NightStick XPP-5418RX Instruction Manual

Instruction Manual
XPP-5418GX/RX-K01
Please read these instructions before using your Nightstick XPP-5418
Intrinsically Safe Flashlight. They include important safety information and
operating instructions.
THE XPP-5418GX/RX IS APPROVED FOR USE
Bayco Products, Inc.
640 S. Sanden Blvd., Wylie, TX 75098
Ex ia FLASHLIGHT FOR USE IN HAZARDOUS LOCATIONS
CLASS I DIV 1 GRPS A-D T3
E 467756
CLASS II & III DIV 1 GRPS E-G T135ºC
INTRINSICALLY SAFE
CLASS I ZONE 0 AEx ia IIC T3 Ga
SECURITE INTRINSEQUE
Ex ia IIC T3 Ga
0359
II 1 G Ex ia op is IIC T3 Ga
WARNINGS:
Replace batteries in a non-hazardous location.
Use only Energizer AA Model E91 or EN91 batteries.
AVERTISSEMENT:
Remplacer les piles dans une zone non dangereuse.
Utiliser uniquement les piles Energizer AA - modèle E91 ou EN91.
WARNINGS - INTRINSICALLY SAFE
y Warning: Use only the approved non-rechargeable batteries listed below.
y Warning: Do NOT attempt to use rechargeable AA batteries with this light.
y Warning: To prevent ignition of a hazardous atmosphere, do not open
the lens bezel in the hazardous environment. This task must ONLY be
performed in an area known to be non-hazardous.
y Warning: When exchanging batteries, use only Energizer EN91 or
Energizer E91 batteries.
y Warning: To prevent ignition of a hazardous atmosphere, the AA batteries
must only be exchanged in an area known to be non-hazardous.
y Warning: To reduce the risk of explosion, do not mix new batteries with
used batteries, or mix batteries from different manufacturers.
y Warning: Substitution of components may impair intrinsic safety.
SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY
y For personal safety, always confirm the rating of any known hazardous or
potentially hazardous location where the light is to be used.
BATTERY INSTALLATION
WARNING: In order to maintain the XPP-5418's Intrinsically Safe rating,
the only AA batteries certified for use with this light are the Energizer
EN91 or Energizer E91 batteries.
y Do not attempt to use any other brand or model of AA batteries.
y Do not attempt to use any type of rechargeable AA batteries.
Warning: To prevent ignition of a hazardous atmosphere, do not
remove the lens bezel or the reflector / battery carrier in the hazardous
environment. This task must ONLY be done in an area known to be
non-hazardous.
y Loosen the locking screw located on the side of the lens cap. NOTE:
Do NOT attempt to completely remove the locking screw. Doing so is not
necessary and may damage the threads. The screw simply needs to be
loosened enough to allow the lens bezel to unscrew.
y Unscrew the lens bezel from the housing in a counter-clockwise direction.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
XPP-5418GX/RX
Ex ia op is IIC T3 Ga
Intertek ITS 13 ATEX27837X
IECEx ITS 16.0067X
-20ºC ≤ Tamb ≤ +40ºC
1.5V/Cell with three in series
Energizer E91 or EN91
THE XPP-5418-K01 COMES WITH THE NS-HMC6 MULTI-ANGLE MOUNT
THAT CAN BE ATTACHED TO ANY FIRE HELMET OR HARD HAT.
Segurança
on what type of mount is needed.
INMETRO
Ex ia op is IIC T3 Ga
(-20ºC ≤ Tamb ≤ +40ºC)
NCC
15.0286 X
ASSEMBLY
in order to position the light appropriately for the optimum clearance and
illumination.
INS-XPP-5418GX/RX-K01-18
XPP-5418 with Brim Mount
y Turn the light upside down and carefully shake the light in order to remove
the batteries. Allow the batteries to slide into your hand.
y Using 3 – AA Energizer EN91 or Energizer E91 batteries (make sure
that all 3 batteries are of the same model), install the batteries in the carrier
paying close attention to the markings inside the housing for proper battery
terminal polarity alignment.
y Replace the lens bezel by screwing it onto the housing in a clockwise
direction.
y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may
damage the threads and impact the light's Intrinsic Safety.
ATTACHING HELMET MOUNT
Two mounting components are included that can be changed depending
y Brim Mount - Mounts on brim of helmet or hard hat..
y Slot Mount - Slides into helmet accessory slot.
NS-HMC6 Helmet Mount Kit
y Fit the Light Mount (A) into the slot of either the Brim Mount or Slot Mount
(B) and securely tighten using the thumb screw (C).
y Securely attach the brim or slot mount to the helmet.
y Place the flashlight inside the Light Mount
SET THE ANGLE OF THE MULTI-ANGLE MOUNT
Once mounted to the helmet, the user can change the angle of the mount
XPP-5418 with Slot Mount
07-18-2018