1. Manuals
  2. Brands
  3. Youjie Manuals
  4. Scanner
  5. Voyager 1400g Series
  6. User manual

Youjie Voyager 1400g Series User Manual

Area-imaging scanner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Leitor
Voyager 1400g
O leitor de código de barras Voyager 1400g, da
Honeywell, é um scanner para leituras 2D. Este Linear
Imager é capaz de ler até mesmo linhas ou imagens de
má qualidade.
www.bztech.com.br

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Voyager 1400g Series and is the answer not in the manual?

Questions and answers

Related Manuals for Youjie Voyager 1400g Series

Summary of Contents for Youjie Voyager 1400g Series

  • Page 1 Leitor Voyager 1400g O leitor de código de barras Voyager 1400g, da Honeywell, é um scanner para leituras 2D. Este Linear Imager é capaz de ler até mesmo linhas ou imagens de má qualidade. www.bztech.com.br...
  • Page 2 Voyager™ 1400g Series Area-Imaging Scanner User’s Guide ™...
  • Page 3 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in speci- fications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not repre- sent a commitment on the part of HII.
  • Page 4 Product Agency Compliance FCC Part 15 Subpart B Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
  • Page 5 UL Statement UL listed: UL60950-1, 2nd Edition. Canada Industry Canada ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Opera- tion is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
  • Page 6 Honeywell Scanning & Mobility Product Environmental Information Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information. Australia/NZ C-Tick Statement Conforms to AS/NZS 3548 EMC requirement Russia Gost-R certificate South Korea The product meets Korean agency approval for Class B equipment: 이...
  • Page 7 Patents For patent information, please refer to www.hsmpats.com. Solids and Water Protection The Voyager 1400g has a rating of IP42, immunity of foreign particles and drip- ping water. Warning To reduce the possibility of heat-related injuries, avoid touching sec- tions of the scanner that feel warm.
  • Page 8 Required Safety Labels Compliance Markings information, Part Number, and Serial Number information Compliance Markings information...

  • Page 10: Table Of Contents

    Table of Contents Chapter 1 - Getting Started About This Manual ............1-1 Unpacking Your Device..........1-1 Connecting the Device ..........1-1 Connecting with USB ..........1-1 Connecting with Keyboard Wedge ......1-2 Connecting with RS232 Serial Port ....... 1-4 Connecting with RS485.........
  • Page 11 Wincor Nixdorf Beetle™ Terminal Default Settings ..2-8 Keyboard Country Layout ..........2-9 Keyboard Style ............2-15 Keyboard Conversion ..........2-17 Control Character Output...........2-17 Keyboard Modifiers............2-18 RS232 Baud Rate............2-20 RS232 Word Length: Data Bits, Stop Bits, and Parity ..............2-21 RS232 Receiver Time-Out.........2-22 RS232 Handshaking..........2-22 RS232 Timeout ............
  • Page 12 In-Stand Sensor Mode ..........3-6 Presentation Mode ............3-7 Idle Illumination - Presentation Mode ....3-7 Presentation Sensitivity ......... 3-7 Presentation Centering.......... 3-8 ® CodeGate ..............3-9 Mobile Phone Read Mode......... 3-10 Hands Free Time-Out ..........3-10 Reread Delay ............3-10 User-Specified Reread Delay........
  • Page 13 Data Format Editor Commands ........5-4 Move Commands........... 5-5 Search Commands ..........5-5 Miscellaneous Commands........5-6 Data Formatter.............5-7 Primary/Alternate Data Formats ........5-8 Chapter 6 - Symbologies All Symbologies ............6-2 Message Length Description ........6-2 Codabar ...............6-3 Codabar Concatenation ......... 6-4 Code 39 ...............6-6 Code 32 Pharmaceutical (PARAF) ......
  • Page 14 ISBN Translate ............ 6-34 EAN/JAN-8 ..............6-35 MSI ................6-37 GS1 DataBar Omnidirectional ........6-39 GS1 DataBar Limited ..........6-39 GS1 DataBar Expanded..........6-40 Codablock A .............. 6-41 Codablock F .............. 6-42 PDF417 ..............6-43 MacroPDF417 ............6-44 MicroPDF417 ............6-44 GS1 Composite Codes ..........
  • Page 15 Chapter 8 - Utilities To Add a Test Code I.D. Prefix to All Symbologies..............8-1 Show Decoder Revision ..........8-1 Show Scan Driver Revision .........8-1 Show Software Revision..........8-1 Show Data Format............8-2 Test Menu..............8-2 EZConfig-Scanning Introduction........8-2 Installing EZConfig-Scanning from the Web ..8-3 Resetting the Factory Defaults ........8-4 Chapter 9 - Serial Programming Commands Conventions..............9-1...
  • Page 16 Replacing an Interface Cable ......11-2 Troubleshooting a Voyager 1400g Scanner....11-2 Chapter 12 - Customer Support Appendix A - Reference Charts Symbology Charts ............A-1 Linear Symbologies..........A-1 2D Symbologies ............ A-3 Postal Symbologies..........A-3 ASCII Conversion Chart (Code Page 1252) ....A-4 Lower ASCII Reference Table ........A-5 ISO 2022/ISO 646 Character Replacements ....A-10 Unicode Key Maps ............A-13...
  • Page 17 viii...

