Hoagie bun toaster with electronic timer (10 pages)
Summary of Contents for Wells FT-18M
Page 1
Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
Page 2
Seller’s obligation under this warranty is limited to the one year from the date of original installation or 18 months repair of defects without charge by a Wells Mfg. Co. factory from the date of shipment from our factory, whichever...
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
Do not operate this appliance if the keypad section of the control panel DO NOT connect or is torn or broken. Call your Authorized Wells Service Agent for service. energize this appliance The technical content of this manual, including any wiring diagrams,...
AGENCY LISTING INFORMATION This appliance conforms to NSF Standard 4 for sanitation only if installed in accordance with the supplied Installation Instructions and STD 4 maintained according to the instructions in this manual. This appliance is Listed under UL File E6070 for 208V and 240V. E6070 This appliance is Listed under UL File E6070 for 208V and 240V .
Page 7
OPERATION WARM-UP CAUTION: BURN HAZARD During warm-up, both displays flash while showing the last-used MENU temperature setpoint. Exposed portions of toaster A MENU cycle cannot be started while in warm-up mode. are hot. Use care when working around the platens. When setpoint temperature is reached, the display stops flashing and Use insulated handles to the audible alert beeps 3 times.
CLEANING CAUTION: CLEANING INSTRUCTIONS ELECTRIC SHOCK PRECAUTIONS: Press MENU 4 (cleaning mode). Allow toaster to HAZARD cool to 275ºF. DO NOT submerge or NOTE: If MENU 4 has been programmed to immerse toaster in water. anything other than 275ºF, press POWER SWITCH OFF and allow unit to cool for at least 10 minutes.
Teflon™ non-stick sheets are black on one side and brown on the other. Either side may be used. For consistency, Wells recommends using the same color side on both platens. Wrap the sheet smoothly around the bottom face of the platen.
Page 10
MAINTENANCE PROCEDURES (continued) CAUTION: ADJUST PLATEN TENSION BURN HAZARD 1. ADJUSTMENT LOCATION Unplug toaster and allow to a. Right platen tension adjuster is located on back of the toaster, cool before adjusting. on back side of the right upright. b. Left platen tension adjuster is located on back of the toaster, on front side of the left upright.
Page 11
MAINTENANCE PROCEDURES (continued) PROGRAMMING INSTRUCTIONS: CAUTION: BURN HAZARD A. Controller can be configured for use in four different modes: a. Single operation with manual timer Avoid contact with appliance b. Single operation with automatic timer heating surfaces. c. Single and remote operation with manual timer d.
Page 12
Enter the 4-digit code. (NOTE: Factory setting is left MENU 1, left MENU 2, left MENU3, left MENU 4. Contact your Wells Authorized Service Agency for instructions in determining or changing your access code). Starting with the first digit, the bottom bar of the display moves to the top bar.
Page 13
MAINTENANCE PROCEDURES (continued) When in program mode, the Set the time with MENU 3 (increase) and MENU 4 (decrease). Press timer is displayed as 4 digits TEMP to save the time. (i.e. 00:15). In regular mode, The display will now advance to show zone temperature setpoints: the timer is displayed as 3 1.450 = Zone 1 @ 450ºF digits (i.e.
Unplugged or circuit breaker tripped Plug toaster into appropriate circuit. (no lights or display) Reset circuit breaker Damaged cord or plug Contact your Authorized Wells Service Agency for repairs One side does not heat Zone temp not programmed Program zone temp (see pg. 8)
TEFLON™ NON-STICK SHEETS For factory authorized (pkg of 4) 22876 service, or to order factory authorized replacement TEFLON™ NON-STICK SHEETS parts, contact your Wells (pkg of 4) PLUS authorized service agency, 4ea. RETAINING RODS 22877 or call: Wells Manufacturing Co.