Summary of Contents for NemaVision-iPC NV-HMI-717P
Page 1
NemaVision-iPC NV-HMI-717/721 (P) (SBC-7106A) User Manual Release Date Revision Sep. 2014 V1.0 NV-HMI-7XX User Manual...
Page 2
Warning!_____________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ Adaptor □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to prevent your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆...
Chapter 1 Getting Started 1.1 Specifications NV-HMI-717(P) NV-HMI-721(P) System Onboard Intel Atom Cedar View D2550 1.86GHz Dual Core Processors Chipset Intel NM10 Express Chipset Memory Onboard 4GB DDR III 800 MHz IO Port 2 x USB 2.0 type A Serial/Parallel 1 x RS-232 DB-9 1 x DB-9 RS-232/422/485 (Default RS-232) Audio...
Page 7
Contrast Ratio 800:1 3000:1 View angle(H°/V°) 160 / 140 178 / 178 Touch Screen – Resistive Touch Window Type TS Control IC PenMount 6000 on Board Interface RS-232 interface Light Over 80% Transmission(%) Touch Screen – Projected Capacitive Type TS Control IC Chip on tail Interface USB interface...
Page 8
It will need install the correct driver by LCD panel size/resolution, totally four version : 800*480, 800*600, 1024*768(18bit), 1024*768(24bit) The original driver not support VGA display will have to customize NV-HMI-7XX User Manual...
1.3 Brief Description of NV-HMI-7XX NV-HMI-717 and NV-HMI-721 are Industrial Compact Size Panel PC in NV-HMI series, which comes with flat front panel touch screen and fanless design. It is powered by Intel Atom D2550 1.8GHz CPU built-in, 4GB DDR III 800 MHz. NV-HMI series is 9~36VDC wide-ranging power input and IP65 compliant front panel.
Page 12
Figure 1.5: Rear View of NV-HMI-721 Figure 1.6: Rear View of NV-HMI -721 NV-HMI-7XX User Manual...
1.4 Installation of HDD (NV-HMI-717/NV-HMI-721) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 You can put or remove HDD into the machine by pulling the HDD bracket. Step 3 You can remove HDD by unscrewing 4 screws in the HDD bracket.
Page 14
Step 4 There is a SD hole in the side of machine. You can replace SD card from there NV-HMI-7XX User Manual...
Chapter 2 Hardware 2.1 Mainboard Introduction SBC-7106A is a 4" industrial motherboard developed on the basis of Intel Cedarview-M/D Processors and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE configuration,one VGA port, one HDMI port, one LVDS interface.
Page 16
1 x SD Socket (USB to SD) Ethernet 2 x PCIe Gbe LAN by Intel 82574L 2 x USB 2.0 (type A)stack ports (USB4/USB5) 2 x USB 2.0 Pin header for CN3 (USB2/USB3) 1 x USB 2.0 Pin header for CN1 (USB0,option) 1 x USB 2.0 Pin header for CN2 (USB1) 1 x USB 2.0 for MPCIE1 (USB7) 1 x RS232/RS422/RS485 port, DB9 connector for external...
2 x RJ45 GbE LAN Ports 1 x HDMI Port 1 x Stack audio Jack (Line out) Software programmable 1 – 255 second by Super I/O Watchdog Timer Operating: -20℃ to 70℃ Temperature Storage: -40℃ to 85℃ Humidity 5% - 95%, non-condensing, operating Power 12V /0.95A (Intel Atom N2600...
2.3 Jumpers and Connectors Location Figure 2.2: Jumpers and Connectors Location- Board Top Figure 2.3: Jumpers and Connectors Location- Board Bottom NV-HMI-7XX User Manual...
2.4 Jumpers Setting and Connectors 1. CPU1: (FCBGA559), onboard Intel Intel Cedarview-M/D Processors Model SBC-7106A-D25-4G D2550 D2550(option) SBC-7106A-D25P-4G N2600(option) SBC-7106A-N26-2G 2. H3/H4/H5/H6: CPU1 and U53 Heat Sink Screw holes, four screw holes for intel D2550 (or N2600) and NM10 Heat Sink assemble. 3.
Page 20
Procedures of CMOS clear: a) Turn off the system and unplug the power cord from the power outlet. b) To clear the CMOS settings, use the jumper cap to close pins 1 and 2 for about 3 seconds then reinstall the jumper clip back to pins open. c) Power on the system again.
Page 21
9. CPU_FAN1: (2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup. Pin# Signal Name Ground Rotation detection Note: Output power of cooling fan must be limited under 5W. Model CPU_FAN1 SBC-7106A-D25...