  • Page 18: Chapter 1 - Getting Started

    Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager™ 1400g area-imaging scanner. Product specifications, dimensions, warranty, and customer support information are also included. Note: The selections in this User’s Guide are dependent on the Voyager 1400g model you have purchased.

  • Page 19: Connecting With Keyboard Wedge

    The scanner beeps. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The unit defaults to a USB PC Keyboard. Refer to page 2-4 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Application Note,”...
  • Page 20 Turn the terminal/computer power back on. The scanner beeps. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. The unit defaults to an IBM PC AT and compatibles keyboard wedge inter- face with a USA keyboard.

  • Page 21: Connecting With Rs232 Serial Port

    Connecting with RS232 Serial Port Turn off power to the terminal/computer. Connect the appropriate interface cable to the scanner. Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.

  • Page 22: Connecting With Rs485

    Connecting with RS485 A scanner or cordless base can be connected for an IBM POS terminal interface. Connect the appropriate interface cable to the device, then to the com- puter. Turn the terminal/computer power back on. The scanner beeps. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.

  • Page 23: Reading Techniques

    Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corre- sponds to the scanner’s horizontal field of view. The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read.

  • Page 24: Setting Custom Defaults

    Setting Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before scan- nning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults.
  • Page 25 1 - 8...

  • Page 26: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.

  • Page 27: Rs232 Serial Port

    RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a car- riage return (CR) and a line feed (LF) suffix, baud rate, and data format as indi- cated below.

  • Page 28: Rs485 Packet Mode

    Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B UPC E Code 128 ** 00 18 0B...

  • Page 29: Usb Ibm Surepos

    USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register.

  • Page 30: Usb Hid

    USB HID Scan the following code to program the scanner for USB HID bar code scan- ners. USB HID Bar Code Scanner USB Serial Scan the following code to program the scanner to emulate a regular RS232- based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com).

  • Page 31: Verifone ® Ruby Terminal Default Settings

    ® Verifone Ruby Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data for- mat to 8 data bits, no parity bit, 1 stop bit. It also also adds a line feed (LF) suf- fix and programs the following prefixes for each symbology: Symbology Prefix...

  • Page 32: Honeywell Bioptic Aux Port Configuration

    Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Honeywell Bioptic Settings ©...

  • Page 33: Wincor Nixdorf Terminal Default Settings

    Wincor Nixdorf Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nix- dorf terminal. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Wincor Nixdorf Beetle™...

  • Page 34: Keyboard Country Layout

    Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are sup- ported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘...
  • Page 35 Keyboard Country (continued) Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) 2 - 10...
  • Page 36 Keyboard Country (continued) Estonia Faeroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) 2 - 11...
  • Page 37 Keyboard Country (continued) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia 2 - 12...
  • Page 38 Keyboard Country (continued) Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia 2 - 13...
  • Page 39 Keyboard Country (continued) Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) 2 - 14...

  • Page 40: Keyboard Style

    Keyboard Country (continued) Switzerland (German) Tatar Turkey F Turkey Q Ukrainian United Kingdom United Stated (Dvorak right) United States (Dvorak left) United States (Dvorak) United States (International) Uzbek (Cyrillic) Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Key-...
  • Page 41 Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S.

  • Page 42: Keyboard Conversion

    Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Conversion Alphabetic keyboard characters can be forced to be all upper case or all lower- case.

  • Page 43: Keyboard Modifiers

    Default = Off. Control Character Output On * Control Character Output Off Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is the preferred mode. All key- board country codes are supported.
  • Page 44 Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode. Default = Off Turbo Mode On * Turbo Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad.

  • Page 45: Rs232 Baud Rate

    RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 2400 4800 * 9600 19200 38400 57,600...

