Advertisement
Pre-wire or Pre-construction
Locate all obstructions (AC wiring, plumbing, duct work, studs, and joists).
Route the speaker wire to the speaker location avoiding all obstacles. Watch
out for closeness to AC wiring.
Russound offers Speaker Rough-In Brackets that can be fastened to the
adjacent studs. Once the dry wall is installed, the opening is cut out. There are
holes molded into the bracket for speaker wire tie-off to keep the wire from
being lost during construction.
Make sure the speaker cutout (hole) doesn't extend further than 1/4" (0.6 cm)
from the inside of the mounting bracket.
In-ceiling bracket Installation
Speaker Cable
In-wall bracket Installation
Retrofit Installation
Locate existing pipes, duct work, and AC wiring before cutting any holes in
the ceiling.
1.
Center the cardboard template between adjacent joists, avoiding all
wiring, pipes, duct work, and lightly mark the outline with a pencil.
Then use a keyhole/drywall saw or motorized spiral-cut tool to make
the opening.
2.
Score the outline of the template with a utility knife to prevent
chipping. If dealing with lath and plaster or thick paneling, drill 1"
(2.5 cm) holes in several places around the pencil outline. Use a
fine-toothed keyhole saw or hacksaw blade with slow strokes to saw
through and remove the inner surface.
Score template outline
Retrofit Installation
Russound Architectural Series of In-Ceiling and In-Wall Loudspeakers
3
Rough-in Bracket
Stud / Joist
Screw
Note:
Run two pair conductors for
single point speakers.
Magnetic square grille
ICG-6S (6" Models) and
ICG-8S (8" models)
(sold separately)
Cut out opening
PREPARATION / SPEAKER PLACEMENT
Additional Tips / Considerations
Try to run speaker wires after AC wiring is in so you can separate the wires,
•
avoiding induced noise caused by close parallel positioning of the two
wire types.
Secure speaker wires in place against a stud along vertical runs. Do not
•
pierce the wire insulation. Allow a bit of slack for expansion of building
materials.
Route horizontal wire runs through holes drilled in studs at roughly equal
•
heights.
Speakers should not be installed until the wallboard is in place. In the
•
meantime, leave several feet of wire coiled up and secured to the back
side of the mounting frame. Excess length can be removed during final
assembly.
When installing the drywall, make sure the speaker cutout hole doesn't
•
extend farther than 1/4" (0.6 cm) from the inside of the mounting frame.
Speakers installed in ceilings should have a safety wire tied between
•
the back of the speaker and the frame of the building. Use any strong
insulated wire, connect it to the speaker frame or baffle so it doesn't
interfere with the speaker's operation. The other end should be firmly
attached to the joist or flooring above using a hook, nail, or other reliable
fastener.
Terminating the wires in an outlet box attached to a stud or retrofit
•
junction box at the exit location. Use an outlet plate with speaker wire
terminations.
After the drywall is secured and finished, install the speakers as we've
•
described.
Painting the Speaker Grille
Russound Architectural Speaker Grilles have a designer white finish that can
be painted with ordinary latex paint. Remove the speaker grille from the
speaker before painting.
1. Remove the magnetic speaker grille and carefully remove the scrim cloth
from the grille and set aside.
2. Paint the grille. Russound recommends diluting the latex paint with water
4:1 or 5:1 proportionally. Due to the fine mesh openings, using several layers of
a thinner paint spray is recommended rather than using a single, thicker coat.
A thick coat is likely to clog the speaker grille openings.
3. While the paint is still wet on the grille, and the grille is not attached to the
frame, use a gentle burst of compressed air against the outside surface to clear
the fine holes in the mesh.
4. After the paint has thoroughly dried, re-attach the scrim cloth, and attach
the grille to the frame.
Do not attach the grille until the
speaker has been connected and
secured in the ceiling.
Speaker Assembly
Speaker
Scrim Cloth
Grille
Advertisement