Page 22
11. HDMI1: (HDMI 19P Connector), High Definition Multimedia Interface connector. 12. JP6: (2.0mm Pitch 2x2 Pin Header), LVDS jumper setting. Function (CN1) Pin1-Pin2(Close) Single channel LVDS Pin1-Pin2(Open) Dual channel LVDS (Default) Pin3-Pin4(Close) 8/24 bit (Default) Pin3-Pin4(Open) 6/18 bit 13. U66: AT24C02-DIP8,The EEPROM IC(U66)is the set of LVDS resolution.
Page 23
Ground Ground BKLT_EN_OUT BKLT_CTRL Note: Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu. 15. CN1: (1.25mm Pitch 2x20 Connector, DF13A-40DP-1.25V), For 18/24-bit LVDS2 output connector, Fully supported by Parad PS8625(DP to LVDS), the interface features dual channel 24-bit output.
Page 24
JP1 Pin# Function Close 1-2 COM1 RI (Ring Indicator) (default) Close 3-4 COM1 Pin9:DC+5V (option) Close 5-6 COM1 Pin9:DC+12V (option) 17. S_232: (Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output. Function S_232 Pin# RS232 (Default) Pin1, Pin2, Pin3, Pin4 RS422...
Page 25
RS232 (Default): Pin# Signal Name DCD# (Data Carrier Detect) RXD (Received Data) TXD (Transmit Data) DTR (Data Terminal Ready) Ground DSR (Data Set Ready) RTS (Request To Send) CTS (Clear To Send) JP1 select Setting (RI/5V/12V) BIOS Setup: Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-232】...
Page 26
BIOS Setup: Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-485】 20. JP2: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP2 Pin# Function Close 1-2 COM2 RI (Ring Indicator) (default) COM2 Pin9:DC+5V (option) Close 3-4...
Page 27
23. TCH1: (2.0mm Pitch 1x6 wafer Pin Header), internal Touch controller connector. Pin# Signal Name SENSE GND_EARCH 24. LED1, LED2, LED3 (option): LED1: LED STATUS. Green LED for Motherboard Power status. LED2: LED STATUS. Green LED for Motherboard Standby Power Good status. LED3: LED STATUS.
Page 28
with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is 30x30mm. 30. H1/H2: MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx30mm) assemble. 31. AUDIO: (2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used to provide high-quality audio I/O ports.
Page 29
34. LAN1/LAN2: LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45 Ethernet ports are provided. Used intel 82574L chipset, LINK LED (green) and ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN. 35.
Page 30
two USB 2.0,one PS/2 mouse,one PS/2 keyboard, two uart,one PCIe x1,one SMbus. connected to the TB-528 riser Card. Function Signal Name Pin# Signal Name Function 5V_S5_USB 5V_S5_USB 5V_S5_USB 5V_S5_USB USB23_OC CLKREQPSON_ATX- USB2 USB2_N USB2_P USB2 USB3 USB3_N USB3_P USB3 Ground Ground PS/2 MS PS2_MSCLK...
Page 31
CN3: (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header. M-PCIE1: (Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0(USB2),Smbus,SIM and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm. Signal Name Function support PCIe 1X USB2.0 (USB2)
Page 32
Pin# Signal Name KBDATA MSDATA Ground KBCLK MSCLK GPIO1: (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Signal Name Pin# Pin# Signal Name Ground SMB_DATA_R SMB_CLK_R ICH_GPIO13_IN1 ICH_GPIO24_IN2 ICH_GPIO26_IN3 ICH_GPIO27_IN4 USB_23:...
Page 33
Close 3-4 COM5 Pin9=+5V (option) Close 5-6 COM5 Pin9=+12V (option) COM5: (Type DB9),serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI or 5V or 12v, For details, please refer to description of JP3.
Page 34
Pin# Signal Name DCD# (Data Carrier Detect) RXD (Received Data) TXD (Transmit Data) DTR (Data Terminal Ready) Ground DSR (Data Set Ready) RTS (Request To Send) CTS (Clear To Send) JP6 Setting: Pin1-2 : RI (Ring Indicator) (default) Pin3-4 : 5V Standby power (option) Pin5-6:12V Standby power (option)
Page 35
CN3: (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header. LED1: Mini PCIe devices LED Status. PS2: (2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used. Pin# Signal Name KBDATA...
Page 36
ICH_GPIO24_IN2 ICH_GPIO26_IN3 ICH_GPIO27_IN4 USB_23: (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s. Signal Name Pin# Pin# Signal Name 5V_USB23 5V_USB23 USB3_N USB2_N USB3_P USB2_P Ground Ground Ground Note: Before connection, make sure that pinout of the USB Cable is in accordance with that of...
Page 37
DTR (Data Terminal Ready) Ground DSR (Data Set Ready) RTS (Request To Send) CTS (Clear To Send) JP5 Setting: Pin1-2 : RI (Ring Indicator) (default) Pin3-4 : 5V Standby power (option) Pin5-6:12V Standby power (option) JP6: (2.0mm Pitch 2x3 Pin Header),COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.