  • Page 46: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an applica- tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.

  • Page 47: Rs232 Receiver Time-Out

    RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time- out.

  • Page 48: Rs232 Timeout

    RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in millisec- onds) for a timeout by scanning the bar code below, then setting the time- out (from 1-5100 milliseconds) by scanning digits from the inside back cover, then scanning Save.

  • Page 49: Scanner To Bioptic Communication

    the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off. ACK/NAK On * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners.

  • Page 50: Scanner-Bioptic Ack/Nak Mode

    Scanner-Bioptic ACK/NAK Mode Bioptic ACK/Nak On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner- Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.
  • Page 51 2 - 26...

  • Page 52: Chapter 3 - Input/Output Settings

    Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off - Scanner * Power Up Beeper On - Scanner...

  • Page 53: Good Read And Error Indicators

    Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On.

  • Page 54: Beeper Pitch - Good Read

    Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scan- ner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2400 Hz) High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scan- ner emits when there is a bad read or error.

  • Page 55: Led - Good Read

    LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On. * LED - Good Read On LED - Good Read Off Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read.

  • Page 56: Good Read Delay

    Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = 0 ms (No Delay). * No Delay Short Delay (500 ms) Medium Delay (1,000 ms) Long Delay (1,500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.

  • Page 57: Led Illumination - Manual Trigger

    LED Illumination - Manual Trigger If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the scanner when the trig- ger is pressed. Default = High. Note: The LEDs are like a flash on a camera. The lower the ambient light in the room, the brighter the LEDs need to be so the scanner can “see”...

  • Page 58: Presentation Mode

    Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LED dims until a bar code is presented to the scanner, then the LED brightens to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly.

  • Page 59: Presentation Centering

    Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.

  • Page 60: Codegate

    Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right.

  • Page 61: Mobile Phone Read Mode

    Mobile Phone Read Mode When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. Hand Held Scanning - Mobile Phone Presentation Scanning -...

  • Page 62: User-Specified Reread Delay

    Use shorter delays in applications where repetitive bar code scanning is required. Reread Delay only works when in Presentation Mode (see page 3-7). Default = Medium. Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the...
  • Page 63 In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through the centering window, so it will not be read.

  • Page 64: No Read

    Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual.

  • Page 65: Video Reverse

    Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse Off bar code below is an example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes.

  • Page 66: Working Orientation

    Working Orientation Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright. Upright: Vertical, Top to Bottom: (Rotate CW 90°)
  • Page 67 3 - 16...

  • Page 68: Chapter 4 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 69: To Clear One Or All Prefixes Or Suffixes

    symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4.

  • Page 70: To Add A Carriage Return Suffix To All Symbologies

    Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix. Step 3.

  • Page 71: Suffix Selections

    Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page...

  • Page 72: Intercharacter Delay

    Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.

  • Page 73: Interfunction Delay

    Interfunction Delay An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the num- ber of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.

  • Page 74: Chapter 5 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For exam- ple, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
  • Page 75 you are programming. (See Primary/Alternate Data Formats on page 5-8 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 5-4) and locate the Terminal ID number for your PC. Scan three numeric bar codes on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits).

  • Page 76: Other Programming Selections

    Other Programming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing.

  • Page 77: Terminal Id Table

    Terminal ID Table Terminal Terminal Model(s) PC/AT and compatibles USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner RS232 True PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Serial Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character.

  • Page 78: Move Commands

    ASCII code, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-4 for decimal, hex and character codes. Send all but the last characters E9 Include in the output message all but the last “nn”...

  • Page 79: Miscellaneous Commands

    Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code.

  • Page 80: Data Formatter

    Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code.

  • Page 81: Primary/Alternate Data Formats

    Default = Data Formatter On, Not Required, Keep Prefix/Suffix. * Data Formatter On, Not Required, Keep Prefix/Suffix Data Format Required, Keep Prefix/Suffix Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3.
  • Page 82 Symbologies This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) • Matrix 2 of 5 •...

  • Page 83: All Symbologies

    All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.

  • Page 84: Codabar

    Codabar <Default All Codabar Settings> Codabar On/Off * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...

  • Page 85: Codabar Concatenation

    When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit...
  • Page 86 Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length 6 - 5...

  • Page 87: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit.
  • Page 88 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Charac- ter. * No Check Character Validate, but Don’t Transmit Validate and Transmit...

  • Page 89: Code 32 Pharmaceutical (Paraf)

    acter(s), it buffers Code 39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = Off. * Off Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Ital-...

  • Page 90: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.

