one stud template exhaust is positioned on the left or 4" 
2. Locate  right side and mark accurately. 1. Use a level to check at least of the template that the the horizontal one stud is positioned exhaust the bottom 4"  of the locations 3. Drill holes for the microwave. a stud, that do drill a 3/16" supplied in the to use marked Mark two firmly in a stud locations. additional, bolts. to support at least toggle one wood the weight evenly spaced     Trim the rear wall
microwave. of the screw mounted It is important holes in 3. Drill locations for the centerline. firmly in a stud Mark two supplied to use toggle at least to support additional, one wood the weight evenly on the left or     Trim the rear wall AT THIS  5. Review 4. Remove DO NOT not line the Installation the template toggle bolts. TIME. INSTALL THE MOUNTING from the up with a stud, hole for PLATE wood screws. there 5/8" holes Where drill For holes is for   template along the dotted line.
toggle DO NOT AT THIS TIME.  that do a stud, up with bolts. 3/16" hole not line drill a the marked INSTALL THE MOUNTING a stud, for wood locations. Where there drill 5/8" screws. bolts. For holes holes for is spaced   template along the dotted line. versión Darle vuelta installation a la hoja situation. Instruction rear wall. book for your
the Installation installation 5. Review 4. Remove the template situation. from the Instruction rear wall. book for PLATE your en Español. para consultar la 
Darle vuelta versión en Español. para consultar a la hoja la Locate and mark  
 mounting IMPORTANT: LOCATE THE CENTERLINE. AT LEAST plate. ONE STUD holes to align with holes in the     
and mark mounting Locate IMPORTANT: plate. holes to align with holes       AREA. SPACED MARK THE LOCATION TOGGLE BOLTS FOR 2 ON EITHER IN THE ADDITIONAL, EVENLY SIDE OF   
AT LEAST LOCATE THE CENTERLINE. MARK THE ONE STUD ON EITHER SIDE OF in the    MOUNTING PLATE  
AREA. TOGGLE SPACED BOLTS LOCATION IN THE FOR 2 ADDITIONAL, MOUNTING EVENLY PLATE  Trim the rear wall template along the dotted
  line. 
Trim the rear wall template along the dotted
line.   mounting IMPORTANT: Locate and mark plate. holes to align with holes in the
Locate and mark THE CENTERLINE. LOCATE MARK THE SPACED LOCATION AT LEAST FOR 2 ONE STUD ON EITHER SIDE OF
 IMPORTANT: mounting LOCATE plate. AT LEAST holes to align with holes in the  AREA. TOGGLE IN THE BOLTS MOUNTING ADDITIONAL, PLATE EVENLY
MARK THE SPACED AREA. THE CENTERLINE. LOCATION BOLTS TOGGLE FOR 2 ONE STUD ON EITHER ADDITIONAL, SIDE OF
 IN THE MOUNTING PLATE EVENLY 



6-1/4＂
12-1/2＂
EN-24
Trim the rear wall template along the dotted line.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.

13-3/8＂
3/8＂
2＂
Printed in China

3/8＂