Annovi Reverberi AR120LFP Instruction Manual

Annovi Reverberi AR120LFP Instruction Manual

Hide thumbs Also See for AR120LFP:

Advertisement

Quick Links

140° F - Max Water Temp
1 1/2" - Suction
1" - Outlet
AR120LFP / AR140LFP - 550
m
odeL
AR120LFP-C
AR120LFP-SP
AR120LFP-AP-SP/C
AR140LFP-C
AR140LFP-SP
AR140LFP-AP-SP/C
d
K
iAPHRAgm
iTS
m
d
odeL
eScRiPTion
AR43255
BlueFlex
AR43253
Desmopan
AR43252
NBR
AR43254
Viton
INSTRUCTION MANUAL
RPm
m
gPm
m
L/m
Ax
Ax
30.8
116.7
30.8
116.7
30.8
116.7
35.1
132.9
35.1
132.9
35.1
132.9
V
K
ALVe
iTS
m
d
odeL
eScRiPTion
AR43138
Valves
AR 120 LFP AR 140 LFP
- S
-H
emi
ydRAuLic
m
PSi
m
in
Ax
Ax
220
220
220
220
220
220
o-R
K
ing
iTS
m
d
odeL
eScRiPTion
AR43139
O-Rings
T
-d
HRee
iAPHRAgm
B
HP P
AR
oweR
15
4.5
15
4.5
15
4.5
15
5.2
15
5.2
15
5.2
o
iL
m
odeL
AR64532D
Oil
AR64532D-C Case (6)Oil
P
umP
w
eigHT
L
.
BS
34.4
34.4
34.4
34.4
34.4
34.4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AR120LFP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Annovi Reverberi AR120LFP

  • Page 1 AR 120 LFP AR 140 LFP 140° F - Max Water Temp 1 1/2” - Suction 1” - Outlet INSTRUCTION MANUAL AR120LFP / AR140LFP - 550 ydRAuLic HRee iAPHRAgm eigHT HP P odeL oweR AR120LFP-C 30.8 116.7 34.4 AR120LFP-SP 30.8 116.7...
  • Page 2 Application Kits Low Pressure AR31058 AR43329 Shaft Kit AR43392: 1 3/8” Male Spline Shaft Pulley Kit AR31058 Pulley 2A 11” Diameter 1" ³⁄₈ universal shaft For AR45, AR80 86,5 For Models: AR70, AR115 & AR135 Hydraulic Motor Flange Kit AR55371 AR55371 AR1514 $281.40...
  • Page 3: Important Safety Information

    IMPORTANT SAFETY INFORMATION Intended uses The pump is designed and constructed for incorporation in plants and machinery (spraying machines for the protective treatment of agricultural crops and garden plants). All other uses constitute misuse unless ap- proved by the manufacturer's technical service The pump must be used in a manner appropriate to its technical data (see “Technical Data”), and must not be modified or improperly used.
  • Page 4 Installation diagram (guideline) The following is a simplified illustration of the typical installation layout and is purely a guideline. Control Unit by-pass Tank Agitation Control Unit Intake filter Pump Delivery line filter...
  • Page 5: Installation Instructions

    INSTALLATION INSTRUCTIONS General guidelines on water supply connection To operate correctly, the diaphragm pump must draw in liquids from containers at atmospheric pressure. Do not supply the pump with pressurised liquids. For continuous duty, the pump should not draw in water by gravity from containers with liquid level at heights above 3 m.
  • Page 6 Safety recommendations for handling and lifting Before starting the operations, organise the intended working area so that the materials can be lifted and handled in safety. Unloading, loading, handling and lifting operations must be carried out by skilled, authorised, specifi­ cally trained staff.
  • Page 7: Installation

    Installation • The crankshaft may turn in either direction. • The water connection with the pump must be made using hoses of suitable diameter, in all case no less than that of the pump fittings, securing them to the fittings using good quality clamps. The intake hose must be coil-reinforced to prevent restrictions.
  • Page 8: Preliminary Checks

    Safety recommendations for use Before start-up, the operator must perform the necessary safety checks. In the event of leaks from the pressurized pipes, stop the pump at once and fix the leak. Do not operate the pump above the limits set by the manufacturer to increase its performance. Preliminary checks If the pump has a pressure accumulator, check its level of inflation, see "Checking the inflation pressure".
  • Page 9 Safety recommendations for maintenance Before doing any maintenance work, depressurise the water system and isolate the pump from all en- ergy sources. When the jobs are done, before restarting the pump, check that no tools, rags or other materials have been left close to moving parts or in hazardous zones.
  • Page 10 Table of lubricants The pump is delivered complete with high-performance 30 weight, non-detergent oil suitable for the intended ambient conditions (see "Environmental operating limits"). Inspecting the pump mounting Check that the pump's fixing screws have not become loose. If necessary, tighten them with the driving torque stated in the installation design. Inspecting the connections and pipes - Inspect the connections for leaks.
  • Page 11: Pump Storage

    Pump Storage It is important to comply with the recommendations for storage in the operator's manual of the machine into which the pump is incorporated. For the pump itself, at the end of pumping operations it is essential to flush out the pump by pumping clean water.
  • Page 12: Troubleshooting

    TROUBLESHOOTING The information provided is intended to provide guidance how to deal with malfunctions which may occur during use. Some of these procedures may be carried out by skilled staff, while others have to be performed at specialised service centres since they require the use of specific equipment as well as detailed knowledge of repair opera­ tions.
  • Page 13 TROUBLESHOOTING Remedy Problem Cause Oil seal on pump Replace the worn oil seal. shaft worn. Oil on pump body or base. Oil pressure inside pump too high. Restore correct oil level in tank. Pump using too much oil (oil flowing from delivery port) or oil Stop the pump at once.
  • Page 14 A.R. NORTH AMERICA A.R. NORTH AMERICA AR120LFP - AR 120 bp / AR140LFP - AR 140 bp 26 - 1 26 - 2 29 30 44 45 26 - 3 26 - 4 26 - 5 2021 AR North America...
  • Page 15 AP-SP/C 32019 33090 32021 AR120LFP 31710 31711 AR120bp AR120LFP - AR 120 bp / AR140LFP - AR 140 bp AR140LFP 32029 33091 32031 AR140bp 31712 31713 Code Description Code Description Note Note 3460010 Pump body 3460031 Manifold 3460100 Base Cataphoresis 1140450 O-ring Ø...

Table of Contents