  • Page 91: Interleaved 2 Of 5

    10), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly. Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Check Digit...
  • Page 92 When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...

  • Page 93: Nec 2 Of 5

    NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
  • Page 94 NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length 6 - 13...

  • Page 95: Code 93

    Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.

  • Page 96: Code 93 Code Page

    which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 93 bar code that starts with a character other than a space. Default = Off. * Off Code 93 Code Page Code pages define the mapping of character codes to characters.

  • Page 97: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information.

  • Page 98: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information.

  • Page 99: Matrix 2 Of 5

    Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-80.

  • Page 100: Code 11

    Code 11 <Default All Settings> Code 11 On/Off * Off Code 11 Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits 6 - 19...

  • Page 101: Code 128

    Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 <Default All Code 128 Settings>...
  • Page 102 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. * Off Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information.

  • Page 103: Code 128 Code Page

    Code 128 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.

  • Page 104: Gs1-128

    GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.

  • Page 105: Telepen

    Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pat- tern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).

  • Page 106: Upc-A

    Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC-A <Default All UPC-A Settings>...
  • Page 107 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it.

  • Page 108: Upc-A/Ean-13

    UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 6-26. Default = Not Required. Required * Not Required UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda.

  • Page 109: Coupon Gs1 Databar Output

    Default = Off. * Off Allow Concatenation Require Concatenation Coupon GS1 DataBar Output If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1 DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data.

  • Page 110: Upc-E0

    UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 6-32).
  • Page 111 UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda.
  • Page 112 UPC-E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data.

  • Page 113: Upc-E1

    UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 6-29). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. UPC-E1 On * UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings>...
  • Page 114 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.

  • Page 115: Isbn Translate

    EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 6-27).

  • Page 116: Ean/Jan-8

    EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On 6 - 35...
  • Page 117 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar...

  • Page 118: Msi

    <Default All MSI Settings> MSI On/Off * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check charac- ters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned...
  • Page 119 When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. * Validate Type 10, but Don’t Transmit Validate Type 10 and Transmit Validate 2 Type 10 Characters,...

  • Page 120: Gs1 Databar Omnidirectional

    GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On 6 - 39...

  • Page 121: Gs1 Databar Expanded

    GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 4-74.

  • Page 122: Codablock A

    Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.

  • Page 123: Codablock F

    Codablock F <Default All Codablock F Settings> Codablock F On/Off * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.

  • Page 124: Pdf417

    PDF417 < Default All PDF417 Settings > PDF417 On/Off * On PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.

  • Page 125: Macropdf417

    MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On. * On MicroPDF417 <...

  • Page 126: Gs1 Composite Codes

    MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a...

  • Page 127: Gs1 Emulation

    GS1 Composite Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435. Minimum Message Length Maximum Message Length GS1 Emulation...

  • Page 128: Tcif Linked Code 39 (Tlc39)

    Default = GS1 Emulation Off. GS1-128 Emulation GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component.

  • Page 129: Qr Code

    QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information.

  • Page 130: Qr Code Page

    information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = On. * On QR Code Page QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.

  • Page 131: Data Matrix

    Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.

  • Page 132: Data Matrix Code Page

    mined by information encoded in those bar codes. Once the proper num- ber of codes is reached, the data is output in the order specified in the bar codes. Default = On. * On Data Matrix Code Page Data Matrix Code pages define the mapping of character codes to charac- ters.

  • Page 133: Maxicode

    MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * Off MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.

  • Page 134: Aztec Code

    Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.

  • Page 135: Aztec Code Page

    ter(s), it buffers the number of Aztec bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = Off. * Off Aztec Code Page Aztec Code pages define the mapping of character codes to characters.

  • Page 136: Chinese Sensible (Han Xin) Code

    Chinese Sensible (Han Xin) Code < Default All Han Xin Settings > Han Xin Code On/Off * Off Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Mini- mum and Maximum lengths = 1-7833.
  • Page 137 China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi- mum Default = 80.

  • Page 138: Korea Post

    Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi- mum Default = 48.

  • Page 139: Postal Codes - 2D

    Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combina- tions that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is over- written.

  • Page 140: Combination 2D Postal Codes

    Planet Code On Also see Planet Code Check Digit, page 6-62. Postal-4i On Postnet On Also see Postnet Check Digit, page 6-62. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Bar Code and Postnet with B and B’...
  • Page 141 Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On Postal-4i and Intelligent Mail Bar Code On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and...
  • Page 142 Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Bar Code, and Postnet with B and B’...
  • Page 143 Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data.
  • Page 144 Australian Post Interpretation This option controls what interpretation is applied to customer fields in Aus- tralian 4-State symbols. Bar Output lists the bar patterns in “0123” format. Numeric N Table causes that field to be interpreted as numeric data using the N Table.
  • Page 145 6 - 64...