Page 38
COM_6(option): (2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection. Signal Name Pin# Pin# Signal Name Ground JP6 Setting: RI/5V/12V 40. TB-528C1U2P1/TB-528C1U2 (option): SBC-7106A Riser Card,TB-528C1U2P1 CN3 connect to SBC-7106A CN3 pin Header. TB-528C1U2P1 Top:...
Page 39
H1/H2: MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble. LED1: Mini PCIe devices LED Status. SIM1(option): (SIM Socket 6 Pin), Support SIM Card devices. PS_ON1: (2.0mm Pitch 1X2 Pin Wafer), ATX Power and Auto Power on jumper setting. PS_ON Mode Close 1-2...
Page 40
Signal Name Pin# Pin# Signal Name Ground SMB_DATA_R SMB_CLK_R ICH_GPIO13_IN1 ICH_GPIO24_IN2 ICH_GPIO26_IN3 ICH_GPIO27_IN4 USB23: (Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports, speed up to 480Mb/s. USB_23(option): (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s.
Page 41
COM5: (Type DB9),serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI or 5V or 12v, For details, please refer to description of JP3. Pin# Signal Name DCD# (Data Carrier Detect)
Page 42
Pin# Signal Name DCD# (Data Carrier Detect) RXD (Received Data) TXD (Transmit Data) DTR (Data Terminal Ready) Ground DSR (Data Set Ready) RTS (Request To Send) CTS (Clear To Send) JP6 Setting: Pin1-2 : RI (Ring Indicator) (default) Pin3-4 : 5V Standby power (option) Pin5-6:12V Standby power (option)
Page 43
CN3: (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header. M-PCIE1: (Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices with Smbus,USB2.0,SIM and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm. Signal Name Function support PCIe 1X USB2.0 (USB2)
Page 44
PS2: (2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used. Pin# Signal Name KBDATA MSDATA Ground KBCLK MSCLK USB_IN(option): (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB port via a dedicated USB cable, speed up to 480Mb/s.
Page 45
JP3 Pin# Function Close 1-2 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) COM6: (2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection. Signal Name Pin# Pin#...
Page 46
JP1: (2.0mm Pitch 1x2 Pin Header), Reserve. JP2: (2.0mm Pitch 1x2 Pin Header), Reserve. CAN1/CAN2: (3.5mm Pitch 1x10 Pin connector), it provides two CAN-bus Interface. Pin# Chann Signal Function Name CANL2 CAN bus Signal L Terminal resistor R-(internally connected to CANL2) CAN2 Shield cable (FG) Terminal resistor R+( internally connected to CANH2)
Page 47
CN3: (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header. USB23: (Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports, speed up to 480Mb/s. NV-HMI-7XX User Manual...
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup. After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. 3.2 BIOS Setup Utility Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.
System Time: Set the system time, the time format is: Hour : 0 to 23 Minute : 0 to 59 Second : 0 to 59 System Date: Set the system date, the date format is: Note that the ‘Day’ automatically changes when you set the date. Day: Month: 01 to 12 Date:...
Page 51
[32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks] VGA Palette Snoop: [Disabled] [Enabled] PERR# Generation: [Disabled] [Enabled] SERR# Generation: [Disabled]...
Page 52
S3 Video Repost: [Disabled] [Enabled] 3.4.3 CPU Configuration Processer Type Intel(R) Atom™ CPU D2550 EMT64 Supported Processor Speed 1865 MHz System Bus Speed 533MHz Ratio Status Actual Ratio System Bus Speed 533 MHz Processor Stepping 30661 Microcode Revision L1 Cache RAM 2x56 k L2 Cache RAM 2x512 k...
Page 53
Active Trip Point Hi [71C] Passive Trip Point [95] Passive TC1 Value Passive TC2 Value Passive TSP Value 3.4.5 IDE Configuration SATA Port0 Not Present SATA Port1 Not Present SATA Controller(S): [Enabled] [Disabled] Configure SATA as: [IDE] [AHCI] Misc Configuration for hard disk 3.4.6 USB Configuration USB Configuration USB Devices:...
Page 54
[Auto] [Manual] 3.4.7 W83627UHG Super IO Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration UART Mode Selection: [RS-232] [RS-485] [RS-422] Serial Port 2 Configuration Serial Port 3 Configuration UART Mode Selection: [RS-485] [RS-422] Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration 3.4.8 W83627UHG HW Monitor PC Health Status...
Page 55
[Disabled] Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] [Enabled] Console Redirection Settings 3.4.10 PPM Configuration PPM Configuration EIST: [Enabled] [Disabled] CPU C state Report [Enabled] [Disabled] Enhanced C state [Enabled] [Disabled] CPU Hard C4E [Enabled] [Disabled]...
