Magnadyne Silencer SL-3 Operation Manual

QUICK START INSTALLATION GUIDE
If you are not proficient in the installation of this product or would
like a full version of the installation manual, Please visit our web
site @ www.silencer.com
FOR PROFESSIONAL INSTALLATION ONLY!
ALARM FEATURE "A" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
rd
2. Push the Valet switch 3 times and hold in on the 3
release the valet switch. You are now in the Alarm feature A programming mode.
3. Press the transmitter button corresponding to the feature you want to program.
4. Press the transmitter button again to change the feature. Simply keep pressing the
transmitter button again until the module advances to your desired setting.
One Chirp /
Press
LED one pulse Two Chirps /LED
Transmitter
Factory Default two pulses
Button
Setting
1
Passive arming
Active arming
without passive
door locking
Automatic Automatic Rearm
2
Rearm off on
45 seconds
3
Instant Door Ajar
delay Door Ajar
error chirp
error chirp.
4
Siren
All Confirmation
Confirmation
chirps On
chirp on only
5 +
White wire=
White wire= 4th
Dome Light
Channel pulsed
Output
Lock/Arm &
6 +
Lock/Arm
Unlock/Disarm
Confirmation Chirp
Confirmation
Only
Chirps
ALARM with Keyless Entry
7. +
Keyless Entry ONLY
Car Jacking Car Jacking
8. +
feature Off feature On
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm
exit.
ALARM FEATURE "B" PROGRAMMING:
1 Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2 Push the Valet switch 4 times and hold in on the 4
heard, release the valet switch. You are now in the Alarm feature 'B' programming
mode.
3 Press the transmitter button corresponding to the feature you want to program.
One Chirp / LED
Press
one pulse Two Chirps / LED
Transmitter
Factory Default two pulses
Button
Setting
Pathway Parking light turns
1
illumination "on" for 30-
feature "off" second upon an
unlock signal
2
controlled door
push. When a long chirp is heard,
3
3rd Channel
4
Trunk Pulsed,
Four
Three Chirps
Chirps
5 +
/LED three
/LED four
Silent
pulses
pulses Arm/Disarm
Gray Wire =
Passive arming
6 +
Trunk (Channel
with passive
3) Output
door locking.
Horn chirp 20
7. +
mS
ALARM FEATURE "C" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
All
2. Push the Valet switch 5 times and hold on the 5
Horn
Confirmat
release the valet switch. You are now in the Alarm feature 'C' programming mode.
Confirmation
ion chirps
3. Press and hold the transmitter
chirp on only
off
mode.
White
Press
White =4th
=4th
Transmitter
channel
channel
Button
Momentary
Latched
1
2.
3 +
ADJUST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
Turn the Ignition switch 'ON/OFF' 3 TIMES and stay in OFF position.
Push the Valet switch 6 times holding in on the 6th push. until a long chirp will be
heard. Release the valet switch. You are now in the feature 'Shock Sensor' programming
mode.
Press and hold
accept adjustments of the shock sensor. Press
th
push. When a long chirp is
decrease sensitivity level by one. Each time the button is pushed and a decrease is made
the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity.
Warn away & full trigger will be deleted when minimum sensitivity is selected. Shock
sensor OFF. Press
Four
one. Each time an increase is made the siren/horn chirp will respond with [1] chirp. Two
Three Chirps / Chirps /
chirps indicate the maximum sensitivity. Hit the bumper or strong metal part of the vehicle to
LED three pulses LED four
test the threshold level of the sensor.
pulses
a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp.
Parking light turns
b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp.
"on" for 30-
When you are satisfied with the setting, press the
second unlock
long siren chirp will indicate the unit has locked in the adjustment.
signal & 10- lock
Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps,
the unit will exit the program mode. Three long chirps will confirm exit.
SL-3
Ignition
Ignition controlled Ignition controlled
locks & door locks only door unlocks only
unlocks
0.8-second
3.5-second Door Double pulse
Door lock
lock pulse. unlock
pulses.
3rd Channel
Trunk Momentary
Button = Button =
channel 4 AUX 1
Gray Wire = Two
Step Door Unlock
Output
Horn chirp 50 mS Horn chirp 30 mS
th
push until a long chirp is heard then
button for two seconds to enter shock sensor program
One Chirp / Two Chirps /
LED one pulse Factory Default LED two pulse
Setting
Shock Sensor Program Mode
ADS DBI protocol Fortin DBI Protocol
No Function
DBI start output on channel 4
button for 2 seconds. One long siren chirp will indicate the unit is ready to
button on the transmitter once. This will
button on the transmitter once. This will increase sensitivity level by
button to lock in the adjustment. One
Without ignition
controlled door
locks & unlocks
Comfort
feature
Horn chirp 10
mS