  • Page 146: Chapter 7 - Interface Keys

    Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-18 enable Control + ASCII mode. Function Code HEX/ASCII Value Full ASCII “CTRL”...
  • Page 147 The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States Belgium < Scandinavia <...

  • Page 148: Supported Interface Keys

    Supported Interface Keys IBM PC/AT and Compatibles, Apple Mac/iMac ASCII USB PC Supported Keys Keyboard Reserved Reserved Enter (KP) Enter/Numpad Enter Cap Lock CAPS ALT make ALT make ALT break ALT break CTRL make CNTRL make CTRL break CNTRL break CR/Enter RETURN Reserved...
  • Page 149 7 - 4...

  • Page 150: Chapter 8 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 151: Show Data Format

    Show Data Format Scan the bar code below to show current data format settings. DFMBK3?. Data Format Settings Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The pro- gramming function will still occur, but in addition, the content of that program- ming code is output to the terminal.

  • Page 152: Installing Ezconfig-Scanning From The Web

    Scan Data Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial commands to the scanner and receive scanner response that can be seen in the Scan Data win- dow.

  • Page 153: Resetting The Factory Defaults

    Resetting the Factory Defaults This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default set- tings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults.

  • Page 154: Chapter 9 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual.

  • Page 155: Query Commands

    Query Commands Several special characters can be used to query the device about its settings. What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a continuous range of values.
  • Page 156 NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters. When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.

  • Page 157: Resetting The Custom Defaults

    the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value. Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Acti- vate Custom Defaults bar code below.

