Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Twin Eagles TEIM15-F
Summary of Contents for Twin Eagles TEIM15-F
- Page 1 Twin Eagles Outdoor Ice Maker Model: TEIM15-F 18909B 08/18...
-
Page 2: Table Of Contents
Leveling legs ..............4 Electrical Connection .............5 Installing the drain plumbing ..........5 Drain pump ................6 Connecting the water supply..........7 Dimensions for TEIM15-F............8 Recommended Rough in Opening Dimensions for TEIM15-F ...............8 Operation, Care, and Cleaning..........9 Operation (Turning on the ice machine)......9 The Ice Making Process ..........9 Ice Production ..............10... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Important Safety Instructions Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situa- If the ice machine was shipped or has been laying on its tions that may occur. Common sense, caution, and care back for any period of time allow the ice machine to sit must be exercised when installing, maintaining, or operat- upright for a period of at least 24 hours before plugging in. -
Page 4: Installing Your Ice Machine
(see “Electrical Connec- on the floor and level from side to side and front to back. tion” section). The overall height of your Twin Eagles ice machine may be adjusted from 33 ⁄ ” (85.7cm) with the leveling legs turned... -
Page 5: Electrical Connection
The ice machine must be installed to your local build- ing codes and ordinances. This drain pump is designed to be installed in Twin Eagles ice machines only. Failure to use an adequate drainage system, will result in surrounding water damage and/or poor ice production. -
Page 6: Drain Pump
OPTIONAL DRAIN PUMP The Twin Eagles Drain Pump is designed to remove drain water from ice machines installed in areas without direct drainage access. The sealed reservoir pump collects the melted ice water and pumps it to a maximum lift of eight (8) feet (2.44 meters) through... -
Page 7: Connecting The Water Supply
CONNECTING THE WATER SUPPLY Water Supply Observe and follow all local building codes when installing this appliance. This ice machine must be connected to a potable cold wa- ter supply line. delivering water pressure between a mini- mum of 20 psi and a maximum of 120 psi. ⁄... -
Page 8: Dimensions For Teim15-F
(7.6 to 8.8 cm) ⁄ ” (60 cm) ROUGH IN OPENING DIMENSIONS, FOR TEIM15-F Electrical Requirements: A grounded 115 volt, 15 amp dedicated circuit is required. A GFCI recep- tacle may be required for outdoor models. Power outlet can be located in the back wall behind the ice machine. -
Page 9: Operation, Care, And Cleaning
OPERATION, CARE, AND CLEANING OF YOUR ICE MACHINE Operation (Turning on the ice machine) Once the drain and water supply are connected, and the ice machine is in place and leveled, plug in the service cord. Place the switch to the “ON” position to turn on the ice machine. -
Page 10: Ice Production
OPERATION, CARE, AND CLEANING OF YOUR ICE MACHINE Care of the Ice Machine The bin level sensor is located in the ice bin, it senses when the ice supply is low or full and starts or stops the ice 1. Avoid leaning on the cabinet door. You may bend the making process accordingly. -
Page 11: Cleaning The Ice Machine
OPERATION, CARE, AND CLEANING OF YOUR ICE MACHINE Cleaning the Ice Machine Remove the drain plug at the bottom of the reservoir to Some impurities will remain and build up in the ice machine drain any remaining water and then reinstall. and stick to the ice machine’s parts over time. - Page 12 OPERATION, CARE, AND CLEANING OF YOUR ICE MACHINE 6. Determine the proper amount of cleaner from the ice Splash shield brackets machine cleaner manufacturer’s mixture ratio based on ⁄ gallon (2.81 liters) of water (refer to the manufac- turer’s mix ratio directions). Check to be sure the reser- voir drain plug is installed that was removed in step 4.
-
Page 13: Stainless Steel Maintenance
STAINLESS STEEL MAINTENANCE Background NOTE Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stain- Stainless steel products should never be installed, or stored less steels can discolor or corrode if not maintained prop- in close proximity to chlorine chemicals. -
Page 14: Troubleshooting Guide
TROUBLESHOOTING GUIDE Before calling a service provider try the trouble shooting production cycle can take up to 1 ⁄ hours. Initial start up suggestions below. cycles can take longer. Check the ice machine after 24 hours for ice accumulation in the bin. Is the reservoir drain plug in place? Check that the Ice Machine Operation reservoir drain plug is properly seated. -
Page 15: Energy Saving Tips
Check the drain pump reservoir may not have filled properly or the drain is discharge and vent line or any restrictions or kinks. Check leaking. Call Twin eagles customer service at that the drain pump is level. 562-802-3488. -
Page 16: Preparing The Ice Machine For Storage
PREPARING THE ICE MACHINE FOR STORAGE If the ice machine is moved, not used for an extended pe- 8. Reconnect the water valve outlet water line.(See Figure riod of time, or will be in an area that may experience freez- 23a). - Page 17 PREPARING THE ICE MACHINE FOR STORAGE Figure 21 Back view of Water ice machine supply line Figure 23 Water supply fitting To disconnect the water outlet Water valve line: Push up on the white collar inlet and pull the plastic water line from the bottom of the water Figure 21a valve.
-
Page 18: Drain Pump Removal Instructions
DRAIN PUMP REMOVAL INSTRUCTIONS 14. Remove the top clamp from the vent tube, for easier To Restart the Ice Machine access for the air hose. 1. With the rocker switch in the OFF position, plug the ice 15. Apply air pressure (approximately 10 psi) to the end of machine into an electrical outlet. - Page 19 DRAIN PUMP REMOVAL INSTRUCTIONS Remove these 4 hose clamps, then remove It may be necessary to disconnect the 3 tubes from the this electrical connection on factory drain pump installed drain pumps Unscrew the leveling leg so Figure 25 Drain pump the end of the threads is flush ground wire with the top of the nut insert.
-
Page 20: Obtaining Service
If You Do Need Service 9) Checked for water leaks after installation of the drain If you do need service, contact your dealer or Twin Eagles. pump. In any correspondence, refer to the service number and 10) Check for vibrations caused by improper installation. -
Page 21: Warranty
Limited One Year Parts and Labor Warranty Not Supplied or Designated by Twin Eagles Twin Eagles warrants that it will supply all necessary parts The above warranties also do not apply if: and labor to repair or replace in the end user’s home or office, any component which proves to be defective in ma- •... - Page 23 13259 http://www.twineaglesgrills.com/contactus.shtml...
- Page 24 41014792 rev B 7/26/18 13259...
Need help?
Do you have a question about the TEIM15-F and is the answer not in the manual?
Questions and answers