Related Manuals for Chapman Machinery TF Series
Summary of Contents for Chapman Machinery TF Series
- Page 1 TF Series Trailed Feeder (All Models) Original Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: 01288 308149 Email: sales@chapman.co.uk...
-
Page 2: Table Of Contents
The information contained in this manual is correct at the time of going to press. However, in the course of development, changes in specification are inevitable. Should you find the information given differs from your machine, please contact Chapman Machinery Ltd direct for advice. Use only Chapman Genuine Service Parts on Chapman Machinery and Machines. -
Page 3: Hse Information
HSE Information Safe use of all-terrain vehicles (ATVs) in agriculture and forestry – AIS Sheet 33 Remember that your ability to control the ATV by your body Introduction movements will be considerably reduced when carrying a load or towing a trailer. This information sheet gives advice on the safe use of ATVs. -
Page 4: Important Safety Information
Important Safety Information Always read this manual before fitting or operating the machine – whenever any doubt exists contact your dealer or the Chapman Machinery Service Department for advice and assistance. DEFINITIONS The following definitions apply throughout this manual: WARNING - An operating procedure, technique etc., which can result in personal injury or loss of life if not observed carefully. -
Page 5: Description
Description The TF Series Trailed Feeders are designed for feeding livestock, through deposition of pre-defined drops of feed, onto clear ground. The TF Series operate with an electric motor mechanism, ensuring accurate disposition, and industry leading ground clearance. The rotor and wiring mechanism are all IP67 rated, to ensure trouble-free usage in even the toughest winter conditions. -
Page 6: Implement Decals
Implement Decals If your implement does not contain all of the decals shown below, please contact Chapman Machinery for replacement decals before use. Note: All decals must be present and visible. It is imperative that these are replaced if damaged to prevent potential harm to users. -
Page 7: Attachment
Attachment Before Attaching the Machine Before attachment, ALWAYS ensure the following: - All safety guards & decals are in good working order and correctly fitted - Lubrication points have been lubricated as per scheduled maintenance period - The tyres are free of damage and inflated to the correct pressure - Electrical connections are free of dirt and moisture Attaching the Machine NOTE: This machine is designed to attach to the towing vehicle through a 50mm diameter ball hitch. -
Page 8: Drop Size Adjustment & Calibration
Drop Size Adjustment & Calibration Initially set the Feed adjustment plate to setting 4, as indicated by the arrow on the drop adjustment plate. To adjust, loosen BOTH hand wheels, and slide the unit forwards or backwards to the desired value. Tighten securely. Setting 1: Minimum drop size Setting 8: Maximum drop size Fill the hopper 50% full of the feed to be distributed. -
Page 9: Sensor Change / Adjustment
Sensor Change / Adjustment If your control box is showing an F1 error and not counting correctly, you may have a problem with the connectors and/or the sensor may need adjustment. First, check the plug and socket connection between the control box and the feeder – THIS IS THE MOST COMMON CAUSE OF PROBLEMS! If required check continuity with a multi-meter. - Page 10 3. In the Picture below you can see the sensor (with the wire) and the magnet (fitted to the disc) are facing each other with approximately 2mm gap between them. The sensors also need to be aligned vertically (so that they are approximately level with each other). If required you can bend the sensor support bracket up or down to get vertical alignment, and you can move the sensor in or out on the slotted holes to get horizontal alignment.
-
Page 11: Control Box
Control Box 4 Button Model (FROM October 2015) The 4-button model has two modes of operation; - Count Mode: Unit counts up from 0 e.g. 1,2,3,4,5 indefinitely, until the count is paused or the unit switched off. If the counter reaches 999 then it will reset to 000. - Countdown Mode: The desired drop count is set using the up / down arrows in increments of 5. - Page 12 OPERATION - COUNT MODE 1. Switch the unit on by pressing the ON / OFF button. All segments of the display will light up. 2. After approx. 3 seconds the display will show 000. 3. Press Run / Pause to start the motor. The unit will count up from 0. Pressing RUN / PAUSE when the unit is running will stop the motor and pause the counter.
-
Page 13: Operating Limits & Recommendations
Operating Limits & Recommendations Ensure that the operator is suitably qualified to use a machine of this nature and that they have fully read understood this manual - they should be aware of all safety aspects relating to the safe use of the machine. -
Page 14: Troubleshooting
Troubleshooting Problem Possible Causes Remedies Unit will not light up when on Low Supply Power Charge Battery button pressed Incorrect Polarity / poor Check connection connection Fuse blown (2 button controls Replace Fuse only) Shortage in wiring Check wiring loom for damage and repair / replace as required Motor does not operate even Poor connection between control... -
Page 15: Warranty
The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship. - Page 16 EC DECLARATION OF CONFORMITY Machinery Directive 2006/42/EC Chapman Machinery Ltd Hele Barton Week St. Mary Holsworthy Devon EX22 6XR The Products Covered by this Declaration Product: TF350 Trailed Livestock Feeder & Options (Off-Highway) Standards and Regulations used: Machinery Directive 2006/42/EC...