  • Page 158: Menu Commands

    Menu Commands Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Product Default Settings Setting Custom Set Custom Defaults MNUCDP Defaults Save Custom MNUCDS Defaults Resetting the Activate Custom DEFALT Custom Defaults Defaults Programming the Interface Plug and Play Codes Keyboard Wedge: PAP_AT...
  • Page 159 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Plug and Play Codes: USB Keyboard (PC) PAP124 USB Keyboard PAP125 (Mac) USB Japanese TRMUSB134 Keyboard (PC) USB HID PAP131 USB Serial TRMUSB130 CTS/RTS Emulation USBCTS1 CTS/RTS Emulation USBCTS0 Off* ACK/NAK Mode On...
  • Page 160 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard *U.S.A. KBDCTY0 Country Albania KBDCTY35 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium KBDCTY1 Bosnia KBDCTY33 Brazil KBDCTY16 Brazil (MS) KBDCTY59 2-10 Bulgaria (Cyrillic) KBDCTY52 2-10 Bulgaria (Latin)
  • Page 161 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Czech KBDCTY40 2-10 Country (Programmers) Czech (QWERTY) KBDCTY39 2-10 Czech (QWERTZ) KBDCTY38 2-10 Denmark KBDCTY8 2-10 Dutch (Netherlands) KBDCTY11 2-10 Estonia KBDCTY41 2-11 Faeroese KBDCTY83 2-11 Finland KBDCTY2...
  • Page 162 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Latvia (QWERTY) KBDCTY43 2-13 Country Lithuania KBDCTY44 2-13 Lithuania (IBM) KBDCTY45 2-13 Macedonia KBDCTY34 2-13 Malta KBDCTY74 2-13 Mongolian (Cyrillic) KBDCTY86 2-13 Norway KBDCTY9 2-13 Poland KBDCTY20 2-13...
  • Page 163 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Ukrainian KBDCTY76 2-15 Country United Kingdom KBDCTY7 2-15 United Stated KBDCTY89 2-15 (Dvorak right) United States KBDCTY88 2-15 (Dvorak left) United States KBDCTY87 2-15 (Dvorak) United States KBDCTY30 2-15...
  • Page 164 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Keyboard Modifiers *Control + ASCII Off KBDCAS0 2-18 DOS Mode Control KBDCAS1 2-18 + ASCII Windows Mode KBDCAS2 2-18 Control + ASCII Windows Mode KBDCAS3 2-18 Prefix/Suffix Off *Turbo Mode Off KBDTMD0 2-19...
  • Page 165 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Word Length: Data 7 Data, 1 Stop, 2-21 232WRD3 Bits, Stop Bits, and Parity Even Parity 7 Data, 1 Stop, 232WRD0 2-21 Parity None 7 Data, 1 Stop, 232WRD6 2-21 Parity Odd...
  • Page 166 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Scanner-Bioptic *Bioptic ACK/NAK 232NAK0 2-25 ACK/NAK Mode Bioptic ACK/NAK 232NAK1 2-25 Scanner-Bioptic ACK/NAK Timeout 232DLK##### 2-25 ACK/NAK Timeout *5100 Input/Output Selections Power Up Beeper Power Up Beeper BEPPWR0 Off - Scanner *Power Up Beeper...
  • Page 167 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry LED - Good Read BEPLED0 BEPLED1 Number of Beeps - BEPERR3 Error Range 1 - 9 BEPERR# Number of Beeps - BEPRPT1 Good Read Range 1 - 9 BEPRPT# Good Read Delay *No Delay...
  • Page 168 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Presentation Presentation PDCWIN1 Centering Window Centering On *Presentation PDCWIN0 Centering Off Left of Presentation PDCLFT### Centering Window (*40%) Right of PDCRGT### Presentation Centering Window (*60%) Top of Presentation PDCTOP### Centering Window (*40%)
  • Page 169 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Centering Window Centering On DECWIN1 3-13 *Centering Off DECWIN0 3-13 Left of Centering DECLFT### 3-13 Window (*40%) Right of Centering DECRGT### 3-13 Window (*60%) Top of Centering DECTOP### 3-13 Window (*40%)
  • Page 170 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Function Code *Enable RMVFNC0 Transmit Disable RMVFNC1 Intercharacter Delay Range 0 - 1000 DLYCHR## (5ms increments) User Specified Delay Length DLYCRX## Intercharacter Delay 0 - 1000 (5ms increments) Character to Trigger DLY_XX##...
  • Page 171 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Symbologies All Symbologies All Symbologies Off ALLENA0 All Symbologies On ALLENA1 Codabar Default All Codabar CBRDFT Settings CBRENA0 CBRENA1 Codabar Start/Stop *Don’t Transmit CBRSSX0 Char. Transmit CBRSSX1 Codabar Check *No Check Char.
  • Page 172 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Code 39 Message Minimum (0 - 48) *0 C39MIN## Length Maximum (0 - 48) C39MAX## Code 39 Append *Off C39APP0 C39APP1 Code 32 *Off C39B320 Pharmaceutical C39B321 (PARAF) Code 39 Full ASCII *Off...
  • Page 173 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry NEC 2 of 5 Message Minimum (2 - 80) *4 N25MIN## 6-13 Length Maximum (2 - 80) N25MAX## 6-13 Code 93 Default All Code 93 C93DFT 6-14 Settings C93ENA0 6-14...
  • Page 174 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Matrix 2 of 5 Minimum (1 - 80) *4 X25MIN## 6-18 Message Length Maximum (1 - 80) X25MAX## 6-18 Code 11 Default All Code 11 C11DFT 6-19 Settings *Off C11ENA0...
  • Page 175 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Telepen Default All Telepen TELDFT 6-24 Settings *Off TELENA0 6-24 TELENA1 6-24 Telepen Output *AIM Telepen Output TELOLD0 6-24 Original Telepen TELOLD1 6-24 Output Telepen Message Minimum (1 - 60) *1 TELMIN## 6-25 Length...
  • Page 176 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry UPC-E0 Default All UPC-E UPEDFT 6-29 Settings UPEEN00 6-29 UPEEN01 6-29 UPC-E0 Expand *Off UPEEXP0 6-29 UPEEXP1 6-29 UPC-E0 Addenda Required UPEARQ1 6-30 Required *Not Required UPEARQ0 6-30 UPC-E0 Addenda UPEADS1...
  • Page 177 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry EAN/JAN-13 E13ADS0 6-34 Addenda E13ADS1 6-34 Separator ISBN Translate *Off E13ISB0 6-34 E13ISB1 6-34 EAN/JAN-8 Default All EAN/ EA8DFT 6-35 JAN 8 Settings EA8ENA0 6-35 EA8ENA1 6-35 EAN/JAN-8 Check EA8CKX0 6-35...
  • Page 178 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry MSI Check Character *Validate Type 10, MSICHK0 6-38 but Don’t Transmit Validate Type 10 and MSICHK1 6-38 Transmit Validate 2 Type 10 MSICHK2 6-38 Chars, but Don’t Transmit Validate 2 Type 10 MSICHK3...
  • Page 179 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry GS1 DataBar Default All GS1 RSEDFT 6-40 Expanded DataBar Expanded Settings RSEENA0 6-40 RSEENA1 6-40 GS1 DataBar Minimum (4 - 74) *4 RSEMIN## 6-40 Expanded Msg. Maximum (4 - 74) RSEMAX## 6-40 Length...
  • Page 180 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry MacroPDF417 PDFMAC1 6-44 PDFMAC0 6-44 MicroPDF417 Default All Micro MPDDFT 6-44 PDF417 Settings MPDENA1 6-44 *Off MPDENA0 6-44 MicroPDF417 Msg. Minimum (1-366) *1 MPDMIN### 6-45 Length Maximum (1-366) MPDMAX### 6-45 *366...
  • Page 181 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry QR Code Msg. Minimum (1-7089) QRCMIN#### 6-48 Length Maximum (1-7089) QRCMAX#### 6-48 *7089 QR Code Append QRCAPP1 6-49 QRCAPP0 6-49 QR Code Page QR Code Page (*3) QRCDCP## 6-49 Data Matrix...
  • Page 182 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Aztec Append AZTAPP1 6-54 *Off AZTAPP0 6-54 Aztec Code Page Aztec Code Page AZTDCP## 6-54 (*51) Chinese Sensible Default All Han Xin HX_DFT 6-55 (Han Xin) Code Code Settings HX_ENA1 6-55...
  • Page 183 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Single 2D Postal Australian Post On POSTAL1 6-58 Codes British Post On POSTAL7 6-58 Canadian Post On POSTAL30 6-58 Intelligent Mail Bar POSTAL10 6-58 Code On Japanese Post On POSTAL3 6-58 KIX Post On...
  • Page 184 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Combination 2D InfoMail and British POSTAL8 6-59 Postal Codes Post On Intelligent Mail Bar POSTAL20 6-59 Code and Postnet with B and B’ Fields Postnet and Postal- POSTAL14 6-59 4i On...
  • Page 185 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Combination 2D Postnet, Postal-4i, POSTAL24 6-61 Postal Codes and Intelligent Mail (continued) Bar Code On Planet, Postal-4i, POSTAL25 6-61 and Postnet with B and B’ Fields On Planet, Intelligent POSTAL26 6-61...
  • Page 186 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Show Decoder Revision REV_DR Show Scan Driver Revision REV_SD Show Software Revision REVINF Show Data Format DFMBK3? Resetting the Factory Remove Custom DEFOVR Defaults Defaults Activate Defaults DEFALT 9 - 33...
  • Page 187 9 - 34...