3.5 Chipset Settings 3.5.1 Host Bridge ►Memory Frequency and Timing ►Intel IGD Configuration ******* Memory Information ******* Memory Frequency 1067 MHz(DDR3) Total Memory 4096 MB DIMM#0 Not Present DIMM#1 4096 MB Memory Frequency and Timing MRC Fast Boot [Enabled] [Disabled] Max TOLUD [Dynamic] [1GB]...
[Do not Launch] [UEFI only] Launch Video OpROM po [Legacy only] [Do not Launch] [UEFI only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] 3.7 Security Settings 3.7.1 Administrator Password 3.7.2 User Password NV-HMI-7XX User Manual...
Type the password with up to 20 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press Enter key. You may press Esc key to abandon password entry operation.
Page 63
Save Changes and Exit Save & Exit Setup save Configuration and exit ? [Yes] [No] Discard Changes and Ext Exit Without Saving Quit without saving? [Yes] [No] Save Changes and Reset Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset without saving? [Yes]...
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows 7. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver Installation instructions are given below. Important Note: After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of...
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset NM10 Express from the list Step 2. Click Next to setup program. NV-HMI-7XX User Manual...
Page 66
Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue. NV-HMI-7XX User Manual...
Page 67
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation media from the drives. NV-HMI-7XX User Manual...
4.2 Intel Graphics Media Accelerator Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) VGA Chipset Driver. Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop theme(if supported). Click Next. NV-HMI-7XX User Manual...
Page 70
Step 5. Click Next. Step 6. To restart the computer, select Yes, I want to restart this computer now. Then click Finish. NV-HMI-7XX User Manual...
4.3 Intel (R) Network Adapter To install the Intel (R) Network Adapter device driver, please follow the steps below. Step 1. Select LAN Driver. Step 2. Select NV-HMI-17”~21”. NV-HMI-7XX User Manual...
Page 72
Step 3. Click Next to Continue. Step 4. Read license agreement. Click I accept the terms in the license agreement. Click Next NV-HMI-7XX User Manual...
Page 73
Step 5. Click Advanced Network Services. Then click Next to Continue. Step 6. Click Install to begin the installation. NV-HMI-7XX User Manual...
Step 7. Click Finish to exit the wizard. 4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below. Step 1. Select Realtek AL662 Audio Codec Driver from the list NV-HMI-7XX User Manual...
Page 75
Step 2. Click Next to continue. Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation. NV-HMI-7XX User Manual...
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems. 5.1 Windows 2000/2003/Vista/WIN7 Universal Driver Installation for PenMount 6000 Series Before installing the Windows 2000/WIN7 driver software, you must have the Windows 2000/WIN 7 system installed and running on your computer.
Page 77
Step 2. Select Resistive Touch. Step 3. Click Next to continue. NV-HMI-7XX User Manual...
Page 78
Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation. NV-HMI-7XX User Manual...
Page 79
Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyway. NV-HMI-7XX User Manual...
Step 13. Click Yes to do 4 point calibration. 5.2 Software Functions 5.2.1 Software Functions(Resistive Touch) Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1.
Page 87
Standard Calibration Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press ‘ESC’. Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens.
Page 88
Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the step as below: NV-HMI-7XX User Manual...
Page 89
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy. NV-HMI-7XX User Manual...
Page 90
Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration. Turn off EEPROM storage The function disable for calibration data to write in Controller.
Page 91
About This panel displays information about the PenMount controller and driver version. NV-HMI-7XX User Manual...
Page 92
Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/WIN 7 support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit.
Page 93
2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens. Touching all screens completes the mapping and the desktop reappears on the monitors. Select a display and execute the “Calibration”...
Page 94
6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear. Touch the red squares in sequence. 8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.
Page 95
Control Panel Open Control Panel Windows Beep Setting Beep function for each device Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button functions.
5.2.2 Software Functions(Projected Capacitive) General In this window, you can see there is USB Controller. Click OK to continue. Monitor Mapping to adjust touch panel to search for device NV-HMI-7XX User Manual...
Page 97
Setting Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode NV-HMI-7XX User Manual...
Page 98
Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time NV-HMI-7XX User Manual...
Page 99
Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy. NV-HMI-7XX User Manual...
Page 100
Display In this window, it shows the mode of display. Enable Multiple Monitors. Map to main display if system has only one display monitor Full Screen Lower Screen Left Screen Upper Screen Right Screen NV-HMI-7XX User Manual...
Page 101
Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function. NV-HMI-7XX User Manual...
Page 102
Hardware Saturn Hardware Configuration NV-HMI-7XX User Manual...
Page 103
About To display information about eGalaxTouch and its version. NV-HMI-7XX User Manual...