  • Page 188: Chapter 10 - Product Specifications

    Product Specifications Voyager 1400g Scanner Product Specifications Parameter Specification Mechanical Height 1.7 inches (43mm) Length 7.1 inches (180mm) Width 2.6 inches (66mm) Weight 4.2 ounces (119g) Electrical Input Voltage 4 to 5.5VDC Operating Power 2W; 400 mA (typical) @ 5VDC Standby Power .45W;...
  • Page 189 Parameter Specification 6.7 mil PDF417 25 - 90mm (0.99 - 3.54 in.) 10mil Data Matrix 25 - 95mm (0.99 - 3.74 in.) 20mil QR Code 15 - 195mm (0.59 - 7.67 in.) Guaranteed Performance 5 mil Code 39 50 - 84mm (1.97 - 3.3 in.) 13 mil UPC-A 34 - 200mm (1.34 - 7.87 in.) 10 - 2...

  • Page 190: Standard Cable Pinouts

    Standard Cable Pinouts Keyboard Wedge 10 - 3...

  • Page 191: Serial Output

    Standard Cable Pinouts Serial Output 10 - 4...

  • Page 192: Usb

    Standard Cable Pinouts 10 - 5...

  • Page 193: Rs485 Output

    Standard Cable Pinouts RS485 Output 10 - 6...

  • Page 194: Chapter 11 - Maintenance

    Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These ser- vices are to be performed only by an authorized service center (see Customer Support on page 12-1). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Device...

  • Page 195: Replacing An Interface Cable

    • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing an Interface Cable 1. Turn the power to the host system OFF. 2.
  • Page 196 • You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview beginning on page 4-1 for further information. Does the scanner read the bar code incorrectly? If the scanner reads a bar code, but the data is not displayed correctly on the host screen:...
  • Page 197 11 - 4...

  • Page 198: Chapter 12 - Customer Support

    Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below: Knowledge Base: www.hsmknowledgebase.com Our Knowledge Base provides thousands of immediate solutions. If the Knowl- edge Base cannot help, our Technical Support Portal (see below) provides an easy way to report your problem or ask your question.
  • Page 199 This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to HII factory or authorized service center for inspection. No product will be accepted by HII without a Return Materials Authorization, which may be obtained by contacting HII.

  • Page 200: Symbology Charts

    Reference Charts Symbology Charts Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID.
  • Page 201 Honeywell Possible Symbology modifiers GS1 DataBar GS1 DataBar Limited GS1 DataBar Expanded GS1-128 2 of 5 China Post (Hong Kong 2 of Interleaved 2 of 5 0, 1, 3 Matrix 2 of 5 NEC 2 of 5 Straight 2 of 5 IATA 0, 1, 3 Straight 2 of 5 Industrial 0, 1...

  • Page 202: 2D Symbologies

    2D Symbologies Honeywell Possible Symbology modifiers All Symbologies Aztec Code 0-9, A-C Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix GS1 Composite GS1 DataBar Omnidirectional...

  • Page 203: Ascii Conversion Chart (Code Page 1252

    Honeywell Possible Symbology modifiers China Post InfoMail Intelligent Mail Bar Code Japanese Post KIX (Netherlands) Post Korea Post Planet Code Postal-4i Postnet ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 dif- ferent ways, as shown below.

  • Page 204: Lower Ascii Reference Table

    Non-printable Keyboard Control + ASCII (CTRL+X) Mode ASCII control characters Windows Mode Control + X Mode On (KBDCAS2) Control + X Mode Off CTRL + X Char CTRL + X (KBDCAS0) function CTRL+ K hyperlink list, Delete CTRL+ L left align Enter / Ret CTRL+ M Insert...
  • Page 205 Printable Characters (Continued) DEC HEX Character DEC HEX Character DEC HEX Character & < > ⌂ Extended ASCII Characters PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code ↑ € Ç 0x48 up arrow ↓ ü 0x50 down arrow →...
  • Page 206 Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code † å Home 0x47 ‡ ç 0x4F ˆ ê Page Up 0x49 ‰ ë Page Down 0x51 Š è Right ALT 0x38 ‹ ï Right CTRL 0x1D Œ...
  • Page 207 Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code ¡ Control Break 0x9D ® « Alt Sequence with 1 Character 0x36 ¯ » Ctrl Sequence with 1 Character 0x1D ░ ° ▒ ± ▓ ² │...
  • Page 208 Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code ╘ Ô ╒ Õ ╓ Ö ╫ × ╪ Ø ┘ Ù ┌ Ú █ Û ▄ Ü ▌ Ý ▐ Þ ▀ ß α à á...

  • Page 209: Iso 2022/Iso 646 Character Replacements

    Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code √ û ⁿ ü ý ² ■ þ ÿ ISO 2022/ISO 646 Character Replacements Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
  • Page 210 Code Page Selection Standard Keyboard Honeywell Method/Country Country Code Page Option France ISO /IEC 646‐69 Germany ISO/IEC646‐21 Switzerland ISO /IEC 646‐CH Sweden / Finland  (extended Annex C) ISO/IEC 646‐11 Ireland ISO /IEC 646‐207 Danmark ISO/IEC 646‐08 Norway ISO/IEC 646‐60 Italy ISO/IEC 646‐15 Portugal ISO/IEC 646‐16 Spain ISO/IEC 646‐17 Spain ISO/IEC 646‐85 A - 11...
  • Page 211 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
  • Page 212 Unicode Key Maps 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 213 A - 14...
  • Page 214 Sample Symbols UPC-A Interleaved 2 of 5 0 123456 7890 Code 128 1234567890 EAN-13 Code 128 Code 39 9 780330 290951 Codabar BC321 Code 93 A13579B Straight 2 of 5 Industrial 123456-9$ 123456...
  • Page 215 Sample Symbols Matrix 2 of 5 GS1 DataBar 6543210 PDF417 (01)00123456789012 Car Registration Data Matrix QR Code Test Symbol Numbers 4-CB (4-State Customer Bar Code) 01,234,567094,987654321,01234567891 ID-tag (UPU 4-State) J18CUSA8E6N062315014880T...
  • Page 216 Sample Symbols Aztec Micro PDF417 Package Label MaxiCode Test Message Test Message Postnet Zip Code...
  • Page 217 Programming Chart...
  • Page 218 Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
  • Page 219 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1400-UG Rev B 3/14...

Table of Contents